|Dec 15, 2007, 07:33 PM|
Ok, I found where to vote.
I voted for a plane that I don't have built yet, but I can see by the plans that it will be an awesome little Jet. I have a couple of similar planes, but none with a sweeping wing.
|Dec 15, 2007, 09:47 PM|
Just use regular APC props, and put the on the motor with the markings toward the motor. Motor should spin clockwise looking at the shaft. Opposite direction of a front mounted motor. To reverse the direction of a brushless motor, just switch any two leads.
|Dec 15, 2007, 10:30 PM|
Geeez this bird is getting Raves in the Voting !
I'm may have to order a few more BOXes of foam from RCFoam
and entertain another run after the new year.
|Dec 16, 2007, 09:44 AM|
I'm in the middle of the build, just waiting for my order from UH to come in. I could make do with what I've got on hand, except for the wing servo....
|Dec 16, 2007, 11:18 AM|
Rmg: I'll letcha know after the New Year.
Right now I'm kinda tired of doing "part sets"
I dont DO full KITS !
I'm not a business - just a retired guy with a cnc.
Plus Mike has run me out of foam.
I've made about 28 sets of parts so far.
At 3 sheets of depron per set, you'd be out of foam too :-)
|Dec 16, 2007, 03:43 PM|
Hey I was stationed in Warner Robins from 70 - 72 ! PEMEL
We used to fly south of town down towards Bonaire !
Base property but Off Base !
There is one pic here http://www.balsabuddies.com/cutouts/bot.jpg
I had just finished cutting some giant ribs for a Horton III
That is an 4' x 8' steel table !
Then a coupla more at the bottom !
It's NOT serious CNC as it's only Stepper motor driven not Servo motors.
But It cuts what I want when I want and as many times as I want.
I use a 1/8" bit in a router to cut foam - Cant afford a Laser
Still I bet this isnt very impressive, eh ? :-)
Just an Old Laptop PC serial linked to a control box and a huge linear
powersupply for powering the 4 ea. steppers.
I made the GEARDOWN mechanisms myself.
Sorry, no antibacklash gears.
Two steppers on the X axis,
One stepper on each of the Y & X axis.
6" C channel Steel rails and legs on the table with 4"x4"x/1/4" angle
and 2"x2"x1/4" angle cross pieces.
Reasonably sturdy but not perfect.
Over the years I've cut thousands of 1/4" Balsa parts
for a NON MODELING type of business.
BalsaUSA knows me well.
|Dec 16, 2007, 04:15 PM|
I was PEMEL on my way OUT of the service !
Did F-105 weapons control. Then came to WR
and got to repair SightHeads for them and 111's too.
U2 - that sound like it could have been Kewel !
Preditor, even more kewel !
2nd kid was born at HOUSEton cty offbase.
Ah the good ol days ! ( well after 30+ yrs they were )
|Dec 16, 2007, 06:01 PM|
Amazingly enough, my order from UH arrived today. I don't think I've ever received anything on a Sunday. I must have inadvertently ugraded the shipping or something.
So now I've got my wing servo mounted and I'm almost ready to seal up th bottom, just need to pick up some longer wires from the ESC to the battery. I guess it's off to Radio Shack tommorow.....
Does anyone know what guage wire I should buy to extend the ESC?
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Update for F-14 EDF plan buyers.||bipeflyer||Electric Ducted Fan Jet Talk||6||Feb 11, 2005 01:10 AM|
|F-14 Scale EDF Whos kit is it ???||F900||Electric Ducted Fan Jet Talk||6||Dec 07, 2001 08:26 AM|
|F-14 Tomcat EDF,pictures and questions||bipeflyer||Electric Ducted Fan Jet Talk||13||Jul 14, 2001 06:10 PM|
|Great Plane F-14 and Learjet conversions||sbarrow||Sport Planes||1||Jun 24, 2001 08:00 PM|
|f-14 center of gravity verus center of lift||tony houk||Power Systems||5||May 14, 2001 01:48 PM|