HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Sep 18, 2007, 09:23 AM
ProBro # 501
Boss248's Avatar
Austin Tx
Joined Jul 2005
1,861 Posts
Discussion
I am looking for a JR 9303 guru

I am totally confused...I have a Gold berg bipe thst I am finally finishing. My problem is I am running 2 servos one for each but Can't get my tx to gang them together and still have trim on 1 elevator. Is the any one out there that can help. I am not a newbie just a dummy..

Boss
Boss248 is offline Find More Posts by Boss248
Reply With Quote
Sign up now
to remove ads between posts
Old Sep 18, 2007, 10:01 AM
In NY's beautifull hills
staggerwing's Avatar
Binghamton Broome Cty, New York, United States
Joined Jun 2004
1,126 Posts
Boss,
You're in the wrong forum---this is giant scale elec planes
staggerwing is offline Find More Posts by staggerwing
Reply With Quote
Old Sep 18, 2007, 10:44 AM
ProBro # 501
Boss248's Avatar
Austin Tx
Joined Jul 2005
1,861 Posts
Quote:
Originally Posted by staggerwing
Boss,
You're in the wrong forum---this is giant scale elec planes
I thought someone might have run into this problem..what forum should I be in..>>>

Boss
Boss248 is offline Find More Posts by Boss248
Reply With Quote
Old Sep 18, 2007, 11:09 AM
RC Maniac
spyderron's Avatar
Astoria, OR
Joined Dec 2005
37 Posts
This should get you going in the right direction.
http://www.rcuniverse.com/forum/m_57...tm.htm#5754053

If not, go to the JR site and look through the different setups they have. They explain it well. Personally, I have a matchbox on my 50cc so I don't have to adjust the rt and lt elevator endpoints manually.

Ron
spyderron is offline Find More Posts by spyderron
Reply With Quote
Old Sep 19, 2007, 08:11 AM
Jim H
Memphis
Joined Dec 2004
509 Posts
Go into 'DEVIC SEL' set AUX2 to INH
Then go to 'WING TYPE' set ELEV mate to AUX2.
Plug the right elevator servo into elev and the left elevator servo into aux2
Use servo rev as required.


Jim
Fool is online now Find More Posts by Fool
Reply With Quote
Old Sep 19, 2007, 11:59 AM
ProBro # 501
Boss248's Avatar
Austin Tx
Joined Jul 2005
1,861 Posts
Quote:
Originally Posted by Fool
Go into 'DEVIC SEL' set AUX2 to INH
Then go to 'WING TYPE' set ELEV mate to AUX2.
Plug the right elevator servo into elev and the left elevator servo into aux2
Use servo rev as required.


Jim
Thanks Jim..that did the trick..I bet I wasted 3hr. on this damned JR 9303..it;s might be futaba..who knows for sure..it might be 2.4 for all of us..

Happy Boss..I thought I was going to have to use one of the servo reverser which I have had bad reports on them.so I am delighted to say the least.
Boss248 is offline Find More Posts by Boss248
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Looking For Jr Micro Reciever-jr610m SKYWARN Aircraft - Electric - Airplanes (FS/W) 3 Jan 04, 2003 05:08 PM
Cool I am looking for a RTF or ARTF that is under $200 Wingo1121 Aircraft - Fuel - Airplanes (FS/W) 12 Oct 24, 2002 11:10 PM
I am looking for a jet rcman Electric Ducted Fan Jet Talk 1 Sep 06, 2002 10:52 AM
Looking for a JR fm receiver, at least 4 channel deadcell Aircraft - Electric - Airplanes (FS/W) 2 Oct 11, 2001 06:32 PM