|Oct 23, 2006, 08:08 PM|
NIP Himodel/Emax Professional Series 30 amp Brushless ESC 2-4S fully programmable
I have a new shipment of brushless 30 amp ESCs in. They are unlabeled HiModel/Emax Professional Series ESC, and have many programming features not found in many ESC and the good news is that it does not require a programming card. They are a very nice ESC for the price. I have tested this ESC and the throttle response is very good and so far is working well with all outrunners and inrunners I have tested.
Current rating: 30amp continuous (40A burst)
Weight: 25 grams
BEC: 2 amps (5volts), 4 micro servos on 3 cell lipo, and 3 micro servos on 4 cell lipo
Battery: 2-4 cell lipo, 5-12 cell NiMh/NiCd
Auto Lipo cell detection
Maximum RPM: 210,000 rpm 2poles, 70,000 rpm (6 poles), and 35,000 rpm (12 poles)
Programmable Features: (all can be programmed with the throttle stick):
Brake: on or off
Battery Type: Lipo or NiMh/NiCd
Cutoff type: throttle down or hard cut off
Lipo cutoff voltage: 2.5, 2.75, or 3.0 volts per cell
Startup mode, normal, soft, super soft
Timing: Low, Medium, High
Governor model: on or off
All programming can be done through the transmitter. Unlike other budget ESC which need a Jeti card to get these advanced programming features. All features can be programmed via the throttle stick (except the arming song, see below). A lighted LED programming card is also available to program on the field to allow quick setting changes. The programming card does have one added feature and that is you have 16 songs in which to choose to from for your arming sound if you so wish.
They also have a nice feature to autocalibrate the throttle stick. Move the throttle to full up, then plug in the battery and wait for two beeps, then move the throttle stick down. Wait for the ESC to arm. You now have FULL throttle range where full up is 100% throttle. I have verified all programming features through the throttle stick. I also measured the LVC value, with a 3 cell lipo and 3.0 volts per cell setting, the ESC cut out at 9.01 volts. Programming is very easy to do, and only takes a few minutes to go through all the menus.
Every ESC now comes with a 3 pairs of 3.5mm bullet connectors and 6 pieces of heat shrink tubing.
Price is $30 each plus $2 flat shipping for any quantity.(These sell for $45 plus shipping on the Himodel website plus you have to wait for overseas shipping!). The optional programming cards are $8 each (I have only a few in stock) Paypal preferred.
My paypal is firstname.lastname@example.org
Please include your RCGroups name so I can leave you feedback.
Last edited by The Don; Oct 27, 2006 at 09:33 PM.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Sold||NIP Great Planes Silver Series 12 amp brushless ESC||Vintauri||Aircraft - Electric - Power Systems (FS/W)||2||Mar 02, 2007 09:51 AM|
|Sold||NIP Himodel/Emax Professional Series 30 amp Brushless ESC 2-4S fully programmable||The Don||Aircraft - Electric - Power Systems (FS/W)||4||Nov 21, 2006 11:43 AM|
|Sold||NIP Himodel/Emax 18 amp brushless ESC 2-4S lipo fully programmable||The Don||Aircraft - Electric - Power Systems (FS/W)||4||Nov 20, 2006 09:30 PM|
|Sold||NIP Himodel/Emax 25 amp brushless ESC 2-4S lipo fully programmable||The Don||Aircraft - Electric - Power Systems (FS/W)||8||Nov 13, 2006 06:37 PM|
|Sold||NIP Himodel/Emax 18 amp brushless ESC 2-4S lipo fully programmable||The Don||Aircraft - Electric - Power Systems (FS/W)||12||Nov 07, 2006 09:20 PM|