HobbyKing.com New Products Flash Sale
 
Thread Tools
Old Jul 06, 2006, 12:11 PM
Prepair Ltd
Guest
n/a Posts
Colchester 4-jaw Chuck wanted V/Urgently

Vince up the road has just popped in, he needs a Colchester fitting 4-Jaw chuck
to fit a Colchester Bantam lathe, and needs it here for tomorrow sometime.

7"-8" diameter or thereabouts, whatever is available, fitting is Colchester
3-prong type.

I'm going to Burton on Trent in the morning, so will be travelling past John S's
place, or what is available?

Peter
--
Peter A Forbes
Prepair Ltd, Luton, UK
prepair@easynet.co.uk
http://www.prepair.co.uk
Old Jul 06, 2006, 12:11 PM
Wayne Weedon
Guest
n/a Posts
Re: Colchester 4-jaw Chuck wanted V/Urgently

Prepair Ltd wrote:
> Vince up the road has just popped in, he needs a Colchester fitting 4-Jaw chuck
> to fit a Colchester Bantam lathe, and needs it here for tomorrow sometime.
>
> 7"-8" diameter or thereabouts, whatever is available, fitting is Colchester
> 3-prong type.


Sounds like you mean a D1-3 camlock.. He could of just ordered one
from J&L if he wanted one to keep, and the cost was not out of the question.

The chipmaster uses the same fitting...
Old Jul 06, 2006, 02:11 PM
John Stevenson
Guest
n/a Posts
Re: Colchester 4-jaw Chuck wanted V/Urgently

On Thu, 06 Jul 2006 17:26:14 +0100, Prepair Ltd
<prepair@easynet.co.uk> wrote:

>Vince up the road has just popped in, he needs a Colchester fitting 4-Jaw chuck
>to fit a Colchester Bantam lathe, and needs it here for tomorrow sometime.
>
>7"-8" diameter or thereabouts, whatever is available, fitting is Colchester
>3-prong type.
>
>I'm going to Burton on Trent in the morning, so will be travelling past John S's
>place, or what is available?
>
>Peter


Got a chuck but no spare backplate.
--
Regards,

John Stevenson
Nottingham, England.

Visit the new Model Engineering adverts page at:-
http://www.homeworkshop.org.uk/
Old Jul 06, 2006, 04:11 PM
Tim Leech
Guest
n/a Posts
Re: Colchester 4-jaw Chuck wanted V/Urgently

On Thu, 06 Jul 2006 18:40:38 GMT, John Stevenson
<john@stevenson-engineers.co.uk> wrote:

>On Thu, 06 Jul 2006 17:26:14 +0100, Prepair Ltd
><prepair@easynet.co.uk> wrote:
>
>>Vince up the road has just popped in, he needs a Colchester fitting 4-Jaw chuck
>>to fit a Colchester Bantam lathe, and needs it here for tomorrow sometime.
>>
>>7"-8" diameter or thereabouts, whatever is available, fitting is Colchester
>>3-prong type.
>>
>>I'm going to Burton on Trent in the morning, so will be travelling past John S's
>>place, or what is available?
>>
>>Peter

>
>Got a chuck but no spare backplate.


Too late for tomorrow, but I do have a spare D1-3 4-jaw. Only
available if you collect this ****** Ward lathe, though <G>

Tim

Dutton Dry-Dock
Traditional & Modern canal craft repairs
Vintage diesel engine service
Old Jul 06, 2006, 04:11 PM
Peter A Forbes
Guest
n/a Posts
Re: Re: Colchester 4-jaw Chuck wanted V/Urgently

On Thu, 06 Jul 2006 20:10:39 +0100, Tim Leech <duttondock@onetel.no.spam.com>
wrote:

>Too late for tomorrow, but I do have a spare D1-3 4-jaw. Only
>available if you collect this ****** Ward lathe, though <G>
>
>Tim


If only you knew..... :-))

I'll be in touch re the collection, the trailer is hors de combat due to
something unforeseen (don't ask!)

What size is the chuck?

Peter
--
Peter & Rita Forbes
Email: diesel@easynet.co.uk
Web: http://www.oldengine.org/members/diesel
 


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
480 brushed 7.4 or 11.1 V Steve Guinn Power Systems 11 Aug 25, 2004 10:36 PM
UltraFlyer - 4.5' chuck glider to E-Power ??? Alan W Foamies (Kits) 10 Nov 19, 2001 08:09 PM