Originally Posted by klique

Or randy at dynamoelectrics.com has them,give him a call i dont think they are on his site yet but he has them.
Ck

I've got 2 of 'em... one had white wires and one has black wires. I haven't tested with either yet (maybe this weekend?), but as I recall one was an earlier rev and the other a later revision. I'll report a side by side....

Chuck (in Aaaala Baaama)

I would go with Randy at

http://dynamoelectrics.com/

Or

http://www.warbirds-rc.com/

These guys are great Good price and in my case unbelivable service after the sale..


Both Vendors are top notch Same as CK.

Chuckand ,,,,, Looking good so far... I love my TL 50!!! now I just need to get busy on my Demon....

Originally Posted by TaSaJaRa

Chuckand ,,,,, Looking good so far... I love my TL 50!!! now I just need to get busy on my Demon....

Thanks! If all goes well, it'll look a LOT better by Monday! I'll report progress then.....

Chuck (in Aaaala Baaama)

Just wondering is the CC60 overkill for a motor that can only draw 22amps max? ( i.e. The HET 4wind mentioned earlier, in chuckands initial 50" TL component selection) Hmmm?

Happy FAST Flying!!!

Talon we pull 40 amps all day long through these motors their ratings are verry consevative.
Chucks setup pulls 42 amps at 24.5 k rpm on the het 4 wind.
ck

Originally Posted by Talon713

Just wondering is the CC60 overkill for a motor that can only draw 22amps max? ( i.e. The HET 4wind mentioned earlier, in chuckands initial 50" TL component selection) Hmmm?

Happy FAST Flying!!!

ck,

That sounds more like it. I was looking at the specs on the Warbirds R-C site. With those numbers the performance would be pretty lethargic, and the motors would probably last forever. But if your pulling that kind of amps, it must rock!!
BONUS...and the price is right... I may have to try one!

Talon

Talon ,bang for the buck you cant beat them I have a few and have used'm for a while.
I havnt even killed one yet,LoL
They work great in a few differant aplications of 3 s 4 s 6 s ,All depending on your needs.
ck

ck-
Sounds good, Thanks, I'll definately get one and put it thru it's paces. I've had great luck with Megas. They're hard to beat, but a little spendy. BTW- Is Warbirds the place to get them?

Talon

FyI Het's are megas.Shhh dont tell anyone.
Ck

Originally Posted by Talon713

ck-
Sounds good, Thanks, I'll definately get one and put it thru it's paces. I've had great luck with Megas. They're hard to beat, but a little spendy. BTW- Is Warbirds the place to get them?

Talon

Will do , I've bought from Randy before he's a great guy, I'll go Dynamo!

Later-

Talon

Yo talon randy is my Bro call him a slacker , dirtbag when you talk to him.
Randy is a pretty alrite dude.
Ck.

Originally Posted by Talon713

Will do , I've bought from Randy before he's a great guy, I'll go Dynamo!

Later-

Talon

Ha!Ha! sure will-

Thanks for the heads-up!

Talon

So... as promised, here are some pics following the weekend fray.

No great magic here, but I spent about 2 hours over the weekend getting the 50" TL glassed. Had to fit the motor/electronics late last night for grins and spin it up.

I used 6" wide 'glass, as that was all that was available locally. Chris uses 4" in the video, and it may be a little easier to handle, but the 6" worked great for me. Plenty of time to get it applied before the 3M 90 cranked. 6" width made VERY short work of it as well. I am very pleased with the appearance, the rigidity, and the straightness! I left the wing weighted in the (shimmed) beds for both sides and it is flat as a board! Feels like one too....

Ready for covering.... and flight very soon! I'll pick up covering the next night or two and should have it covered by the weekend. Batts may not be in for the weekend maiden though... Fingers crossed...

Oh... right... FYI, the prop is on backwards in the pics too.... Spun it up. No wind. Flipped the prop, mucho wind.

Chuck (in Aaaala Baaama)

Dude, your prop is on backwards.