HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Apr 15, 2007, 08:06 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Carlos, Charlie, the pilot is really psyqued this time around. My wife also told me today the project is not leaving the work table until it's finished...isn't that wonderful!!...

Today I finished the outer wing panel to center section wing joint reinforcement on the top wing (the lower wing was done already)...

I also finished the final glueing of the two forward cabane struts...

I'm now cutting plywood gussets that will reinforce the fuselage truss where it comes together near the cabane struts mounting areaand also at the bottom where the lower wing will bolt to the fuselage...

Carlos, I know you'll like this...the whole tail group is ready for covering!!!...I will do this as I work on other areas of the plane since this will serve as extra inspiration to finish...

As far as photos....I'll post every other day, so as not to slow down the momentum...

More to come!!!...

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Sign up now
to remove ads between posts
Old Apr 15, 2007, 08:32 PM
Account closed
Joined Oct 2002
35,016 Posts
Super news!

Gerry,

Just great news about the model will not leave the area until it's complete! Just super news and very nice of your wife!

Yes, keep it going and sooner than you know it, you will be out-fitting her with that PJS brushless outrunner that Henry sold you!!!

Super!
guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Sep 20, 2007, 02:22 PM
Account closed
Joined Oct 2002
35,016 Posts
bump....

guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Oct 28, 2007, 11:03 AM
Account closed
Joined Oct 2002
35,016 Posts
I trust this project is back on track.....RIGHT
guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Nov 11, 2007, 10:40 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Today I built the landing gear frame. This landing gear will have some shock absorbing. Notice on the second photo the wire clip that will allow looping a small rubber band between the upper and the lower struts.

Tomorrow I'll start on the landing gear fairings that will cover the frame.

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Old Nov 12, 2007, 08:31 AM
Registered User
Big_Bird's Avatar
Arlington Texas
Joined Oct 2005
164 Posts
Gerry, that is looking great.

Ken
Big_Bird is offline Find More Posts by Big_Bird
Reply With Quote
Old Nov 12, 2007, 05:15 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Ok. Yesterday I finished the wire skeleton or frame for the landing gear.

Today, I built the ribs around this frame to give it the airfoil shape.

The full size Jungmeister uses oleo struts for shock absorption upon landing.

The oleo struts are covered by a ribbed airfoil to improve its aerodinamic characteristics.

Attached is a reference photo of a Jungmeister in flight. Notice how much the gear struts extend when in the air.

The second and third photos show the framing process on the model.

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Old Nov 12, 2007, 05:24 PM
Account closed
Joined Oct 2002
35,016 Posts
Watering at the mouth!!! SUPER JOB Gerry!!!
guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Nov 12, 2007, 05:25 PM
Account closed
Joined Oct 2002
35,016 Posts
Now I can see how much WORK is involved in building a scratch built and paying attention to SCALE effects!!!!
guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Nov 12, 2007, 05:26 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Next comes rough snading using 100 grit sandpaper...followed by fine sanding using 400 grit.

Final sanding on the fairings is complete. See photos.

Next will be making balsa airfoil struts to dress up the exposed wire assembly between the fairings.

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Old Nov 12, 2007, 05:27 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Quote:
Originally Posted by simano
Next comes rough snading
I meant "sanding"...

Carlos...right on...I got the momentum it's great!!!..

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Old Aug 09, 2008, 06:43 PM
Jungmeister 55
simano's Avatar
Orlando Herndon, Florida, United States
Joined Sep 2002
3,453 Posts
Build resumes...again!!!!!!...

I'm bad....real bad. I mean here I have a unique model, one that I'm passionate about...and I kept putting this project off again and again....

Well, I resumed today and I'm gonna make a super effort to not let go again...until it flies!!!!...and judging by these photos I shot today about the progress, I'm all psyched again so, this should be it!!!!...

Today I fixed the top wing and aligned the strut mounting locations so, it is now ready to cover!!!!...yeah!!!

Notice the covered landing gear. I'm using ECONOCOTE on this one.

I will be covering the top wing tonight...

Gerry.
simano is offline Find More Posts by simano
Reply With Quote
Old Aug 09, 2008, 07:30 PM
Neophyte hacker
portablevcb's Avatar
Albuquerque, NM USA
Joined Sep 2003
15,648 Posts
Gerry,

Good things come to those who wait

I have the same kind of project, actually two of them. One is now being framed up and I'll have the parts cut for the other one this week. The first is only a year old, the second is a three year long design!

Hang in there, you know it'll be worth it.

charlie
portablevcb is offline Find More Posts by portablevcb
Reply With Quote
Old Aug 09, 2008, 07:41 PM
Account closed
Joined Oct 2002
35,016 Posts
Charlie,

You have no idea how hard it has been for me and Gerry's other RC Flying Buddies to encourage this very nice project to resume.

I am pretty sure Gerry would not mind a bit that what hit the trigger again was him winning a bid at eBay of a historical booklet of the Bucker Jungmeister / Jungmann.

This project will be a very unique RC model as no one has one except those that were fortunate to get the PICA Kit or make it out of plans like Gerry did.

I am so happy for Gerry as he may not realize today but, when he get this wonder model in the air, he will be saying why on Earth did I not finish sooner!!!
guapoman2000 is offline Find More Posts by guapoman2000
Reply With Quote
Old Aug 09, 2008, 09:02 PM
Registered User
St. James, NY Long Island
Joined Jul 2002
100 Posts
Hi, I am currently updating my Aeronaut Bucker Jungmeister. I will take out the Nmh pack with 13 cells and replace it with a 4 cell 3700 Lipo. I will replace the Phasor 45/3 with a 610 KV Chinese Outrunner. So far I am saving 12 oz. The Lipo fits perfectly in the battery box. My biggest hope is that it will balance. Ray
Ray Juschkus is offline Find More Posts by Ray Juschkus
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Robbe Bucker Jungmeister Parkflyer - Worth trying?? sam2000pres Foamies (Kits) 9 Sep 25, 2007 02:57 PM
Robbe Bucker Jungmeister? GiantScale Parkflyers 5 Nov 25, 2004 07:30 PM
Yippee! Scratch built 43" Bucker Jungmeister guapoman2000 Parkflyers 0 Sep 07, 2004 07:47 AM
WANTED: PICA Bucker Jungmeister 60" span kit simano Aircraft - Fuel - Airplanes (FS/W) 0 Apr 11, 2004 12:05 PM
Bucker Jungmeister or Heinkel He51 ? KOMET 44 Scale Kit/Scratch Built 18 Aug 24, 2002 07:13 PM