 |
 |
 |
|
Nov 09, 2012, 09:16 PM
|
|
|
United States, MS, Tupelo
Joined Jun 2012
178 Posts
|
KK2.0 Yaw Problem
I flew earlier today and forgot to plug in my lipo alarm, and accidently flew until something lost power. Luckily I didn't crash, but now I have almost no yaw control. I can't figure out why. I have calibrated the sensors, ran the sensor test, ran the receiver test, and reset the throttle limit for the escs. The motors seem to have full power. Motor layout is correct. I don't know what else to check. Did I break something by flying to cutoff?
Edit - when I say no yaw authority I mean it spins like crazy right after takeoff. |
|
Last edited by installerblizz; Nov 09, 2012 at 09:22 PM.
|
|
|
|
Nov 09, 2012, 09:40 PM
|
|
|
United States, NY, Shelter Island
Joined May 2011
713 Posts
|
What frame, type of multi do you have? Tri, quad, hexa?
Did you disconnect anything after the low voltage cut off? H |
|
|
|
Nov 09, 2012, 11:37 PM
|
|
|
United States, MS, Tupelo
Joined Jun 2012
178 Posts
|
Diy quad. Turnigy 6A's. I discomnected the batt immediately. Why?
|
|
|
|
|
Nov 10, 2012, 02:42 AM
|
||
|
Australia, VIC, Frankston
Joined Jul 2012
330 Posts
|
Quote:
|
|
|
|
|
|
|
Nov 10, 2012, 04:26 AM
|
|
New Brunswick, Canada
Joined Nov 2004
1,633 Posts
|
Odd issue. How's your RC rudder trim? Maybe it got bumped and you didn't notice?
|
|
|
|
|
Nov 10, 2012, 09:50 AM
|
|
|
United States, MS, Tupelo
Joined Jun 2012
178 Posts
|
Kk2 was bought used sans buzzer. All trims are at zero. It spins one way and if I fight it I can make it stop for a second but then it spins the other direction. Also, before lift off I can scoot it along the floor as desired, so everything is hooked up right. Before this started yaw became coupled with roll getting progressively worse. Maybe a motor is buurning out?
|
|
|
|
|
Nov 10, 2012, 12:32 PM
|
|
|
United States, KY, Springfield
Joined Jul 2011
1,202 Posts
|
have you tried a factory reset? write down all your settings before you reset if you decide to try it, might not work but as it sounds couldn't make it any worse ether...
|
|
|
|
|
Nov 10, 2012, 12:40 PM
|
|
|
United States, MS, Tupelo
Joined Jun 2012
178 Posts
|
Z gyro now reads 0 and won't calibrate. I don't see factory reset in the menu.
Edit: Bad gyro. If I gently press down on the gyro it works momentarily. Guess I need a new board. |
|
|
Last edited by installerblizz; Nov 10, 2012 at 02:49 PM.
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Help! brand new kk2, tricopter setup; error no yaw input | Brian Courtice | Multirotor Talk | 2 | Oct 27, 2012 08:29 PM |
| Discussion KK2 Board Yaw Gyro reversed | Bobdj | Multirotor Talk | 3 | Oct 12, 2012 10:00 AM |
| Question Problem with KK2.0 Board in Self-level mode | p.a.h. | Multirotor Electronics | 2 | Aug 24, 2012 08:40 PM |
| Discussion Y6 and Yaw P and I settings on kk2.0 board | Nexus21214 | Multirotor Talk | 0 | Aug 22, 2012 03:33 PM |
| Discussion Yaw issue with 4.0 upgrade on x8 and Y6 | tahoelight | Hoverfly Technologies | 11 | May 04, 2012 01:37 AM |
|
|