Here you go. Cannot find any in EU.

http://www.rcrus.com/Camera-Mount-Gi...Parts-SPGM-018

http://bradatech.com/xPedRobo/shop/i...roducts_id=113

Originally Posted by EndOfDays

Hello,

Do you know where I can get this part to mount on the lens of a Z15 (Sony Nex)?

best regards

Ferdinand

Ferdinand,

Have you tried:

http://www.coollcd.com/

They carry a ton of rigging stuff.............

Originally Posted by redridinghood

Here you go. Cannot find any in EU.

http://www.rcrus.com/Camera-Mount-Gi...Parts-SPGM-018

http://bradatech.com/xPedRobo/shop/i...roducts_id=113

+1 Bradatech.com - these guys are great, shipped me an esc yesterday at 4pm and got it at 1030am this morning!

Originally Posted by EndOfDays

Hello,

Do you know where I can get this part to mount on the lens of a Z15 (Sony Nex)?



best regards

Ferdinand

Did you try Digitech.nl ? They service the Z15 so they might have spares even if they are not listed in the webshop...

Originally Posted by EndOfDays

Hello,

Do you know where I can get this part to mount on the lens of a Z15 (Sony Nex)?



best regards

Ferdinand

DJI sell this separetly as spares, you can order this to a dealer.

Thank you for your help, and the shop links, I will bookmark them for the future. Found already one, offered by a really kind member of this forum who has one spare.

Thanks and best regards

Ferdinand

Originally Posted by EndOfDays

Thank you for your help, and the shop links, I will bookmark them for the future. Found already one, offered by a really kind member of this forum who has one spare.

Thanks and best regards

Ferdinand

Of you need some zen parts later on, you have en link here. ;-)

http://aerialmediapros.com/store/ind...-parts-c-25_73

Originally Posted by Jelico

Another question...


Do you know if I Can use all 14 channels of my 8FG with the included SBUS Futaba R6208SB receiver?

The Wookong supports S-Bus so in theory its possible right? Or am I missing something and need to buy a 14 channel receiver for it.

Or is that receiver limited to 8 channels whether you use it as an Sbus receiver or not.

Really appreciate your advise here- I need to be able to run 13 channels so working out what I need to to to make that happen.

After a bit of research, it looks like I have to buy a new receiver to get all 14 channels out of my 8FG (and use one receiver). One thing that I was wondering, is it possible to use my 8 channel receiver for the S800/Wooking, and then pair a second Faast receiver to the same transmitter? Then just run the extra channels of that some how?

I saw this link (http://www.multirotorforums.com/show...AZA-8-channels) that seem to indicate that this can work - it would go something like this:

Main receiver:
1- Aileron
2-Elevator
3- Throttle
4-Rudder
5- FC mode (atti, man, GPS etc)
6-FC Return to home
7- IOC switch

Second Faast receiver:
1- Zenmuse Pan
2- Zenmuse tilt
3- Zenmuse roll
4- Zenmuse Shutter
5-Zenmuse Mode
6-iOSD
7-AUX

Basically.. I am trying to figure out the easiest way to run my S800/WKM/Zenmuse with most of the above functions on my 8FG. All and any advice is appreciated.. Cheers!

Hi Guys!!

I am setting up my S800 + Zenmuse to be the easiest to film with. My setup is for 2 man operation and we have two cameras on it (FPV for pilot and Zenmuse), both connected through DJI OSD and one VTX. We are only using the Zenmuse output to get the filming image all the time but for the pilot would be really useful to have separated signals to switch between cameras and not blind the cameraman.

On the ground each operator has a monitor, both connected to one Diversity. I was planning to buy another Diversity receiver but I'd like to know if I will get the same problem switching cameras and blinding my cameraman.

My quiestion is, do I need two Video TX on my Hexa to choose between cameras or just buying another Diversity Receiver I will be able to choose between cameras while the cameraman allways watches the Zenmuse Output?

Thanks in advance!!!!

Best Regards from Mallorca, Spain.

Yes you need a sperate video transmitter on a different frequency to get the two video feeds. Only other way to do it is run a camera switcher but again you'll cut off either your pilot or camera operator feed when you switch.

@Petro

You need two Video TX, and two (optional Diversity) Receivers. I choose (to be on the save side) LHCP Antennas for the one Video channel and RHCP for the other.

I have already setup such a system:

https://vimeo.com/58822034

best regards

Ferdinand

Originally Posted by EndOfDays

@Petro

You need two Video TX, and two (optional Diversity) Receivers. I choose (to be on the save side) LHCP Antennas for the one Video channel and RHCP for the other.

I have already setup such a system:



best regards

Ferdinand

Wow Ferdinand that's an impressive set-up there!!

Originally Posted by EndOfDays

@Petro

You need two Video TX, and two (optional Diversity) Receivers. I choose (to be on the save side) LHCP Antennas for the one Video channel and RHCP for the other.

I have already setup such a system:



best regards

Ferdinand

I like your landing gear bench testing fail safe invention.

@topgearuk
Thanks, most of the job is just to setup this hobbyking buddy-box correctly, then the rest is easy (beside the hundreds of meter wire you have to install )

@hexa
Yeah, I will probably call it LLTBP 1.0 (Landing Legs Testing Bench Protection)

best regard

Ferdinand

Originally Posted by topgearuk

Wow Ferdinand that's an impressive set-up there!!

i have a similar set up with pilot having the choice of camera and the payload operator having the gimbal only output,
you will need a proper video splitter that boost the signal or you will run into transmission problems