Thanks yust made my upgrade.

Ps this is a very nice TX

Grtz Ed

Originally Posted by dkfuji

Nice. Got a question for you though. Is your scroll button on the right functioning like it should? My first version has the button programmed where pushing up decreases the value (opposite of what it should be). Is this the case with yours?

Scroll buttons seem to be functioning properly. Push up, cursor scrolls up. Push down number decreases, etc.

My free radio (well, 35.85USD for shipping) is due on Tuesday. I'm thinking I might try to take Wednesday off if the weather is nice to give it a good run through.

Cheers!
Randall

Just got mine today. Is anyone using a lipo with theire devo tx?
If so, what's working? What do you recommend?

I tested the Devo10 and this is a winner.

Im using lipos its the same i used in my 2801Pro(2200mah 11.1v 15C).

So the same feel as the 2801Pro(they using the same casing)

Without manual its a very easy to understand interface.

Setting up a heli is so easy.

The sticks are a much better feel than on the 2801Pro(ball bearings)

So what can i say more Walkera made a very nice TX in one word a winner for the money

For sombody looking for a TX on a budget dont hesitate and buy the Devo10 you wont regret it.

Grts Ed

Originally Posted by brianos007

I tested the Devo10 and this is a winner.
Im using lipos its the same i used in my 2801Pro(2200mah 11.1v 15C).
So the same feel as the 2801Pro(they using the same casing)
Without manual its a very easy to understand interface.
Setting up a heli is so easy.
The sticks are a much better feel than on the 2801Pro(ball bearings)
So what can i say more Walkera made a very nice TX in one word a winner for the money
For sombody looking for a TX on a budget dont hesitate and buy the Devo10 you wont regret it.

Grts Ed

Thanks for the report!
Can it bind with your RX1201?

Originally Posted by FDR_

Thanks for the report!
Can it bind with your RX1201?

I just tryed and it s not binding with the RX1201.

Binding RX801 with the Devo10 is no problem.

Grtz Ed

Originally Posted by brianos007

I just tryed and it s not binding with the RX1201.

Binding RX801 with the Devo10 is no problem.

Grtz Ed

Thank you!
Just as I thought...

I shot a quick vid this morning (before I went out to fly my Mini) showing how really simple this Tx is to navigate around the settings. I also have the 10 channel Rx installed in my new Trex 500Pro and it is working perfectly. IMO, this is a really nice Tx for the money.

Walkera Devo 10 Review - New Gun Metal Black from www.Wowhobbies.com (9 min 10 sec)

Originally Posted by dkfuji

I shot a quick vid this morning (before I went out to fly my Mini) showing how really simple this Tx is to navigate around the settings. I also have the 10 channel Rx installed in my new Trex 500Pro and it is working perfectly. IMO, this is a really nice Tx for the money.

http://www.youtube.com/watch?v=7bB0LVuxEig

+1

Do you have an idea of the range of the 10mw.

All my other TX are 100mw.

Grtz Ed

How is this compared to Turnigy 9x? I realize if you add the backlight mod, programming cable/board for flashing the firmware and nicer FrSky radio module, the price of a fully patched Turnigy 9x might be close to the Devo 10. Thinking should I just sell the Turningy 9x that just arrived and get this one

I can't wait until the Devo's can support dsm2/dsmx.

Originally Posted by itsmillertime

I can't wait until the Devo's can support dsm2/dsmx.

Will they?

You tell me. You guys that are smarter than me are working on it aren't you?

Just received my "Give-away" Devo10....

Will test it during the Easter Weekend (hopefully the weather is fair).

The Unit came with a RX1002 Receiver.

Other than the Devo8(s) this unit runs on 8 AA Batteries.

Letīs see if Telemetry (with my MX400) works as fine as with the Devo8.

More later.

SAM