Yea, stock firmware does AH too. No idea how good it is, but it works in MWC as well.
You still need to solder the sensor though, or attach some breakout. Anyway, better than endless "vendor" chasing bugs on this hardware

thanks

Hi guys!

Before the TMF upgrade here is a little video with my new GoPro

Vol à la mine! (3 min 33 sec)

Cheers

Hi all, please post her again wich Escs you use. And wich Setup for them. as Infofor all other.
I use TURBO JET 30A esc, its like Super Simple esc, Like nothing to set up.
I tested them hovering as Quadro, they Shut Off at 10.3 Volt - 2200mah 3S Turnigy LIPO.
So my next is a LIPO Warner from http://www.lipoblitzer.de/. With Power LED.
SET at 10.7 V - three fast Flash - ALARM Landing now.

And Guys, I think it is Time for a V6 Frame like ?? will offer.
Have a Look here . http://www.rcgroups.com/forums/showp...15&postcount=1

Only a small Problem is , there is a Patent in Germany for a Frame Like this.
But make your own can no one forbidden, for Privat use.
Mike RCHHB

Wow nice frame! I like it!

Originally Posted by Rc Heli Halle

Hi all, please post her again wich Escs you use. And wich Setup for them. as Infofor all other.
I use TURBO JET 30A esc, its like Super Simple esc, Like nothing to set up.
I tested them hovering as Quadro, they Shut Off at 10.3 Volt - 2200mah 3S Turnigy LIPO.
So my next is a LIPO Warner from http://www.lipoblitzer.de/. With Power LED.
SET at 10.7 V - three fast Flash - ALARM Landing now.

And Guys, I think it is Time for a V6 Frame like ?? will offer.
Have a Look here . http://www.rcgroups.com/forums/showp...15&postcount=1

Only a small Problem is , there is a Patent in Germany for a Frame Like this.
But make your own can no one forbidden, for Privat use.
Mike RCHHB

Hey quick question here, about to finish my hexa and need to do the throttle calibration on my PLUSH 40 esc's, can this be done while the esc's are pluggin the aq fc or I need to do it manually ?

Do it manually, with ESC connected the Rx Throtle channel.

Originally Posted by timecop

$35 FreeFlight with MultiWii firmware outflies this board by both features and price.

Closed source solutions end up fading into obscurity sooner or later.

fully agree!

Well just did all of them, one by one but I've got one esc that doesn't want to enter throttle calibration mode. I turn on the tx, give full throttle then plug the lipo and all I hear is one bip then the motor goes WOT !!??? wth$ !?

Originally Posted by flitelab

Do it manually, with ESC connected the Rx Throtle channel.

Iīm having problem setting up the Turnigy 9X with this controller.

I tried reversed channels 1-4 but it didnīt worked.

How do i do to setup this radio?

Originally Posted by FAST

Iīm having problem setting up the Turnigy 9X with this controller.

I tried reversed channels 1-4 but it didnīt worked.

How do i do to setup this radio?

You should using PC tool to see joystick scrollbar.....
if the scrollbar moving direction is the same with your RC stick then you are find a correct setting
of course make sure your receiver output PWM range is normal ( 1ms~2ms high)

Originally Posted by FAST

Iīm having problem setting up the Turnigy 9X with this controller.

I tried reversed channels 1-4 but it didnīt worked.

How do i do to setup this radio?

Set your throttle channel to 90% before calibrate your ESCs and leave it to 90% for aq50d pro

Originally Posted by pietronet

Hi guys!

Before the TMF upgrade here is a little video with my new GoPro

http://youtu.be/bu9FitMr3lg

Cheers

good job,man.

carbon fiber props
1045:

1245:

Hi , now i mount my DIY Cam mount on my AQ50pro, Not connect to FC for Gimbal Servos. Because will use next for FPV. Nick servo connect to CH5 RX, for adjustment up / down Cam. Let settle Quadro 5min outside for Temp climate the Fc. I use for this heavy Quadro , all are 1,6 kg togehter, two row 2200maH Turnigy Lipos, after Video Flight Lipo Tester says 11,7 V. I think enough for a 4min Flight more. AQ nice , stable . No drift ? I fly by sensitive Hands, so I regulate it to be gone. Sorry , first would to be get higher, but i am anxious in middle of Berlin and with such so much People around.
See us at LANDKAMP.de
Best Regards to all AQ Pilots and happy Holidays dear mahui.
Mike RCHHB
http://youtu.be/hXvSv1IzAlk

And yes I know, better cam and better SD. LOL