Originally Posted by thepelell

that's cool... fast descent without wobble, i can't do that either with my multiwii or the crap fy91; they will both wobble badly if i attempt a rapid vertical descent like you did...
can't wait to get mine...

Yes it does fast decent better than my other quads, all with no tuning. But I think it is in part due to the build as well as the controller board. Very impressed with it so far espeically due to the simple setup process.

Originally Posted by thepelell

that's cool... fast descent without wobble, i can't do that either with my multiwii or the crap fy91; they will both wobble badly if i attempt a rapid vertical descent like you did...
can't wait to get mine...

Hi,
thank you for the last tip to balance motor and props in once time.
Now i have test firmware 1.9 and 3 blade GWS(balanced) and this are the results.With 1.7 and 2 blade props i also have hat problems with whobble in fast descending.
But now is fine, the only thing with 1.9 was that the first ver. from 8.11 have a IC2 problem, and so 2 times 1 of the motor stopped in fly and i have broken 2 props. Now i have upload the version from 12.11 and i wait for new props and then i upload the results.

Saluti

Lunarlander Halle (2 min 28 sec)

Hello
testing TMF pro on a small frame 27cm called Evil fly I used to fly with Aq50 but pro board is definitly more stable.
Descent is very clean, no wobbling at all. Flew during 14 minutes (7minutes on vidéo)
Filming while sun was getting down that made some nice shots. Definitly need to install some leds for much convenience
cheers

Evil©Fly DIABLO AQ50 PRO INSIDE.mov (7 min 7 sec)

Originally Posted by C team MOD

Hello
testing TMF pro on a small frame 27cm called Evil fly I used to fly with Aq50 but pro board is definitly more stable.
Descent is very clean, no wobbling at all. Flew during 14 minutes (7minutes on vidéo)
Filming while sun was getting down that made some nice shots. Definitly need to install some leds for much convenience
cheers

http://www.youtube.com/watch?v=GaeOr...e_gdata_player

cool,very good.

still cannot get the AD50Q to connect to my PC ...
here is a screenshot ...
is there anything that i am supposed to do with the PORT SETTINGS ??

Originally Posted by QiW

still cannot get the AD50Q to connect to my PC ...
here is a screenshot ...
is there anything that i am supposed to do with the PORT SETTINGS ??

1. open tool with administrator privileges....
2. close windows UAC......

ahhh ... ok
got it ...
needs administrative privileges to run
its working now ... thanks

few more questions ...
i flew my AD50Q yesterday .. it levels out too fast/very abruptly when i release the aileron/elevator sticks ... if i wanted it to level out at a much slower rate .. what do i adjust in the MENU ?
also .. my altitude holding is not very good .. 530mm X frame size with 10x4.5 800kv motors ... what do i adjust for this ?

thanks again

Originally Posted by QiW

ahhh ... ok
got it ...
needs administrative privileges to run
its working now ... thanks

few more questions ...
i flew my AD50Q yesterday .. it levels out too fast/very abruptly when i release the aileron/elevator sticks ... if i wanted it to level out at a much slower rate .. what do i adjust in the MENU ?
also .. my altitude holding is not very good .. 530mm X frame size with 10x4.5 800kv motors ... what do i adjust for this ?

thanks again

1. try to adjustment the "AGain"...maybe lower

2. about altitude.. try to adjustment your transmitter throttle curve

Originally Posted by jimmytseng

1. try to adjustment the "AGain"...maybe lower

2. about altitude.. try to adjustment your transmitter throttle curve

ok ... will try those out too
AGain is via PC ... lowered from 7.8 (default) to 7.0
will see how it flies once i reconstruct a new frame (crashed yesterday) .. LOL

Error

Originally Posted by QiW

AGain is via PC ... lowered from 7.8 (default) to 7.0

If I were you, I would have tried the pot before.

Originally Posted by warthox

- decreased stabilization strentgh with the pot because of some oszilations during first flight.

board arrived today. 30 mins from saying goodbye to postman, i had a big smile on my face and my battle quad was up in the air, very stable, and very good response. Auto level is best i have used up to now.. It is not invasive and doesn't interrupt pilot stick input like fy91 does, and has a nice natural feel, unlike the multiwii autolevel that i have never liked (even if from first test 1.9 seems better).
No problem with rapid descents, just like in videos posted above by other users, i have never been able to come down that quickly without worries...
wow... and all i had to do was lower a bit gain because in default it had oscillations...
very very cool.. can't wait to do more tests tomorrow.
now i have to celebrate...

Originally Posted by Mortimer

If I were you, I would have tried the pot before.

well ... actually i did try that pot 1st
from about 40% to 60-70% ... no oscillations but it still auto levels just as fast
now that i have lowered the AGain ... i have to chance to try it out yet (crashed the quad on sunday)

Originally Posted by jimmytseng

Hi guys
I found a new firmware for TMF Pro(AQ50d Pro)
seems to be remove a circuit resistance....(remove R21 short circuit R19)
then upload new firmware for 6G accelerometer

http://www.youtube.com/watch?v=vZjiI...ature=youtu.be

(V1.2 Improve the gyro temperature drift correction and dynamic flight performance)

Just upgraded mine now

is the hardware modification necessary for firmware update or can you just put new firmware ? i still don't understand what 6g mod is usefull for...

up to now i am very pleased with how the board works. Very simple to setup and pleasant to fly. Auto level is not invasive, even if you release stick quickly, it doesn't try to halt immediately, this is very useful for filming.