Hi,

Could anyone give me detailed instructions on how to set up a seperate switch for RTH on a Futaba 14MZ?

Merry Christmas!

Hi all!

Well I buy and HEXA combo from CNCHelicopter to work with DJI wk-m and I mounted here! I manual mode the copter fly amazing, but in ATTI or GPS ATTI he unstable an little, in ATTI GPS he stay in an 2m diameter but probably need some GAINS adjust!

I would know if anyone have this smae combo and what GAINS do you use?

Thank you

Lucas Munhoz

Its Xmas time and we are offering $10 off coupon code (basically it gets you free 2 day shipping on any purchase of any products)

Coupon code 10off

Happy Holidays.
DJIUSA.com

Originally Posted by Rkopf

Hi,

Could anyone give me detailed instructions on how to set up a seperate switch for RTH on a Futaba 14MZ?

Merry Christmas!

Richard I wish I could help you on the detail instructions for that TX. Which by the way is a great TX.

Basically, you have to do a mix so when you flip the switch it puts the control mode channel in the Fail Safe Highlighted area when viewing the control mode switch travel in the TX calibration screen.

Also, any purchase of WKM gets the free DJI Flame Wheel 450 frame.

Originally Posted by RTRyder

The adaptors from Electricwingman are the actual Graupner part, I usually just put them in and then file down to fit. The aluminum ones tend to get stuck on the prop adaptor when you take the prop off and its really easy to mangle them trying to remove them if an extra tight fit.

I haven't had any problems with the aluminum ones, I even use them on the APC props.

Originally Posted by slidins15

Hi all,
I have my wookong m setup on a rusty's frame octo with ntm prop drive 35-36 910kv motors and turnigy plush 30a escs. It flies great and I have been tinkering with settings and setups to get it just how i like it.

I have the IMU shielded with foil tape (except the baro sensor), and the plate between my electronics and my gps is covered with foil tape too. THe gps is on the longest pole and I've tried to keep it as far away from all electronics as possible (it has at least 20cm from any electonics)

The problem I'm having is I get full gps lock within 2 or so mins, and gps holds great in the air. However a few minutes into flying, without fail the gps drops out and I get three red flashes. It happens all the time, whether close to the ground or high in the air.
If I bring the octo down and restart it, the gps locks almost straight away for a few minutes and then drops again.

I'm not getting white flashes, have tried mounting gps pole foam tape in case it was vibrations and still no difference.

Can anyone point me in the direction of what is going wrong? It is getting so frustrating because I'm dying to try out RTH and auto land and I need it to be reliable.

It sounds like the gps is being hurt when the motors run. Either power wires to or from the esc or emi from the esc is killing the gps. Try tying it down or removing the props and running the motors. If the problem repeats it is motor related. The only solution to emi is sheilding or distance.

Post some pictures of you instalation so we can see where everything is mounted.

RC Santa Claus 2011 (2 min 1 sec)

Very Nice. Merry Christmas to you and your family.

lou

Originally Posted by rerazor

Its Xmas time and we are offering $10 off coupon code (basically it gets you free 2 day shipping on any purchase of any products)

Coupon code 10off

Happy Holidays.
DJIUSA.com

Robert,
Are you going to get in the 900mhz links and the Click and go?
That's my next step...

Bill Davenport
AMA 28141

Originally Posted by justiina

http://youtu.be/8JrfJaz6HQw

Wow justiina, that was very risky, great idea. What are you going to do for his birthday, hang a pinata from your quad and let his friend beat the candy out of it?
Just wondering.

I thought it was very nice too. Looked like a lot of fun.

Merry Christmas

Hey guys thought I would show a short promo clip from a couple of day ago. The Y-6 and the WKM are working well but getting things sorted out and still have a few issues to work out but getting there.
Hope you all have a Very Merry Christmas.

Michael64

Apache Pass A View from Above December 2011.mpg (3 min 1 sec)

Originally Posted by justiina

http://youtu.be/8JrfJaz6HQw

Nice!! I loved !!!

Merry Christmas!! for all

Merry Christmas ........
Happy Holidays ........
Happy Hanukkah .......

To all ...