SMALL - espritmodel.com SMALL - Telemetry SMALL - Radio
Reply
Thread Tools
Old Aug 03, 2011, 03:11 PM
Registered User
RcToysFinder's Avatar
Zuerich Switzerland
Joined Nov 2010
14 Posts
Help!
Soldering Esc`s for Quadro/Hexa/Octo..

Hi together

I need your help. Please let me know how you solder the ecs`s together.
If you have 4 or more Esc`s it is very tricky. Please show me how you do this solder job or any other options

Thx for your answers
RcToysFinder is offline Find More Posts by RcToysFinder
Last edited by RcToysFinder; Aug 03, 2011 at 03:36 PM.
Reply With Quote
Sign up now
to remove ads between posts
Old Aug 03, 2011, 04:23 PM
OS Sponsor
kinderkram's Avatar
Germany, NRW, Dusseldorf
Joined Jun 2010
5,225 Posts
Quote:
Originally Posted by RcToysFinder View Post
Hi together

I need your help. Please let me know how you solder the ecs`s together.
If you have 4 or more Esc`s it is very tricky. Please show me how you do this solder job or any other options

Thx for your answers
You could go for a power distribution:
http://www.flyduino.com/product_info...er-board.html/
kinderkram is offline Find More Posts by kinderkram
RCG Plus Member
Reply With Quote
Old Aug 03, 2011, 05:14 PM
Registered User
United States, TX, Thrall
Joined Feb 2010
1,192 Posts
kinderkram
Do you by chance have any photos of how you connected the wiring this board I ordered two of them and not sure how is the best way to connect the ESC wires and battery leads I know solder but what about connectors any advice what help alot. I have been using Mactadpole setup with the deans and solid 12 ga. copper wire.

Michael64

Michael64
Michael64 is offline Find More Posts by Michael64
Reply With Quote
Old Aug 03, 2011, 05:23 PM
Registered User
iota's Avatar
Germany
Joined Nov 2010
6 Posts
Some time ago i have done this: see below

But these are tiny Turnigy Plush 6. They are converted to I2C-Control and equipped with Quax-Software

Juergen
iota is offline Find More Posts by iota
Reply With Quote
Old Aug 04, 2011, 03:56 PM
Registered User
RcToysFinder's Avatar
Zuerich Switzerland
Joined Nov 2010
14 Posts
Thx for your answers.
I think i must made two wire rings one with the + and one with - pole.
Then i cut 6 pieces out and solder the esc wires to them.

To kinderkram:
How many amps does this boards can handle ? I will use it for a hexa with 6x 60A on 4S.
Do you know the dimensions ?
RcToysFinder is offline Find More Posts by RcToysFinder
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Poll Quad X8, Y6, Hexa, Octo? Rusty's Rev-8 Frame decision daign Multirotor Talk 2 Jul 20, 2011 09:28 PM
Help! Measurements or CAD for MK hexa and octo mounting points for electronics? tabbytabb Multirotor Talk 5 Feb 27, 2011 01:36 PM
Discussion MK Quadro XL or Hexa Ripper78 Multirotor Talk 9 Feb 23, 2011 12:56 PM
Discussion AP Hexa or Octo? What gives you the best stabilisation? Voguna Multirotor Talk 7 Feb 09, 2011 06:35 AM
Discussion "mkTR" Hexa/Octo camera gimbal Photoship One Multirotor Talk 0 May 27, 2010 02:00 PM