thnaks max 5", tihs version is Multiwii dedicated i like the fact to integrate all multiwii necessary in tihs tight space and the people know it well and have some components, but....maybe later.

quadframes are back in stock only the spider needs a bit, a new gps will be stocked too on weekend.

hi paul , the frame looks good .will you offer motors for the flydumini as well or can you tell us which motors norf uses ?

Hy Paul, which Motor is ok for the flydumini

Abmessung Gewicht U/Volt Zellen Luftschraube 1/min Strom Schub
ROXXY BL-Outrunner 1815/17 18 x 21 mm 13g 2900 2 5,0 x 3,0 GWS-HD 13241 4,6 A 162 g
ROXXY BL-Outrunner 1815/25 18 x 21 mm 13g 2000 2 5,0 x 3,0 GWS-HD 10487 2,1 A 101 g
ROXXY BL Outrunner 1820/10 18 x 26 mm 18g 2520 2 5,0 x 3,0 GWS-HD 13646 4,3 172 g
ROXXY BL Outrunner 1820/12 18 x 26 mm 18g 2120 2 5,0 x 3,0 GWS-HD 12173 3,1 137 g
ROXXY BL Outrunner 2216/18 22 x 23 mm 19g 2570 2 5,0 x 3,0 GWS-HD 12375 3,1 142 g

Michael

der erste hört sich gut an wobei der ne ziemlich hohe drehzahl/V hat

i like the fiorst one from this list .... or maybe the second one since the kV is lower


what do you guys think ?

laut Lehrbuch wohl
ROXXY BL Outrunner 1820/12 18 x 26 mm 18g 2120 2 5,0 x 3,0 GWS-HD 12173 3,1 137 g
for 5" props.
Norf uses A1510, can stock them no problem, but we still have to test, next time i bulid a black mini i will try Hextronik 10g, will see, something in this range will fit.
Roxxy is for sure a good choice, but a bit too pricey for most i think.

Hmmm ... they're small, light and they're Roxxys.
But 30 Euros each for a Mini indoor flyer?

I have some cheap Hextroniks laying around. Think I'll give them a try...



http://www.hobbyking.com/hobbyking/s...er_1300kv.html

whick kv rating will you choose with the 10g hextronik ? 1500? 1800? 2000?

Originally Posted by M4d_D

whick kv rating will you choose with the 10g hextronik ? 1500? 1800? 2000?

I think HK only has 2000kV/10gr, 1700kV/16gr, 1300kV/24gr

2000 as i think you will need it for 5" and 2S but the best setup still have to be found i think.
Norbert if it only 1300kv you may should go at least 3s i think and even that will be a bit low for 5".

i looked at the HK homepage and i think these motors might work....

please have a look at them :

• http://www.hobbyking.com/hobbyking/s...r%5FMotor.html
• http://www.hobbyking.com/hobbyking/s...%5F2000kv.html
• http://www.hobbyking.com/hobbyking/s...%5F10g%5F.html
• http://www.hobbyking.com/hobbyking/s...%5F1850Kv.html
• http://www.hobbyking.com/hobbyking/s...idProduct=8476
• http://www.hobbyking.com/hobbyking/s...%5F1500kv.html
  

the turnigy 10g and the hextronik 10g motors look quite similar.... you are right , there is only a 2000kv hextronik 10g

the 24g 1300kv work great on 3s with 8x4 ( 8x4.5 is too much ) but for 5" there are other higher kv motors ... i dont think the 1300kv will work with 5" props

Warthox will try the Turnigy 1811 2000kV (second in your list), Paul the HT 10g 2000kV and I'll try the HT 24g 1300kV.
We'll have a good comparison then. I'll take some 2s lipos first.
My poor plants need time for recreation.

looking forward to your results

Originally Posted by M4d_D

looking forward to your results

Me too!

Guess I'll have to wait a bit until I have all parts here.
Especially 5" props are not easy to find...

HK has some 5" props but i dont know if they are in stock