-


Transmitter Setup Guide List


All these setup guides and more of them are on my web site.
The setup guides are much easier to navigate through on my site.
Models for the deviation firmware are posted on my site, they are not posted here.

http://www.rcproreviews.com/




1. Walkera 4#3B and Walkera CB100

2. Walkera V100D01

3. Walkera V100D03

4. Walkera V100D08

5. Walkera 4G6

6. Walkera 4G6S

7. Walkera 4G6V

8. Walkera Genius CP V1/V2

9. Walkera Mini CP, Walkera Super CP

10. Walkera QR Ladybird V1/V2 , Walkera QR Infra X, QR Scorpion, QR Spacewalker

11. Walkera Super FP, Walkera Genius FP

12. Walkera Master CP

13. Walkera V120D02 - (For the RX2610V2 Receiver)

14. Walkera V120D02S - (For the RX2622-D Receiver)

15. Walkera V120D02S - (For the RX2622-V Receiver)

16. Walkera V120D02S V2 - (For the RX-2636H-D Receiver)

17. Walkera Hoten X

18. Blade mCPX V1

19. Blade mCPX V2

20. Blade Nano CP X

21. Blade CX2 and Blade CX3

22. Blade 130 X

23. Align T-Rex 250 SE/Pro and Align T-Rex 450 SA/SE

24. How to Videos for updating firmware and Import/Export Models

25. Walkera QR Ladybird, Hoten X, and QR Infra X using the Magic Cube MTC-01 - Walkera WK-2801 Pro Transmitter

26. Walkera Genius CP, Mini CP, Super CP using the Magic Cube MTC-01 - Walkera WK-2801 Pro Transmitter

27. Walkera QR X400

28. Walkera V450D01

29. Walkera V450D03

30. Walkera 4F200LM



Transmitter Setup Guide Index



1. Walkera 4#3B and Walkera CB100 - How to setup the TX for the RX2406C and RX2605A Receiver - Walkera WK-2801 Pro Transmitter.

http://www.rcgroups.com/forums/showp...96&postcount=5



2. Walkera V100D01 - How to setup the TX for the RX2441V Receiver - Walkera WK-2801 Pro Transmitter.

http://www.rcgroups.com/forums/showp...93&postcount=4



3. Walkera V100D03 - How to setup the TX for the RX2620V Receiver with 3-Axis Gyro - Walkera WK-2801 Pro Transmitter.

This also includes Justin Proud settings (ClubHeli's test pilot)

http://www.rcgroups.com/forums/showp...2&postcount=12



4. Walkera V100D08 - How to setup the TX for the RX2632V-D Receiver - Devo Transmitter

http://www.rcgroups.com/forums/showp...8&postcount=46



5. Walkera 4G6 - How to setup the TX for the RX2609 Receiver - Walkera WK-2801 Pro Transmitter.

http://www.rcgroups.com/forums/showp...30&postcount=3



6. Walkera 4G6S - How to setup the TX for the RX2610S Receiver with 3-Axis Gyro -Walkera WK-2801 Pro Transmitter.


* 3D Settings

* Beginner Settings

* Setup for the RX2610S and WK-2602 TX

http://www.rcgroups.com/forums/showp...63&postcount=2



7. Walkera 4G6V - How to setup the TX the for the RX2610V2 Receiver with 3-Axis Gyro - Walkera WK-2801 Pro Transmitter.

Post #1 below this Setup Guide Index.



8. Walkera Genius CP w/Devo RX - How to setup the TX for the RX2632V-D Receiver - Devo Transmitter.


* Beginner Settings for 3 axis mode

http://www.rcgroups.com/forums/showp...0&postcount=17


* Beginner Settings for 6 axis mode by bobepine

http://www.rcgroups.com/forums/showp...9&postcount=22


* Intermediate to Advanced Settings

http://www.rcgroups.com/forums/showp...2&postcount=15


* Finless Bob 3D settings

http://www.rcgroups.com/forums/showp...6&postcount=28



Walkera Genius CP w/2801 Pro RX - How to setup the TX for the RX2625H Receiver: WK2801 compatible - Walkera WK-2801 Pro Transmitter.


* Beginner Settings

http://www.rcgroups.com/forums/showp...3&postcount=16


* Normal Settings

http://www.rcgroups.com/forums/showp...0&postcount=24


* 3D Settings

* buildem336 3D Settings

http://www.rcgroups.com/forums/showp...0&postcount=14



Walkera Genius CP w/WK-2603 radio- How to setup the TX for the RX2625H Receiver.

http://www.rcgroups.com/forums/showp...6&postcount=23



9. Walkera Mini CP - How to setup the TX for the RX2632V-D Receiver - Devo Transmitter.

Walkera Super CP – How to setup the RX2645V-D – Devo Transmitter.


* Beginner Settings

http://www.rcgroups.com/forums/showp...0&postcount=21


* Intermediate to Advanced Settings

http://www.rcgroups.com/forums/showp...6&postcount=20


* 3D Settings

http://www.rcgroups.com/forums/showp...0&postcount=18


* My custom settings (Tom Z) for the Brushless Mini CP. Normal Flight/3D Flight.

http://www.rcgroups.com/forums/showp...9&postcount=25



10. Walkera QR Ladybird - How to setup the TX for the RX2634H-D Receiver - Devo Transmitter.

Walkera QR Infra X - How to setup the TX for the RX2457H-D Receiver- Devo Transmitter.

Walkera QR Scorpion- How to setup the TX for the RX2639H-D - Devo 10 Transmitter.

Walkera QR Spacewalker- How to setup the TX for theRX2640H-D - Devo 10 Transmitter.


http://www.rcgroups.com/forums/showp...3&postcount=29



11. Walkera Super FP - How to setup the TX for the RX2456V-D - Devo Transmitter.

Walkera Genius FP - How to setup the TX for the RX2625S-D – Devo Transmitter.


http://www.rcgroups.com/forums/showp...3&postcount=27



12. Walkera Master CP- How to setup the TX for the RX2637H-D Receiver - Devo Transmitter.


* Standard Settings

http://www.rcgroups.com/forums/showp...8&postcount=33


* Buildem336 (Manuel) 3D settings

http://www.rcgroups.com/forums/showp...9&postcount=64



13. Walkera V120D02 - How to setup the TX for the RX2610V2 Receiver - Walkera WK-2801 Pro Transmitter.

http://www.rcgroups.com/forums/showp...3&postcount=42


14. Walkera V120D02S - How to setup the TX for the RX2622-D Receiver - Devo Transmitter.

http://www.rcgroups.com/forums/showp...2&postcount=34



15. Walkera V120D02S - How to setup the TX for the RX2622-V Receiver - Walkera WK-2801 Pro Transmitter.

http://www.rcgroups.com/forums/showp...6&postcount=40



16. Walkera V120D02S V2 - How to setup the TX for the RX-2636H-D Receiver - Devo Transmitter.

http://www.rcgroups.com/forums/showp...4&postcount=45


* dkfuji 3D settings

http://www.rcgroups.com/forums/showp...9&postcount=72



17. Walkera Hoten X - How to setup the TX for the RX2635H-D Receiver - Devo Transmitter.

http://www.rcgroups.com/forums/showp...8&postcount=53



18. Blade mCPX V1 - How to setup the TX - Spektrum DX6I, DX7, and DX8 Transmitter.

JR 9303 transmitter settings. Use the DX7 or DX8 transmitter settings.

* Buildem336 (Manuel) 3D settings for the Spektrum DX7

* Beginner Settings

http://www.rcgroups.com/forums/showp...7&postcount=13


Futaba 9CHPS with an 8 channel Spectrum module.

Setup for the Eflight Blade mCPX V1 Helicopter - Futaba 10CHP settings with Spektrum module

Setup for the Eflight Blade mCPX V1 - JR 11x ZERO settings for MCPX

http://www.rcgroups.com/forums/showp...5&postcount=11



19. Blade mCPX V2 - How to setup the TX - Spektrum DX6I, DX7, and DX8 transmitter.

JR 9303 transmitter settings. Use the DX7 or DX8 transmitter settings.

* Buildem336 (Manuel) 3D settings for the Spektrum DX7

* Beginner Settings

JR 9303 settings for MCPX V2. Use the DX7 or DX8 settings.

http://www.rcgroups.com/forums/showp...1&postcount=19



20. Blade Nano CP X - Spektrum DX6I, DX7, DX7se, DX7s, DX8, and DX18 transmitter.

http://www.rcgroups.com/forums/showp...1&postcount=55



21. How to setup the TX for the Blade CX2 & Blade CX3 - Spektrum DX6I and DX7 transmitter.

http://www.rcgroups.com/forums/showp...6&postcount=59



22. How to setup the TX for the Blade 130 X - Spektrum DX6I and DX7 transmitter.

http://www.rcgroups.com/forums/showp...0&postcount=58



23. Align T-Rex 250 SE/Pro and Align T-Rex 450 SA/SE - Spektrum DX6I and DX7 Transmitter.


* Beginner settings

http://www.rcgroups.com/forums/showp...5&postcount=44


3D Settings

http://www.rcgroups.com/forums/showp...4&postcount=50



24. How to Videos

• How to Update the firmware on Devo Transmitters
• How to Update the Devo Receiver firmware
• How to Import/Export Models on Devo Transmitters
• How to Update the firmware on the RC Magic Cube MTC-01
• How to upgrade Devo TX Firmware to Deviation Firmware
• How to Import/Export Deviation Firmware Models

http://www.rcgroups.com/forums/showp...1&postcount=31



25. Setup for the Walkera QR Ladybird, Hoten X, and QR Infra X using the Magic Cube MTC-01 - Walkera WK-2801 Pro Transmitter

http://www.rcgroups.com/forums/showp...3&postcount=62



26. Setup for the Walkera Genius CP, Mini CP, Super CP using the Magic Cube MTC-01 - Walkera WK-2801 Pro Transmitter

http://www.rcgroups.com/forums/showp...1&postcount=66



27. Setup for the Walkera QR X400 - RX2642-D Receiver - Devo Transmitter.

* Beginner Settings
* Standard Settings
* 3D Mode Settings

http://www.rcgroups.com/forums/showp...2&postcount=71



28. Walkera V450D01 – How to setup the TX for the RX2703H-D Receiver – Devo Transmitter.

http://www.rcgroups.com/forums/showp...3&postcount=69


29. Walkera V450D03 – How to setup the TX for the RX2703H-D Receiver – Devo Transmitter.

http://www.rcgroups.com/forums/showp...5&postcount=67


30. Walkera 4F200LM – How to setup the TX for the RX2618-D Receiver

http://www.rcgroups.com/forums/showp...9&postcount=70





"My text, pictures and videos are copyright 2012 -2013 Tom Zadar"






I also have a PDF downloadable setup guides below my pictures.
I will be updating these every time I make any changes in the online setup guides
so make sure you have the most current version before you use the PDF setup guide. I list the version on the download tab and
in the PDF setup guide itself. Download the updated PDF file if you are using it and delete any prior versions of it.
Also with the older versions I posted you could not print out the setup guide. Now you can in the new version as I enabled the option to print in permissions.
There are two setup guides to download.
One is a step by step setup guide of everything on this page.
The other is a step by step setup guide edited and commented by Henk (using my setup guide) for the Dkfuji FBL Head only (or if your made your own Flybarless Head from the stock 4G6 head). He did a nice job on it and he went into much more pitch step by step setup for beginners than I did.



You can do the tilt test after setup to see if the gyros are working and in the
correct direction. For the RX2610V2 you do not need to give throttle or disconnect the motor.
Just tilt the helicopter.
For the RX2610S (like in this video) you need to give throttle to do the tilt test or disconnect the motor and give
throttle then tilt the helicopter.

HeliPal.com - Walkera 4G6S Stabilizer Test (1 min 5 sec)

1. Setup for the Walkera 4G6V Helicopter - RX2610V2 Receiver with 3-Axis Gyro - Walkera WK-2801 Pro Transmitter.



*** First set the RX2610V2 Dip Switches. ***

RX Dip Switch factory positions are both down from the factory.

Set these to the following:

BAL switch down (On) and PIT. REV up (Off).

You can also see my picture below for these settings.



The RX2610V2 is made for the V120D02 which has a longer main shaft
than the 4G6 has so when you put the RX2610V2 on the 4G6
you must compensate for the shorter main shaft with custom pitch
curves that I listed in Step #8 for the 4G6 Flybar head.
Also the RX2610V2 has reverse pitch curves
so on the 4G6 only you must reverse the pitch curves like I did
or reverse the blade grips.


RX2610V2 Weight = 7.1 grams




IMPORTANT!

The PIT and ALIE Servo RX locations will vary between different V120D02 helicopters and different RX2610V's.
Try Option #1 first. If your radio sticks are working correctly you are all set. If not use Option #2.


RX2610V Servo Hookup Option #1


PIT Servo Plug goes into the PIT RX Socket.

ALIE Servo Plug goes into the ALIE RX Socket.

Also see my picture below.



RX2610V Servo Hookup Option #2


PIT Servo Plug goes into the ALIE RX Socket.

ALIE Servo Plug goes into the PIT RX Socket.

Also see my picture below.



*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*



**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.




Step 1. Create a new model (or reset a current model) in the WK-2801 Pro TX.




Step 2. Set to stick mode 2801 if it isn't already set to it. Stay in 2801 stick mode.
*Make sure STICK is set to MODE2* Sometimes it will default to MODE1.

Set the throttle trim all the way down to zero. Default is center.




Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N N N N N N




Step 4. Go into SWASH and set to 1SERVO NORM




Step 5. Go into CURVES THRCURVE and set to:


Norm 0%-25%-50%-75%-100%

ST1 & ST2 - 100%-100%-100%-100%-100%


Another option for ST1 & ST2 if 100% across is too much RPM for your motor is to use these settings.


ST-1 & ST-2 100%-90%-80%-90%-100%


I use this setup. ST-1 is a V Shaped Throttle Curve, ST-2 is 100% across.

ST-1 100%-90%-80%-90%-100%

ST-2 100%-100%-100%-100%-100%




Step 6. Go into CURVES PITCURVE and set to:


1. For the Walkera FBL Head - This is the Stock Walkera Flybarless Head on the V120D02 helicopter.


Norm 36.5%-41%-50%-65%-80%

ST-1 & ST-2 20%-35%-50%-65%-80%

HOLD 20%-35%-50%-65%-80%

With these settings you will have in normal mode -3* to +11* pitch (Depending what the lengths of your servo to swash links are at it could be a little more or less).
In ST-1 & ST-2 mode you will have +/- 11* pitch (Depending what the lengths of your servo to swash links are at it could be a little more or less).



2. For the 4G6 Flybar Head, Dkfuji FBL Head, or if your made your own Flybarless Head from the stock 4G6 head.


Norm 49.5%-45%-37%-21%-5%

ST-1 & ST-2 69%-53%-37%-21%-5%

HOLD 69%-53%-37%-21%-5%

With these settings you will have in normal mode -3* to +13* pitch (Depending what the lengths of your servo to swash links are at it could be a little more or less).
In ST-1 & ST-2 mode you will have +/- 13* pitch (Depending what the lengths of your servo to swash links are at it could be a little more or less).
If this is too much pitch for you (EX: your motor bogs) then you can adjust the pitch curves to whatever you want like Norm -3* to +10*, Stunt Mode +/- 10*, etc.



To change the pitch curve range you want to change the first and last pitch curves
first. So pitch curve L and H. Start with the settings I listed then
for every 4 clicks of the TX button will give you +/- 1* of pitch.
So if you take pitch curve H for ST mode which is 5% (13*) and push the
TX button 4 clicks and increase this to 7% you will then have 12* pitch.
4 more clicks would be 9% (11* pitch), 4 more clicks would be 11% (10* pitch).
Then for the pitch curve L for ST mode which is 69% (13*) push the
TX button 4 clicks and decrease this to 67% (12*). 4 more clicks would be 65% (11* pitch), 4 more clicks would be 63% (10* pitch).
Then set pitch point #1 to be in between pitch curve L and pitch curve #2.
Set pitch point #3 to be in between pitch curve H and pitch curve #2.
Pitch point #2 will always stay 37% which is zero degrees pitch at mid stick.


So for a 12* pitch curve you would want these settings:

Norm 49.5%-45%-37%-22%-7%
-3* to +12* pitch

ST-1 & ST-2 67%-52%-37%-22%-7%
+/- 12* pitch

HOLD 67%-52%-37%-22%-7%




Note:

When doing the mechanical setup of the swashplate turn off the Balance Mode (BAL switch up (Off)) off during setup.
Then when you are finished turn the Balance Mode back on (BAL switch down (On).

Put the throttle at half stick (zero degrees pitch) and adjust the servo to swash links
if needed so that there is no wind from the main blades going up or down from them.
Use the pitch point #2 to adjust and set zero degrees pitch at mid stick.
If you don't have zero degrees pitch at mid stick at 37% and you need to go to a higher percent than 37% to get zero degrees pitch at mid stick
then shorten the swash links. If you need less than 37% to get zero degrees pitch at mid stick then lengthen the swash links. See picture below.

You want the Guide Ball Flybar Pivot to be in the middle of the long head slot at half stick and
you want equal travel from the center to full negative pitch and from the center to full positive pitch.
If you don't have equal travel make adjustments so you do. Also you don't want any binding or bottoming out
at full negative pitch or full positive pitch. See picture below.







Step 7. Go into GYRHLD, GYROSENS and change INH to GYRO/AUX2

Set to 0: 78%
Set to 1: 78%

0: - This is for HH Mode which is 50%-100%
1: - This is for Rate Mode which is 0%-49%

I like to set both for HH Mode. I don't use Rate Mode anyway.




Step 8. Go into GYRHLD, THROHOLD, and change INH to THRO HOLD

ACT
HOLD Pos. -15%




Step 9. Go into TRVADJ and set to:

All 100% except Rudder = L120% R120%




Step 10. Go into DR&EXP:

Set D/R and EXPO to your personal needs/preference.
I use 60% D/R and +35% EXPO. I have the Servo EXT on max on the RX.

Set AUTO to:

ST-1 ACT

ST-2 ACT

HOLD ACT




Step 11.

Bind Radio and RX.




Here are HD settings videos I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.




Walkera 4G6 flybar with the RX2610V2 & WK-2801 Pro TX.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.

Walkera 4G6V FB TX Settings for WK-2801 Pro (2 min 13 sec)

Walkera 4G6 FBL with the RX2610V2 & WK-2801 Pro TX.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.

Walkera 4G6 FBL with RX2610V2 & WK-2801 Pro TX (2 min 25 sec)

* Visit my Blog for my reviews, pictures, and videos of my helicopters *



-

-


6. Setup for the Walkera 4G6S Helicopter - RX2610S Receiver with 3-Axis Gyro - Walkera WK-2801 Pro Transmitter.

6.1 3D Settings

6.2 Beginner Settings

6.3 Setup for the RX2610S and WK-2602 TX



I purchased the Walkera RX2610S: Receiver with 3-Axis Gyro for my 4G6.
I took it out of the package, took off my old RX2609, put the RX2610S on,
put the wires on, went into the radio and programmed it, then powered it up in my
hand and checked to make sure the swashplate was moving correctly to
my stick inputs and that the RX2610S was correcting properly when tilting
the heli. Then I test flew it with the ALIE, ELEV, and Delay pots at the
factory settings. It flew great and the tail holds rock solid. It holds like
my T-Rex 450 V2 does and it will hold throughout the entire battery. I was
surprised to see it hold even with the battery at 3.68 volts!

This is truly a plug and play upgrade.
I have done my heli and Composit's heli and both were a quick and easy upgrade.
I am using firmware version 2.2 on my WK-2801 Pro.
Both the firmware version 2.2 and 2.3 in the WK2801PRO have been tested to work with this 3 axis receiver.
I have seen posts with people using firmware version 2.1 also. So far I see the gyro menu is different than v2.2 & v2.3.

http://www.rcgroups.com/forums/showp...postcount=1520


Differences between the RX-2801, RX-2801E, and RX-2801Pro?

http://www.rcgroups.com/forums/showthread.php?t=1121074


For the RX2610S and WK-2602 TX see these links.

http://www.rcgroups.com/forums/showp...&postcount=969


http://helifreak.com/showpost.php?p=...0&postcount=23



There are 2 different setup guides I made here and one other
setup guide made by nute53.


1. RX2610S Setup Guide - 3D Settings

2. RX2610S Setup Guide - Beginner Settings

3. RX2610S and WK-2602 TX - By nute53


I also have a PDF downloadable setup guide below my pictures.
I will be updating these every time I make any changes in the online setup guides
so make sure you have the most current version before you use the PDF setup guide. I list the version on the download tab and
in the PDF setup guide itself.


RX2610S Weight = 6.89 grams
RX2610S Weight minus cover = 6.16 grams


With these settings you will have in normal mode -10* to +10* pitch.
In ST-1 & ST-2 mode you will have +/- 10* pitch.


You can do the tilt test after setup to see if the gyros are working and in the
correct direction but you will need to give throttle to do this or disconnect the motor and give
throttle then tilt the helicopter.

HeliPal.com - Walkera 4G6S Stabilizer Test (1 min 5 sec)

6.1 RX2610S Setup Guide - 3D Settings


Read this post first:

http://www.rcgroups.com/forums/showp...postcount=1370



This section below is for 3D flying. If you want beginner settings see the Beginners Section.

Switch to the RX2610S from the RX2609. If you already have the RX2610S continue on to setup.

I recommend you pull out one plug at a time from the RX2609 and put it in the RX2610S
and keep repeating until all connectors are installed in the RX2610S. This makes it a
fast switch and you won't connect a plug into the wrong socket this way.

Once the RX2610S is mounted and all the plugs are connected, you are ready to program the radio.

* Make sure on the RX2610S that the BAL switch is down (on) and the PIT. REV switch is up (off).
See my RX2610S Dip Switch Settings picture below.


* Also see pictures below for Step by Step Setup*
You can download this setup guide below with the pictures also in it.


*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*


*These are settings I have tried and use. These are good starting points for you.




Step 1. Create a new model in the WK-2801 Pro TX



Step 2. Set to stick mode 2601 if it isn't already set to it. Stay in 2601 stick mode.



Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N R N R N N




Step 4. Go into SWASH and set to 3SERVOS 120*




Step 5. Go into SWATTS, SWASHMIX and set to: (Do not set any to -60%).


ELEV 60%
AILE 60%
PIT 60%




Step 6. Go into GYRPAT and set to:

PLT -124 ATS 0%
Pit +500 SEN 23%
Exp1 0
Exp2 0




Step 7. Bind Radio and RX. Make sure the throttle trim is all the way down. The default is center.



For 3D flight put the throttle at half stick (zero degrees pitch) and adjust the swash links if needed so that there is no wind from the main blades
going up or down from them.


If you want D/R & Expo -


Assign a Hot Key:

If you want Expo and D/R set COMPTB to 2801 and assign a hot key for Expo & D/R. Then set
COMPTB back to 2601.
To do this go into 2801 mode and go into the Expo, D/R screen. Then push down
at the same time the UP and DN buttons. A menu will pop up called
Hot Keys. Select the button you want to assign it to then hit ENT.
Now go back to mode 2601 and the hot key (s) you set will
be there.
This trick will work for almost all menus like throttle, pitch, gyro gain,
subtrim, etc...


To recall a Hot Key you assigned:

You MUST HOLD DOWN the left EXT button and "keep it down" then
press the hot key button you assigned that you
want. Then your menu will pop up for you.


Make sure that the heli is perfectly balanced because any vibrations and the gyros will make the swashplate move around.

Use D/R and or Expo to tame the heli down and adjust the RX pots to what you like.
Turn RUDD EXT pot up to get full slider travel.


Important!

When doing the mechanical setup of the swashplate turn off the Balance Mode (BAL switch up (Off)) off during setup.
Then when you are finished turn the Balance Mode back on(BAL switch down (On).

Secure the RX with rubber bands tight or the RX will shake the heli as it is not secure enough with just the RX tape.
I found this out with both the helicopters I setup. It shook hard until I put finger pressure on the RX then it smoothed out perfect!
So I then added rubber bands and it works great.

Make sure that the heli is perfectly balanced because any vibrations and the gyros will make the swashplate move around.



From what have experienced it's best to set the ALIE gyro, ELEV gyro,
and delay pot at 50% (12 o clock position) then fine tune them to your
personal preference/flying style. So if you want the most
correction crank the ALIE, ELEV pots up as high as possible
without getting swash rocking. Then adjust the delay pot.

For most people the 11 -12 o clock position for ALIE and ELEV
and 9 -12 o clock position for the delay pot seems to work well.



Here is a HD settings video I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.


Walkera 4G6S TX 3D Settings with the WK-2801 TX

Walkera 4G6S TX 3D Settings for WK-2801 Pro TX (1 min 0 sec)

--------------------------------------------------------------------



Beginners Section: Settings, information, and setup.


These are what wowhobbies and Walkera set the radio settings to.


6.2 RX2610S Setup Guide - Beginner Settings


* Make sure on the RX2610S that the BAL switch is down (on) and the PIT. REV switch is up (off).
See my RX2610S Dip Switch Settings picture below.


*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*

**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.



Step 1. Create a new model in the WK-2801 Pro TX



Step 2. Set to stick mode 2601 if it isn't already set to it. Stay in 2601 stick mode.



Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N R N R N N




Step 4. Go into SWASH and set to 3SERVOS 120*




Step 5. Go into SWATTS, SWASHMIX and set to: (Do not set any to -60%).


ELEV 60%
AILE 60%
PIT 60%




Step 6. Go into GYRPAT and set to:

PLT 0 ATS 0%
Pit 0 SEN 23%
Exp1 0
Exp2 0




Step 7. Bind Radio and RX. Make sure the throttle trim is all the way down. The default is center.



If you want D/R & Expo -


Assign a Hot Key:

If you want Expo and D/R set COMPTB to 2801 and assign a hot key for Expo & D/R. Then set
COMPTB back to 2601.
To do this go into 2801 mode and go into the Expo, D/R screen. Then push down
at the same time the UP and DN buttons. A menu will pop up called
Hot Keys. Select the button you want to assign it to then hit ENT.
Now go back to mode 2601 and the hot key (s) you set will
be there.
This trick will work for almost all menus like throttle, pitch, gyro gain,
subtrim, etc...


To recall a Hot Key you assigned:

You MUST HOLD DOWN the left EXT button and "keep it down" then
press the hot key button you assigned that you
want. Then your menu will pop up for you.


Make sure that the heli is perfectly balanced because any vibrations and the gyros will make the swashplate move around.

Use D/R and or Expo to tame the heli down and adjust the RX pots to what you like.
Turn RUDD EXT pot up to get full slider travel.

Important!

When doing the mechanical setup of the swashplate turn off the Balance Mode (BAL switch up (Off)) off during setup.
Then when you are finished turn the Balance Mode back on(BAL switch down (On).

Secure the RX with rubber bands tight or the RX will shake the heli as it is not secure enough with just the RX tape.
I found this out with both the helicopters I setup. It shook hard until I put finger pressure on the RX then it smoothed out perfect!
So I then added rubber bands and it works great.

Make sure that the heli is perfectly balanced because any vibrations and the gyros will make the swashplate move around.


From what have experienced it's best to set the ALIE gyro, ELEV gyro,
and delay pot at 50% (12 o clock position) then fine tune them to your
personal preference/flying style. So if you want the most
correction crank the ALIE, ELEV pots up as high as possible
without getting swash rocking. Then adjust the delay pot.

For most people the 11 -12 o clock position for ALIE and ELEV
and 9 -12 o clock position for the delay pot seems to work well.



Here is a HD settings video I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.


Walkera 4G6S TX Beginner Settings with the WK-2801 TX

Walkera 4G6S TX Beginner Settings for WK-2801 Pro TX (1 min 4 sec)

See DLee2010's links below. These will help tame the heli down
and improve landing pitch.

Use D/R and or Expo also to tame the heli down.




1. Thanks Hjns!

Absolute Beginners Walkera 4G6/4G6S thread

http://www.rcgroups.com/forums/showthread.php?t=1243755



2. Thanks DLee2010!

I have tried this and it tames the heli response down
as it reduces the pitch. Combine this with D/R and or EXPO and you
will have a tame heli to start on.
Note: You don't want to flip up into Idle up or your going to have a
big pitch jump. Only use this to learn on in normal mode. Once you can
fly well set everything back to what I have listed in my setup guide
and you will be ready for regular or 3D flight.


http://www.rcgroups.com/forums/showp...postcount=1355


http://www.rcgroups.com/forums/showp...postcount=1354


http://www.rcgroups.com/forums/showp...postcount=1381


http://www.rcgroups.com/forums/showp...postcount=1402


http://www.rcgroups.com/forums/showp...postcount=1409


http://www.rcgroups.com/forums/showp...postcount=1415


http://www.rcgroups.com/forums/showp...postcount=1416


-------------------------------------------------------------------------------------------



Note:


You can't adjust the throttle curve in normal mode or ST1 mode.
Throttle curves are hard coded. There appears to be no way to adjust the throttle curve with this Rx.
So you adjust throttle curves to adjust the pitch curves.


The plain fact is the throttle curves are hard coded into the 2610S Rx. There appears to be no way to adjust the throttle curve with this Rx.

PLT is to set your top and bottom pitch in Idle-up. PIT is to set your hover pitch in Nor flight mode.

Adjusting throttle curve in 2801 NOR affects pitch curve in 2601 NOR.
Adjusting throttle curve in 2801 St1 affects pitch curve in 2601 Idle-up (3D).


PLT controls the amount of +/- pitch you have in Idle-up while PIT adjusts how much pitch you have in Nor flight.
The lower (more "-") you add to PLT, the less max pitch you will have. You can also then adjust the Idle-up pitch curve
itself (if you have a 2801Pro) by switching to 2801 mode and adjusting the throttle curve and going back to 2601 stick mode.
Manny and I use this option to smooth out the curve so it "feels" right in flight. The higher you make PIT value (more "+") the
less pitch you have at start-up and Nor flight. So in order to have "0" pitch at mid-stick, the values are roughly what you have.
If you keep PLT at "0", the pitch curve is too steep and you end up with way too much pitch (at top and bottom collective stick) that
will bog the motor in Idle-up flight mode. If you leave the PIT at "0", you will have too much pitch at 1/4 to 1/2 stick in NOR flight
mode which makes it harder to control and land without cutting the motor out.


Throttle Hold does not work in ST-1 or ST-2, only in Norm mode. The flight mode is to go into 3D mode and gives constant
throttle with pitch control (collective).

Here are the settings I am using.

Under GyrPat I have
PLT -124 ATS 0%
Pit +500 SEN 23%
Exp1 0
Exp2 0

The throttle curve is very aggressive in stunt modes as soon as you leave center stick pitch comes in really quick so I went under Stick put it in 2801 mode
then went under Throttle curve and this is what I have my ST-1 set to.

ST-1 0 38 50 62 100
This will change your pitch curve in ST-1 in 2601 mode to make it less aggressive.

Now on the on the RX if you look at it down from the front of the heli it is set up like this.

Bal Delay is set to 8:30
Elev gyro 11:30
Aile gyro 12:30
Elev/Aile EXT is maxed out.

Also make sure that the heli is perfectly balanced because any vibrations and the gyros will make the swashplate move around.



* Visit my Blog for my reviews, pictures, and videos of my helicopters *




6.3 Setup for the RX2610S and WK-2602 TX

This setup is for the RX2610S and WK-2602 TX. Special tanks to nute53
for letting me post this in my setup guide.

I installed a 2610S Rx in my almost new Novus 125 CP ,and have finally got it dailed- in for indoor practice -been way too windy past couple weeks to attempt outside testing.

The Rx Pots were set at :

Balance Delay - approx. 65%

Elev. & Ail Gyro- approx. 50%

Elev. & Ail Extent- approx. 35% (I have this set low on Rx & dual rate on Tx set high to get full rudder throw, yet toned down cyclic)

Rudd Extent- approx. 85%


Transmitter settings were set at:

Elev.,Ail.,Throttle,& Gear all set to norm.

Pit. & Rudder set to rev.

Aux off, Buzz on

Expo-off, Plt-Pit-off, Rudd.Mix-norm, Gyro-on

Since this is a re-branded 2602 Tx, it is set to 6ch. mode to bind, and I have the V1 & V2 knobs set to approx. 60%. Still not sure how the V1 & V2 translate to pitch & throttle curve setup with this Rx, but this seems to be the best compromise so far, without bogging down the stock motor.
This seems to be the most stable settings for just indoor hovering. If anyone has any suggestions, or could help translate the 2801 Tx pitch-throttle curves to a Helimax 6024 (2602 Tx),that would be very helpful. I understand the 2801 must bind in 2601 mode, and all the functions are not available with this first generation 2610S Rx as relates to setting up the 2801 Tx-including throttle can't be set to 100% in norm mode,curves must be set in 2801 mode-then switched to 2601 to bind.
I am getting a slight bobbing action (front & back) with this Rx, not sure if it is a gyro or balance delay setting-have tried various pot settings with limited success-more balance or gyro = more pronounced bobbing. I have also read that any excess vibration may cause irregular gyro motion, but seems to be running very smoothly, so not sure.
Overall very pleased with the extra stability the 2610S Rx offers, and after some more practice with this setup,will be installing a flybarless head that I already have ready to go, and see how that works with the new Rx.

-

-


5. Setup for the Walkera 4G6 Helicopter - RX2609 Receiver - Walkera WK-2801 Pro Transmitter.


I also a have PDF downloadable setup guide at the bottom of this post.


**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.


Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.


Settings for Normal and 3D flight


Set to stick mode 2801


REVERS - 1R, 2N, 3N, 4R, 5N, 6R, 7N, 8N


SWASH - 3SERVOS 120*


SWATTS, SWASHMIX -

ELEV 60%

AILE 60%

PIT -60%


GYRHLD - Gyrosens

0: 80%
1: 80%



THRCURVE -

Norm 0%-25%-50%-75%-100%

ST-1 100%, 90%, 80%, 90%, 100%

ST-2 100%, 100%, 100%, 100%, 100%



PITCURVE -

Norm 31%, 42%, 50%, 75%, 100%

ST-1 0%-25%-50%-75%-100%

ST-2 0%-25%-50%-75%-100%



DR&EXP -

ELEV - D/R 80% Expo +30%

ALIE - D/R 80% Expo +30%


AUTO -

ST-1 ACT

ST-2 ACT

HOLD ACT



Here is a HD settings video I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.



Walkera 4G6 TX Settings with the WK-2801 Pro TX

Walkera 4G6 FB TX Settings for WK-2801 Pro TX (2 min 14 sec)

----------------------------



WK-2801/pro radio settings used on the Manual Campos 3D video:


Set to stick mode 2801


REVERS - 1R, 2N, 3N, 4R, 5N, 6R, 7N, 8N


TRVADJ - 100% on all except rudder at 120%


SWASH - 3SERVOS 120*


SWAATS - Swashmix - Elev 79% Aile 79% Pit. -58%


GYRHLD - Gyrosens - Gyro/Aux2 0:81% 1:80%


Throhold - Thro Hold - Hold Pos - -10%


DR&EXP - Elev - D/R 100% Exp +30%


Aile - D/R 100% Exp +30%


Rudd - D/R 67% Exp +15%


Set AUTO to:

ST-1 ACT

ST-2 ACT

HOLD ACT



CURVES - Thrcurve - Norm - 0-35-100-100-100


ST-1 - 100-flat across


ST-2 - 100 flat across


Pitcurve - Norm - 31.5-41.5-50-75-100


ST-1 - 0-25-50-75-100


ST-2 - 0-23-50-77-100



* Visit my Blog for my reviews, pictures, and videos of my helicopters *

-

-

2. Setup for the Walkera V100D01 - RX2441V Receiver - Walkera WK-2801 Pro Transmitter.


I also have a PDF downloadable setup guide under my pictures.
I will be updating these every time I make any changes in the online setup guides
so make sure you have the most current version before you use the PDF setup guide. I list the version on the download tab and
in the PDF setup guide itself.


*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*




Step 1. Select a new model (or reset a model)


Step 2. COMPTB 2401 and STICK to MODE2


3. REVERS - 1R, 2R, 3N, 4N

Channel 1 is ELEV and channel 2 is ALIE.


Make sure the throttle trim is set all the way down. Default is center.



D/R and Expo -

If you want Expo and D/R set COMPTB to 2801 and assign a hot key for Expo & D/R. Then set
COMPTB back to 2401.
To do this go into 2801 mode and go into the Expo, D/R screen. Then push down
at the same time the UP and DN buttons. A menu will pop up called
Hot Keys. Select the button you want to assign it to then hit ENT.
Now go back to mode 2601 or 2401 and the hot key (s) you set will be there.
This trick will work for almost all menus like throttle, pitch, gyro gain,
subtrim, etc...
To bring up your hot key you need to hold down the left EXT button and keep it down then
press the hot key button you assigned that you want.
That's it, you can now fly the V100D01.

You need to know this. When you plug in the battery you will get 2 quick beeps, then turn on the TX and wait for it to bind.
Now wait for 3 beeps from the tail motor and in a 2-3 seconds and you will get 3 beeps from the main motor also.
Now you are ready to fly.


Here is a HD settings video I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.

Walkera V100D01 TX Settings for WK-2801 Pro TX (0 min 37 sec)

* Visit my Blog for my reviews, pictures, and videos of my helicopters *


-

-


1. Setup for the Walkera 4#3B & CB100 Helicopter - RX2406C, RX2605A Receiver - Walkera WK-2801 Pro Transmitter.


I also have a PDF downloadable setup guide at the bottom of this post.


*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*




Setup for the 4#3B & CB100 with WK-2801 Pro and RX2406C.


Stick - Mode2, COMPT 2401


REVERS - 1R, 2N, 3N, 4N,



Your throttle trim MUST be all the way down or the tail motor esc will not arm.


If you want D/R & Expo -


Assign a Hot Key:

If you want Expo and D/R set COMPTB to 2801 and assign a hot key for Expo & D/R. Then set
COMPTB back to 2401.
To do this go into 2801 mode and go into the Expo, D/R screen. Then push down
at the same time the UP and DN buttons. A menu will pop up called
Hot Keys. Select the button you want to assign it to then hit ENT.
Now go back to mode 2401 and the hot key (s) you set will
be there.
This trick will work for almost all menus like throttle, pitch, gyro gain,
subtrim, etc...


To recall a Hot Key you assigned:

You MUST HOLD DOWN the left EXT button and "keep it down" then
press the hot key button you assigned that you
want. Then your menu will pop up for you.



See this video also:

How to use the advanced setting options of the Walkera 2801Pro TX for use on
the 4#3B with the 2406 RX Range (2406, 2406A, 2406B, 2406C).

4#3B with 2801Pro: Throttle Curve, Dual Rate and Expo (2 min 26 sec)

----------------------------------------------



Setup for the 4#3B & CB100 with WK-2801 Pro and RX2605A.


Swash - 1servo


Thrcurv - Norm - Linear (default) 0%-25%-50%-75%-100%


PITCURV - Linear (default) 0%-25%-50%-75%-100%


Gyrhld: Gryo - 85% - Try this to start out with. It will be INH at default. Switch it to GYRO/AUX2


REVERS - All are normal with the RX2605A in 2801 stick mode.


STICK - MODE2, COMPT 2801


Your throttle trim MUST be all the way down or the tail motor esc will not arm.


On the THRCURV menu you want 0-25-50-75-100.
You will also see IN and OUT below the percent.
Make sure OUT is set at -16. This is your throttle trim adjustment
on the radio. So if the trim is all the way down it will read -16
or maybe -15.



Reciever:

AILE to left/right servo

ELEV to up/down servo

PIT not used

RUDD not used

TAIL MOT SIG to tail ESC

MAIN MOT SIG not used

You MUST put the MIX pot on the 4in1 to MAX.
Then if needed go into the subtrim in your RX - SUBTRIM RUDD and turn it up to
where you need it until the tail holds straight. I have mine at R 21.

The power cable on the 4in1 that goes to the battery is not used in this setup.
I took mine off to save weight and clutter.



* Visit my Blog for my reviews, pictures, and videos of my helicopters *



-

uff
Good job
congratulation!

Very well done Tom.

Beyond impressive.

Your attention to detail is admirable. Hope you are suitably rewarded if you follow suit in whatever you do for a living.

Amp

Nice work Tom. You have done way more than I would be willing to do with this one. Awesome job bud.

Darryl

Great job Tom, I don't know what RCGroups would do without your hard work and I love for the Hobby. Thankyou for great review everything else you for US Vronny

Hi Tom,

I installed RX2610V2 that had reached from WOW yesterday in 4G6FBLmod.
Then, I found very important trick to the setting of 1SERVO of TX(WK2801Pro V2.2).

It is that a top and bottom of SWASHPLATE direction changes by the polarity of (+/-) of PIT of SWASHMIX of 3SERVOS.
Numerical values are quite unrelated and only the polarity of PIT influences the direction.

It sets to 3SERVOS, the polarity of (+/-) of PIT of SWASHMIX is set, and it returns it to 1SERVO again once.

In (+) setting of SWASHMIX PIT, SWASH is moved in the direction of down by throttle UP.
It is moved in the opposite direction in (-) setting.

Do not forget to return it to the setting of 1SERVO.

Thanks,

-

18. Setup for the Eflight Blade mCPX V1 with Futaba 9CHPS with an 8 channel Spectrum module. Blade mCPX V1 Helicopter.

8.1 Setup for the Eflight Blade mCPX V1 Helicopter - Futaba 10CHP settings with Spektrum module

8.2 Setup for the Eflight Blade mCPX V1 - JR 11x ZERO settings for MCPX

*JR 9303 transmitter settings. Use the DX7 or DX8 transmitter settings.





Special thanks to loopy1 for letting me post his settings.



SWH1
D/R Expo- 100%
Endpoints- 100 (all)
Sub trim- 0 (all)
REVERSE-
1. AIL- REV
2. ELE- REV
3. THR- REV
4. RUD- REV
5. GYR- NOR
6. PIT- REV
7. AV1- NOR
8. AV2- NOR

Trim- default
Thr- Cut- INH
Aux-CH- Defaults
Parameter- Heli (SWH1)
MODUL- PPM
ATL- ON
TH-CURVE NOR- 1-0%, 2-70.5%, 3- 80%, 4- 84.5%, 5- 90.5%
Idle up 1- 99.5%, 2- 97%, 3- 95%, 4- 97%, 5- 99.5
Idle up 2 and 3 are the same as IU 1
HOLD- 0,0,0,0,0
REVO- INH
Timers- 6:00
PITCH CURVE NOR- 44%, 47.5%, 50%, 75%, 100%
Idle up 1- 17.5%, 34%, 50%, 66%, 82.5%
Idle up 2- 15%, 33.5%, 50%, 66.5%, 85%
Idle up 3- 12.5%, 31%, 50%, 69%, 87.5%
HOLD- 15%, 32%, 50%, 68%, 85%
Revo Mix- INH
Gyro Sens-
Mode- GY
AVC- 75%
NOR- 75%
Switch- B

HOVER- Throttle, pitch and HI/LO Pitch--- all 3 are INH
THR-HOLD- Mix- On/Off
Pos- 0%
Switch- G
OFFSET- INH
DELAY- all 0%
GOVERNOR, THRO-NEEDLE, Swash->Throttle- All 3 are INH
Switch select- As you prefer your switches
MIX 1,2 and PMX-6 CRV- are all INH




8.1 Setup for the Eflight Blade mCPX V1 with 8.1 Futaba 10CHP settings with Spektrum module. Blade mCPX V1 Helicopter.

This setup guide was made by: Turboparker

http://helifreak.com/showthread.php?t=287109


8.2 Setup for the Eflight Blade mCPX V1 - JR 11x ZERO settings for MCPX V1.

This setup guide was made by: rchelijc

http://www.rcgroups.com/forums/showp...&postcount=106



-

-

3. Setup for the Walkera V100D03 Helicopter - RX2620V Receiver with 3-Axis Gyro - Walkera WK-2801 Pro Transmitter.

6.1 Justin Proud settings (ClubHeli's test pilot)

I also have a PDF downloadable setup guide at the bottom of this post.


These are the factory programmed settings.

Special thanks to vronny for taking the time to send me all the settings.





*** RX2620V Dip Switches and Gyro Pots ***


I have added a picture of the RX below.


[PITCH REV - Off ]

[WK-ADJ - ON ]



Gyro Pot Settings:


[ELE/AILE EXT 12 o'clock ]

[ELE.G.S. knob 12 o' clock ]

[AILE.G.S knob set 12 o' clock ]



*Make sure you verify the settings after you are done before you fly the helicopter.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.*




Step 1. Create a new model (or reset a current model) in the WK-2801 Pro TX.




Step 2. Set to stick mode 2801 if it isn't already set to it. *stick mode2 -comptB 2801 -IDCODE-random*

Stay in 2801 stick mode.

*Make sure STICK is set to MODE2* Sometimes it will default to MODE1.


Set the throttle trim all the way down to zero. Default is center.




Step 3. Go into REVERS and set to:

1 2 3 4 5 6 7 8
N N N N N N N N




Step 4. Go into SWASH and set to 1SERVO NORM




Step 5. Go into CURVES THRCURVE and set to:


Norm L:= 0% 1:= 38.5% 2:= 69.5% 3:= 86.5% H:= 100%


ST1 & ST2 L:=100% 1:=80% 2:=70% 3:=80% H:=100 (V Shaped Throttle Curve)




Step 6. Go into CURVES PITCURVE and set to:



Norm L:=51.5% 1:=53.5% 2:=58.5% 3:=75% H:=85%

ST-1 & ST-2 L:=28% 1:=41% 2:=50% 3:=63% H:=74%

HOLD L:=7.5% 1:=27% 2:=50% 3:=75% H:=100%




Step 7. Go into GYRHLD, GYROSENS and change INH to GYRO/AUX2

0:=70%

1:=20%

0: - This is for HH Mode which is 50%-100%
1: - This is for Rate Mode which is 0%-49%



Step 8. Go into GYRHLD, THROHOLD, and change INH to THRO HOLD

ACT
HOLD Pos. -15%



Step 9. Go into TRVADJ and set to:

All 100%



Step 10. Go into DR&EXP:



DR/EXPO

ELEV - Pos-0 D/R 80% Expo LIN

AILE - Pos-0 D/R 80% Expo LIN

RUDD Pos-0 D/R 100% EXPO LIN


Set AUTO to:

ST-1 ACT

ST-2 ACT

HOLD INH




Other Settings:


[PROGMIX all OFF ]


[FAILSAF all INH ]


[STEP all 5]


[INPUT- GEAR:GEAR, AUX2: AUX2/GYRO , AUX3: F.MOD]


[SUBTRIM all 0]




Step 11.

Bind Radio and RX.




Here is a HD settings video I made. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.
Note: Set to STICK MODE 2 not MODE 1. It defaulted to Mode 1 as I loaded the model.

Walkera 2801 Pro TX Factory Settings for V100D03 (2 min 44 sec)

*************************************



6.1 Justin Proud settings (ClubHeli's test pilot).


Thanks Justin for letting me post these.



-----------------------------------------------



I'm adding my radio settings for the 2801 pro for the V100D03BL.


CHNL Reversing are all in the NORM pos.


My gyro gain for the tail is at about 70% and may very from one heli to another.


THROTTLE CURVE


NORM ST-1&2
L 0% L 100%
1 25% 1 100%
2 50% 2 100%
3 75% 3 100%
H 100% H 100%


PITCH CURVE(this may also very from heli too heli but great starting point)


NORM ST1&2
L 43.5% L 27%
1 46 % 1 35%
2 50% 2 50%
3 67% 3 67%
H 77% H 77%


The gyro pots on the RX are set too just less than 50% and the servo EXT. is turned up to about 75%. These settings are a pretty good starting point.
I fly with no expo but you may want too add some if you feel needed. This thing flies great for me with these settings.



-------------------------------------------------------------------------



Here is a HD video I made (Tom Z) using Justin's settings. If you want to view it in HD double click it and it will open up on YouTube. Then selct HD.
Follow my full setup above and then use these Throttle and Pitch Curves which are Justin's settings instead of the ones I listed above.

Walkera 2801 Pro TX Custom Settings for V100D03 (1 min 1 sec)

Justin's Videos:

V100D03BL 3D Flight (5 min 1 sec)

V100D03BL flips (3 min 44 sec)

-

-

18. Setup for the Eflight Blade mCPX V1 Helicopter - Spektrum DX6I, DX7, and DX8 transmitter.

JR 9303 transmitter settings. Use the DX7 or DX8 transmitter settings.


* Standard Settings

7.1 Buildem336 (Manuel) 3D settings for the Spektrum DX7

7.2 Beginner Settings

7.3 Transmitter and Receiver Binding




Set your swash to zero degrees pitch at mid stick. See this video.

Mcpx 0 pitch setup (4 min 42 sec)

Standard Settings




Spektrum DX6I:


Model Type: HELI

Reverse: Set Pitch to reverse. All the rest are normal.

Swash Type: 1 Servo 90

Travel Adjustment: Pitch = 75% for H and L

Throttle Curve

NORM 0% 40% 60% 80% 100%
STUNT 100% 100% 100% 100% 100%
HOLD 0% 0% 0% 0% 0%

Pitch Curve

NORM 30% 40% 50% 75% 100% *
STUNT 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100 **

* If you are a beginner you can use NORM 50% 50% 50% 75% 100%. This will give you zero degree negative pitch for indoor flying or outdoor flying with no wind.
The heli will not slam to the ground if you pull the throttle down to fast due to having negative pitch. Do not use this for stunt modes, only use this for normal mode.

** Option 2. HOLD 50% 50% 50% 50% 50%
This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
This will also prevent a boom strike.
The swash does not move with TH with these settings.
If you want control of the swash in TH to help you land in a crash don't use these settings.



DR&EXP

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.

ELEV D/R = 70% EXP +30%

AILE D/R = 70%, EXP +30%



Here is a settings video in HD I made.

Spektrum DX6I Factory Settings for Blade mCPX (2 min 26 sec)

Spektrum DX7

Model Type: HELI

Reverse: All are normal.

Swash Type: 1 Servo 90

Travel Adjustment: Pitch = 75% for H and L

Throttle Curve

NORM 0% 40% 60% 80% 100%
ST-1 100% INH 80% INH% 100%
ST-2 100% 100% 100% 100% 100%
HOLD 0% 0% 0% 0% 0%

Pitch Curve

NORM 30% INH 50% INH 100% *
STUNT 0% INH 50% INH 100%
HOLD 0% INH 50% INH 100% **

* If you are a beginner you can use NORM 50% 50% 50% 75% 100%. This will give you zero degree negative pitch for indoor flying or outdoor flying with no wind.
The heli will not slam to the ground if you pull the throttle down to fast due to having negative pitch. Do not use this for stunt modes, only use this for normal mode.

** Option 2. HOLD 50% 50% 50% 50% 50%
This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
This will also prevent a boom strike.
The swash does not move with TH with these settings.
If you want control of the swash in TH to help you land in a crash don't use these settings.



DR&EXP

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.

ELEV D/R = 70% EXP +30%

AILE D/R = 70%, EXP +30%



Here is a settings video in HD I made.

Spektrum DX7 Factory Settings for Blade mCPX (3 min 34 sec)

Spektrum DX8

Model Type: HELI

Reverse: All normal

Swash Type: 1 Servo Normal

Travel Adjustment: Pitch = 75% for H and L

F-Mode Setup
Flight Mode: F Mode
Hold: Hold

Throttle Curve

NORM 0% 40% 60% 80% 100%
ST-1 100% 90% 80% 90% 100%
ST-2 100% 100% 100% 100% 100%
HOLD 0% 0% 0% 0% 0%

Pitch Curve

NOR 30% 40% 50% 75% 100% *
ST-1 0% 25% 50% 75% 100%
ST-2 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100% **

* If you are a beginner you can use NORM 50% 50% 50% 75% 100%. This will give you zero degree negative pitch for indoor flying or outdoor flying with no wind.
The heli will not slam to the ground if you pull the throttle down to fast due to having negative pitch. Do not use this for stunt modes, only use this for normal mode.

** Option 2. HOLD 50% 50% 50% 50% 50%
This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
This will also prevent a boom strike.
The swash does not move with TH with these settings.
If you want control of the swash in TH to help you land in a crash don't use these settings.



DR&EXP

Set D/R and EXPO to your personal needs/preference. These should be good for beginners.
You can set more or less than 70% D/R if you want and more or less than +30% EXPO if you want.

ELEV D/R = 70% EXP +30%

AILE D/R = 70%, EXP +30%



------------------------------



7.1 Buildem336 (Manuel) 3D settings for the Spektrum DX7.



D/R % Expo
Rudd
EXP -5%
D/R 125%

AILE
EXP +10%
D/R 100%

ELEV
EXP +10%
D/R 100%

Travel Adjust
Rudd
L150%
R150%

Pit
L88%
R88%

Throttle curve
Normal don't use
ST-1 ST-2
100% across

Pitch ST-1 ST-2
0 25 50 75 100


My set up for indoor 3d is 101 D/R on elev, aile, and +18 expo its stable around center and flips pretty fast.


Manuel

Brushless Mcp X 3d flight (2 min 28 sec)

Blade mCP X indoor 3d flight (1 min 41 sec)

7.2 Beginner Settings

These are from others and not from me.
Try different ones to see which ones work best for you.




Mcpx as a more beginner friendly FP heli

Mcpx as a more beginner friendly FP heli (9 min 28 sec)

Taming the mCP


Set your pitch curve so that zero pitch is when the stick is all the way down (50-INH-75-INH-100), not half way like the manual suggests; this will make the collective less sensitive and slightly reduces the head speed. You'll need to reset this to the values in the manual and get used to hovering at 75% throttle before you think about aerobatics, but it's OK to 'cheat' a little to begin with.
Set your low rates to 50% instead of the 70% recommended. Leave the expo at 30%. Don't even think about using high rates!





See these posts for more tame settings:


http://www.helifreak.com/showthread.php?t=407020


http://helifreak.com/showpost.php?p=3722808&postcount=9


http://helifreak.com/showpost.php?p=3653105&postcount=2


http://www.helifreak.com/showpost.ph...71&postcount=1



-

-

8. Setup for the Walkera Genius CP Helicopter - RX2625H Receiver: WK2801 compatible - Walkera WK-2801 Pro Transmitter.

* 3D Settings
* buildem336 3D Settings


**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.

The settings listed below are for 3 axis mode.



3D Settings


See picture below for the RX factory pot settings.

Make sure you verify the settings after you are done before you fly the Genius CP.
On the WK-2801 Pro you must hit ENT to save a setting, if you just back out of the menu it will not save the setting.




Step 1. Create a new model (or reset a current model) in the WK-2801 Pro TX.



Step 2. Set to stick mode 2801 if it isn't already set to it. Stay in 2801 stick mode.
*Make sure STICK is set to MODE2* Sometimes it will default to MODE1.



Step 3. Go into REVERS and set to: ALL NOR




Step 4. Go into SWASH and set to: 1 SERVO NORM




Step 5. Go into CURVES THRCURVE and set to:

Normal - 0-25-100-100-100

ST-1 - 100-100-100-100-100

ST-2 - 100-100-100-100-100




Step 6. Go into CURVES PITCURVE and set to:

Normal - 32-41-50-75-100

ST-1 - 0-25-50-75-100

ST-2 - 0-25-50-75-100

HOLD - 50-50-50-50-50 > This will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch. The swash does not move with TH with these settings. This will also prevent a boom strike.
There is no autorotation for the Genius CP helicopter. If you want control of the swash in TH to help you land in a crash then don't use these settings. Use the settings below.

*HOLD - 0- 25-50-75-100 > If you are setting up pitch curves use these settings first then switch to the settings above to fly.



Step 7. Go into GYRHLD, GYROSENS and change INH to GYRO/AUX2

Set to: GYRO/AUX2
0: 82%
1: 82%


Step 8. Go into GYRHLD, THROHOLD, and change INH to THRO HOLD

Set to: THRO HOLD ACT
HOLD Pos. 0%

Set throttle trim to center!

It looks like Genius has firmware to run like this.

Read this post:

http://www.rcgroups.com/forums/showthread.php?t=1510032




Step 9. Go into TRVADJ and set to:

ELEV - D & U:120%, AILE - L & R: 120%, Pitch travel 70%, 100% ON THE REST


Step 10. Go into DR&EXP:

Set to: ELEV D/R - 106%, EXP +25%
AILE D/R - 106%, EXP +25%
RUDD D/R - 100%, EXP -2%
AUTO - Set all to ACT if you want these D/R & EXPO settings to work in Normal, ST-1, and ST-2 modes automatically for you.


Step 11. SWAATS - Swashmix


Set to: NOT ACTIVE IN 1 SERVO SWASH TYPE



Step 12.

Bind Radio and RX.

Check and verify swash is moving correct with cyclic input and 3 axis gyro is compensating correct.



-------------------------------------------------------------------------------------------------------


buildem336 3D Settings



These are the 3D settings that buildem336 uses for his Genius CP and WK-2801 Pro TX.
Use Blade mCPX V3 tail rotor or the tail will blow out using the stock tail blade.




Settings for Stock heli are.

Travel adjust.
Elev D150% U150%
Aile L150% R150%
Thro H100% L100%
Rudd L93% R140%
Gear -100% -100%
Pit H87% L87%

Dr&EXP
Rudd
D/R 125%
EXP -80%

ELEV
D/R 125%
EXP +50

AILE
D/R 125%
EXP +50

Thrcurv
ST-1- ST-2
100% across

Pitch curves
0 25 50 75 100

Gyro
83%

On the Rx adjustment all are facing forward toward the front of the heli.

Settings for brushless heli for outside flying. I don't have any indoor settings yet for brushless.

Travel adjust.
Elev D115% U115%
Aile L115% R115%
Thro H100% L100%
Rudd L93% R140%
Gear -100% -100%
Pit H73% L73%

Dr&EXP
Rudd
D/R 125%
EXP -80%

ELEV
D/R 125%
EXP +25

AILE
D/R 125%
EXP +25

Thrcurv
ST-1- ST-2
100% across

Pitch curves
0 25 50 75 100

Gyro
85%

The adjustment on the Rx the first closest to the main shaft is facing forward to the front of the heli and the other two are in stock location.

Walkera Genius Cp indoor 3d flight (2 min 15 sec)

Walkera Genius Cp brushless 3d flight (2 min 35 sec)

-

-

8. Setup for the Walkera Genius CP Helicopter - RX2625H Receiver: Devo compatible - Devo 7 Transmitter.
These settings should also work for the Devo 6, Devo 8, Devo 10, and Devo 12 transmitters.

* Intermediate to Advanced Settings



**These are settings I have tried and use. These are good starting points for you.
Some people use these settings as they are and others change them to meet there needs.

The settings listed below are for 3 axis mode.


This setup will give you 8-9* +/- pitch.
If you want more or less pitch turn up or down the pitch travel.
DO NOT set Rudder travel adjustment more than 100%. The tail will blow out
hard with any setting over 100%.

These are the settings I am using.
With these settings there is no change at all in RPM or pitch switching between modes. Normal, ST-1, and ST-2.
The heli won't rise or drop switching between modes.

Copy a model in the Devo 7:
At the default screen Press ENT, select MODEL on the top - Press ENT, select COPY - Press ENT, for SOURCE select select GENIS - Press ENT, for DEST select MOD 2 - Press ENT.




Intermediate to Advanced Settings


See picture below for the RX factory pot settings.

Verify the settings after you are done before you fly the Genius CP.

I use the settings listed below for 3 axis and 6 axis mode. Some people like to use different settings for the two different modes.




SWASH - 1-NRM

STMOD - MODE2 if you want the throttle on the left stick

REVERS - None, all normal

TRVAD - Pitch L & H = 65% to 70%

SUBTR - ALL 0.0%

DREXP - Set D/R and EXPO to your personal needs/preference. Here is what I use.

ELEV D/R 80% EXP +30%

AILE D/R - 80%, EXP +30%

RUDD D/R - 100%, EXP -2%



THHLD - STATE - ACT
POSIT - 0.0%

Set throttle trim to center.



GYRO - MODE- AUTO

Set as high as you can go without getting tail wag. If you get tail wag with these numbers lower them
all equally EX: 78.0%, 78.0%, 78.0%


NORM - 82.0%

ST 1 - 82.0%

ST 2 - 82.0%

THHLD - This doesn't function on the Genius. Leave it where it is set to.



THCRV

To be able to set a value for a Throttle Curve you need to change STATE - INH to ACT



MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
I selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.


PL = 0.0%

P1 = INH

P2 - INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%



MODE - ST-1

Set EXP to OFF


PL = 100.0%

P1 = INH

P2 = INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%




MODE - ST-2

Set EXP to OFF


PL = 100.0%

P1 = INH

P2 = INH

PM = 100.0%

P3 = INH

P4 = INH

PH = 100.0%



PTCRV

To be able to set a value for a Picth Curve you need to change STATE - INH to ACT


MODE - NORM

Set EXP to OFF

SRVHD - It appears this stops the servos or throttle on the helicopter from moving while you are in the program menu. When you exit they function again.
I selected YES then pressed ENT. If you want to work with the values and have throttle and servos working select NO then press ENT for SRVHD.


PL = -35%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%



MODE - ST-1

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%




MODE - ST-2

Set EXP to OFF


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%



MODE - THHLD

These settings will help minimize damage in a crash as the swash and blades will be at mid stick zero degrees pitch.
This will also prevent a boom strike. The swash does not move with TH with these settings.
There is no autorotation for the Mini CP helicopter. If you want control of the swash in TH to help you land in a crash then don't use these settings. Use the setting up pitch curves settings below.


PL = 0%

P1 = 0%

P2 = 0%

PM = 0%

P3 = 0%

P4 = 0%

PH = 0%



If you are setting up pitch curves use these settings first then switch to the settings above for when you fly.


PL = -100%

P1 = INH

P2 = INH

PM = 0%

P3 = INH

P4 = INH

PH = +100%




Here are setup videos I made.
Substitute my settings in the videos for the ones you want in the setup guides.

Walkera Devo 7 TX - Menu Navigation (3 min 54 sec)

Walkera Devo 7 TX - Setup Part 1 (2 min 5 sec)

Walkera Devo 7 TX - Setup Part 2 (3 min 0 sec)

Walkera Devo 7 TX - Setup Part 3 (4 min 49 sec)

-