Some of my planes - RC Groups

Reply

This thread is privately moderated by propjobbill, who may elect to delete unwanted replies.

Aug 26, 2009, 04:24 PM	#1
propjobbill Registered User USA, OH, Oberlin Joined Oct 2004 445 Posts	Some of my planes I will continue to post some of my planes; I have about 50 or 60 airplanes counting my control line planes Images View all Images in thread Views: 236 This is a size 40 Tower Trainer recovered and converted to be a tail dragger Views: 191 This is a scratch built 78" Glider similar to a plane called Wind Drifter. It has A brushed geared Electric motor. The original plane was built in the early 80"s But the wing was rebuilt in the 90's Views: 209 30" shoulder wing with a foam board flat plate under cambered wing. Scratch built from Dollar Tree foam board. Has a Tower Pro 2408-21T brushless motor with an 8x6 DD GWS prop and is a real nice flying plane for relaxed sport flying. Views: 219 This is another Dollar Tree foam airplane with a brushed Johnson 250 motor turning a 10 x 6 prop. This is also scratch built The way I wanted it. Views: 161 Another High wing trainer with a Super Tigre 40 engine Views: 147 Extreme Stick 61.5" wing span fully aerobatic airplane Views: 245 42" Control line plane built and designed from scratch. It a good sport or trainer plane. It has a n old K&B .35 engine Views: 162 Scaled down version of Sig LT. It is 31" wing span Scratch built from plans, with a Cox Sure Start .049 engine. The engine has been slightly modified for about 3,000rpm more, and has a homemade muffler Views: 170 Goldburg Falcon 38" Scratch built from a set of plans. It runs a Cox Sure Start .049 engine; the engine has been modified to include a muffler, throttle and again about 3,000 rpm more than from the factory Views: 156 30" foamboard shoulder wing airplane, made from Dollar Tree foam. It has a brushless motor on a 2 cell Lipo. I love building and flying these little planes they build in a few hours and fly real nice. Views: 176 23" version of Blu-Baby with brushless motor. It is built from foamcore. Flies good in slight wind less than 5 mph Views: 191 23" similar to the blu-baby but it has a flat plat wing with no under camber. It as you can see is a profile plane Views: 175 30" plane everything is made from dollartree foam board. The wing is a sheet folded back to create airfoil at the top and a flat bottom. This makes the wing very strong and stiff without using a stiffener. the ailerons are made of balsa. I also glued Views: 138 38" Goldburg Jr Skylark with a Cox Dragonfly .049 engine. Have not yet made maiden flight. It has rudder, elevator, ailerons, and throttle. Scratch Built from plans. Views: 155 36" Scaled down LT40, built from plans has a Cox Dragonfly .049 engine. The plane has throttle, elevator, rudder, and ailerons. This plan also has not been flown yet. Views: 139 56" Stunt 40 Evolution this is an ARF I have flown it about 5 or 6 times. I don't like the way it flies. They did a poor job of building it very heavy and far out of balance. It has been crashed once already. It is now history the wing came off in fl Views: 185 52" Control line plane with an Enya 35 engine. It flies great and will turn on a dime. Built from scratch with out plans Views: 200 36" Coroplast control line built from scratch without plans. Flies great for sport or trainer, but not a plane you would fly in a stunt contest. Has over 200 flights on it Views: 142 47" control plane with a McCoy 19 engine Great sport plane almost jumps in the air take of less than 6' Views: 187 48" Coroplast stunt plane. I love the way it flies . Looks nasty from lack of cleaning over 250 flights on it. The bonus is it is almost indestructible. Total scratch built without plans Views: 173 71" Sig Cub built from a kit 40 years ago. Recently repainted a few years ago. Views: 180 30" high wing with a KFM2 wing with 50% step with the fuselage formed after the order of a Blu-Baby. I build the fuselage different, wider and made from Dollartree foamboard using a brushless motor. This plane is history, foam planes don't have a rea Views: 167 36" low wing I call a sweet stick. it has a Cox dragon Fly engine. Views: 188 36" control line trainer with an Enya 35 motor Views: 93 Views: 105
	Last edited by propjobbill; Sep 06, 2010 at 07:36 PM.

Sign up now to remove ads between posts

Reply

Return to propjobbill's blog

DRIVE / FLY / SUPPORT

Thread Tools
Show Printable Version Email this Page

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Discussion Gap b/w fuse and leading edge of the wing on two of my 3DHS planes	rballz	3D Flying	5	Jul 26, 2008 10:35 PM
My planes	Morris	Fuel Plane Talk	2	Nov 11, 2002 09:40 PM
My planes seem to fly easier when power off ?	Flyfan	Parkflyers	11	Sep 28, 2002 09:56 PM
My planes	jeffhines	Fuel Plane Talk	4	Sep 23, 2002 08:03 AM
What type of scale should i buy to weight my planes???	JStory	Electric Plane Talk	2	Aug 08, 2001 04:01 AM

Terry, transmitting

All RCGroups content copyright © 1996 - 2013 by RCGroups.com.