|Apr 03, 2009, 06:22 PM|
BB J3 Cub
Presenting the BB J3 Cub. This plane was my entry in the BB Tribute Contest, but was not finished by the dead line. In fact it has taken me a 3 months since then, because of more pressing issues. The plane flys better than my 42" RET BB, I built this one with ailerons, my first. I have a vid of it flying for about a minute before the batteries ran out of juice and I hit a tree. Remember to always charge your batteries before you go fly.
Here is the vidio of the maiden flight.
Ok, I finished the plans for the BB J3 Cub. See below.
The specs are;
Wing span = 44"
Wing area = 413.5 square inches
Fuse length = 29.5 inches
Motor = Emax 2822, 1200kv
Prop = 9x3.8
Esc = Simple 18 amp
Receiver = 9 gm, 6 channel
Servos = 9 gm, qty 3
Battery = Lipo, 1000 mAh, 20c
Wheels = D75xH18mm
Landing Gear = Made from bent coat hanger
Auw = 19 oz.
Construction material = Dow PBIII fan fold foam
The BB J3 Cub uses the same monoblock construction as the BluBaby, so for assembly instructions I would suggest you check out that build thread.
If anyone wants to build one of these and has a specific question, just let me know here and I'll do my best to answer it.
ImagesView all Images in thread
FilesView all Files in thread
|Apr 11, 2009, 07:34 PM|
I plan to put a post on the BluBaby thread and the old tribute thread after I get everything into my blog. A little less pressure this way. I finished the plans, so I just have to make all the pdf files for them. It's supposed to rain tomorrow so I will get it all together and post it then.
|Apr 12, 2009, 02:58 PM|
You did a very nice job on those plans (very thorough). I have a question though. What does "D size" mean on your file name above? Does it need to be scaled to be 44"? Thank you for posting the plans. It looks like a very good flyer in your video. Congratulations.
|Apr 12, 2009, 03:22 PM|
D-size drawings are 34" wide x 22" high, so if you have access to a large format plotter you can print it out at 1:1 on two sheets of paper. I have one at work, but only printed it out at 8.5" x 11" for reference and used the tiled pdf to make my cub. I wanted to test the tiled version of the plans since that is what most people will use.
Foamenator, Thanks for the complement. I will probably build a 34" kfm2 version for use with a blue wonder motor.
|Apr 12, 2009, 06:47 PM|
I used apple barrel craft paint form Walmart, bright yellow. It is very opaque. I had to use several coats to cover the blue evenly. Next time I will put on a white base coat to see if that will reduce the number of coats required. I mixed it 50/50 with rubbing alcohol, each coat dries fairly quickly that way. Also need to try to remove as much of the black printing from the foam as possible before painting. It rubs off of the packing tape very easily, so you should try to scuff the tape up with sand paper before painting.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Pico j3 cub||Havens54||Foamies (Kits)||2||May 05, 2002 05:44 AM|
|GP J3 Cub Finally in the air!!!||drc||Scale Kit/Scratch Built||30||May 04, 2002 08:41 PM|
|FS: RTF J3 Cub :JR 421 Radio+Receiver||fchristian||Aircraft - Electric - Airplanes (FS/W)||1||Feb 16, 2002 01:40 PM|
|Who sells the GWS J3 Cub FL||Der Zip||Parkflyers||3||May 24, 2001 08:30 AM|
|hangar 9 j3 cub 100"||jsc||Electric Plane Talk||9||May 20, 2001 12:36 AM|