http://www.hobbyking.com/hobbyking/s...ner_Motor.html

This one maybe? Close to the omega 103g

I wish this was a two piece removable wing. I bet the chances of thie twist, warp would be greatly diminshed during production. It would also be super easy to transport.

That's what I was confused about I couldn't find the motor I have on hobby king, the one you linked is a D3530 1250kv and the one I have is a C3530 1100kv.

Originally Posted by 3DHSISEPICS

That's what I was confused about I couldn't find the motor I have on hobby king, the one you linked is a D3530 1250kv and the one I have is a C3530 1100kv.

This motor is pretty darn close to the omega 72g.

http://www.hobbyking.com/hobbyking/s...dProduct=18160

And I think the motor you have(C3530) is discontinued because I can't seem to find just the orange/yellow turnigy motors anymore. I think they have been replaced with this line.

http://www.hobbyking.com/hobbyking/s...URNIGY_XP.html

Another close match to the 72g omega.

http://www.hobbyking.com/hobbyking/s...ner_Motor.html


All of these motors seem to have less power than the omega however.

According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...

Originally Posted by Da Big_G

According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...

What prop are you using and with what motor? You might want to try a prop with less pitch. I have a little zaggi that had too much pitch and when I punched the throttle it would roll real bad.

Originally Posted by Da Big_G

According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...

Whats your setup, Motor, prop, servos?

Originally Posted by Da Big_G

According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...

me too, flys like s$%^

omega 72g, 11x5.5 prop, hs-65mg all around

Originally Posted by Da Big_G

According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...

Mine has gotten better after twisting but still has the roll issue some at higher speeds. A little ways back in the forum we talked about a epp sbach that is really good. Might want to check it out. The hokusei sbach 342.

Originally Posted by jsmith285

Whats your setup, Motor, prop, servos?

Turnigy D3536/8 1000kv. motor
Turnigy 45a SBEC speed control
APC 12-6E prop
Turnigy 3C/1600 ma battery
HiTech HS-65MG servos all around.

My setup:
Motrolyfly 2810-1000 12x6 apc
HS65 MG tail, HB wing
Ice 50 w.new gens 3s 1300 25c
Built it the same was as my 34 extra EPP, 38 slick EPP and 48 Extra full EPP.

Honestly, I didnt take the time to twist (b/c I figured it was a patch at best), I took took the electronics out and dumped em in a 47 SHP. I was dissappointed, but you can't win em all.

Originally Posted by Da Big_G

Turnigy D3536/8 1000kv. motor
Turnigy 45a SBEC speed control
APC 12-6E prop
Turnigy 3C/1600 ma battery
HiTech HS-65MG servos all around.

Well part of your problem is the 12x6 prop. Seversl have reported that prop will cause more roll problems. Try a 11x5.5e.

Originally Posted by nickelbn1

Well part of your problem is the 12x6 prop. Seversl have reported that prop will cause more roll problems. Try a 11x5.5e.

I don't think a smaller prop. is the answer. The roll is present in a low/no throttle down line. Only after some air speed bleeds off does the roll cease. BTW, I need considerable aileron trim for low speed flight. I was holding out for corrected wing to be available, but that is not going to happen. Not going to waste any more time on this one. I think I'll chuck it into the trash.

Originally Posted by nickelbn1

A little ways back in the forum we talked about a epp sbach that is really good. Might want to check it out. The hokusei sbach 342.

That's the 39" BX or V2 and it's wonderful! Unfortunately, they are out of stock at F3A Unlimited but BestRC has the red ones in stock.

It's Wednesday! Yay! Time for our weekly, after work, fun fly at the park. I brought the Edge, Sbach, Crack Pitts, Fishcopter (my quad) and many batteries.

Originally Posted by dentalpain

My setup:
Motrolyfly 2810-1000 12x6 apc
HS65 MG tail, HB wing
Ice 50 w.new gens 3s 1300 25c
Built it the same was as my 34 extra EPP, 38 slick EPP and 48 Extra full EPP.

Honestly, I didnt take the time to twist (b/c I figured it was a patch at best), I took took the electronics out and dumped em in a 47 SHP. I was dissappointed, but you can't win em all.

That SHP is a pretty plane. Flown it yet?