HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Apr 02, 2013, 03:23 PM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
Discussion
Covering

This is my first kit, my other balsa planes have been ARF with monokote.
I have covered the rudder with ultracote and that seemed fairly easy, I just used one piece on each side, overlapped the edge and sealed. With the wings, how may pieces should be used to complete the covering? I was thinking that I would need to cover the tips with one piece and the body of the wing with another piece wrapped from the TE up and over the LE and back to the TE.
jk6672 is online now Find More Posts by jk6672
Reply With Quote
Sign up now
to remove ads between posts
Old Apr 02, 2013, 10:41 PM
Registered User
Joined Dec 2009
7 Posts
Everyone has a different method, it depends on what works best for them.
here's a decent youtube of covering with Monokote and you'll see a part II on the side.
Monokote 101 Part I.mov (5 min 43 sec)

Hope it helps
chetterb is offline Find More Posts by chetterb
Reply With Quote
Old Apr 02, 2013, 10:44 PM
Registered User
Joined Dec 2009
7 Posts
Monokote 101 Part II.mov (4 min 6 sec)
chetterb is offline Find More Posts by chetterb
Reply With Quote
Old Apr 02, 2013, 10:45 PM
Registered User
Joined Dec 2009
7 Posts
Monokote 101 Part III.mov (6 min 55 sec)


hope these help
chetterb is offline Find More Posts by chetterb
Reply With Quote
Old Apr 10, 2013, 08:09 PM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
Thanks. Haven't done the wing yet, but I have finished the tail:



jk6672 is online now Find More Posts by jk6672
Last edited by jk6672; Apr 10, 2013 at 08:18 PM.
Reply With Quote
Old Apr 14, 2013, 09:24 AM
Another Newbie
United States, PA, Bethel Park
Joined Feb 2013
9 Posts
what setting was your heat gun on. i tend to burn holes on high and don't have enough heat on low.
poolman1950 is offline Find More Posts by poolman1950
Reply With Quote
Old Apr 14, 2013, 09:54 AM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
Quote:
Originally Posted by poolman1950 View Post
what setting was your heat gun on. i tend to burn holes on high and don't have enough heat on low.
I started out around 225 tacking and worked up to around 300. I've burnt holes too, but with monokote and heat gun on high.
jk6672 is online now Find More Posts by jk6672
Reply With Quote
Old Apr 14, 2013, 10:14 AM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
I’m almost finished with the wing. I originally wanted to put LED lights, but then I changed my mind because I've never soldered something this small before (a servo lead or two, but that's different). I Since decided to go for it, because I knew if I didn't give it a try I'd be kicking myself in the butt latter.









I know the directions state to cover first, before putting the wing halves together, but I bonded them already so there wouldn't be a seam in the middle.
jk6672 is online now Find More Posts by jk6672
Reply With Quote
Old Apr 16, 2013, 09:32 PM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
Soldering the LED's turn out not to be the difficult task I thought it would be. I finished one row tonight and tested, looks nice. I'll post a video once I'm finished.
jk6672 is online now Find More Posts by jk6672
Reply With Quote
Old Apr 18, 2013, 10:02 AM
Registered User
United States, CA, Heber
Joined Sep 2012
1,335 Posts
finished the LED's and covered, but this photo is before covering.



jk6672 is online now Find More Posts by jk6672
Reply With Quote
Old Dec 28, 2013, 12:05 AM
MigLovin'
Sanford, FL
Joined Dec 2008
66 Posts
did you ever get the video you mentioned in the previous post?
JimEdmiston is offline Find More Posts by JimEdmiston
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale Eflite extra 260 balsa version CUSTOM COVER xtremetoyz Aircraft - Electric - Airplanes (FS/W) 1 Jun 16, 2013 03:06 PM
Sold fairings, servo covers w/bumps & fairings, bump covers dhauch Aircraft - Sailplanes (FS/W) 11 Feb 02, 2013 05:51 PM
Discussion 18" Albatros covering question richb77uk Scratchbuilt Indoor and Micro Models 2 Jan 07, 2013 03:46 PM
Found Aspire covers J. Wydronek Aircraft - Sailplanes (FS/W) 4 Jan 05, 2013 03:05 PM
Question Covering Irons jim19 The Builders Workshop 2 Jan 02, 2013 09:30 PM