Joined Dec 2011
450 Basics [ stuff you need ]
Wow - so what do you need to fly a 450 .. Since this is posted in the beginner section of the forum , I will assume Noobness ...
First you need your heli and radio [ I will assume RTF to speed things along ] , and RTF can be had from $125 or so shipped to your door . [ Depending on where in the world you are ]
The first thing I would recommend is a Charger , iMAX B6 [ Can be had from about $19 ] , power supply [ $10 ] , maybe a Parallel charging board ? [ $9 if you want to charge more than one battery at a time ] A B6 with a built in power supply will start around $34
Batteries ? one is not enough ...
Tools = Hex drivers 1.5mm / 2mm / 2.5mm / 3mm [ you want 2 x 1.5mm ]
Pliers , standard and ball link , $5 each
Zip ties ...
Screw drivers [ phillips ]
Heli spares :
Hmmm , well , just depends on what your breaking ..
Main drive gear
Main rotor shaft
Feathering shaft [ make sure you get the right ones ]
Tail rotor shaft
Oh yeah - Rotor Blades ...
Servos [ I really like the TG9e from HK , cheap and good , a rare combo ]
Frame screws [ one bag should be enough ]
If you can live with one helicopter you wont need so many spares [ maybe ] , pictured is my nick nack boxes , the small stuff ..
Screws , motor mounts , feathering shafts , main shafts , tail rotor shafts , and so forth .. The more I got in , the more parts I needed , the deeper I got ..
At one time it took almost 2 months to get rotor blades out of China , local blades cost like $15 or more for a single pair , now I carry a few pair , well eeer , Im not sure ... Let me check ... Yikes , maybe more than your local hobby shop .. Thing is , I dont want to wait for spares .. Id rather get to one or two spares and order more than not have any .. I might go a month now without breaking anything , and suddenly there is a oops moment , and you need new rotor blades , feathering shaft , main rotor shaft and maybe a servo or three ..
A really huge oops might see you replacing 50% of your bird ..
Do you twiddle your thumbs for a month waiting for parts , or do you sit down , repair the heli and kick yourself for doing something silly and keep flying ?
Anyhow , parts , how much etc is very personal , but you should keep some , especially the more common parts that are bent or broken ..
Main drive gear , main rotor shaft and feathering shaft , these 3 things are probably the most common to go , with servos next ..
Thing is , once you carry spares - youl break something you dont have - Murphys Law ...
United States, VA, Fluvanna
Joined Jan 2011
I keep my spare parts in boxes now. I have spare servos (when you get your cyclic servos order 4 because when one strips you will end up replacing all 3 if you cannot get the exact same one to replace it).
Also, keep 5-10 flybars in stock. I bend them during transportation to a flying site or back home sometimes since I don't have a carrying case for all of my 450 helis.
QC on the cheap main shafts is pretty bad. Expect some to be slightly bent.
Not only 2 short 1.5mm hex drivers but also a long one.
A magnetic parts tray for holding those tiny screws and washers.
A couple of drive belts. They stretch and have to be replaced eventually.
A spare set of tail blades in case of a tail strike on the pavement. I have hit little pebbles while landing in the grass or on cement sidewalks with pebbles in the concrete.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Question||If you wish to charge the included battery from an AC power source, you will need the||mikeydrc||United Kingdom||5||Jan 28, 2013 05:52 PM|
|Sold||Cleaning out stuff I don't need. Airplane stuff||Ifly101||Non R/C Items (FS/W)||4||Jan 27, 2013 07:32 AM|
|Sold||(Last re-list, Reduced) Basically Brand New TREX 450 Sport BNF $315 Shipped||nautique||Aircraft - Electric - Helis (FS/W)||2||Jan 09, 2013 01:35 AM|
|Sold||(Reduced) Basically Brand New TREX 450 Sport BNF $325 Shipped||nautique||Aircraft - Electric - Helis (FS/W)||0||Jan 02, 2013 02:13 PM|
|Basic 3dx stuff, what I need.||lift off||Foamies (Kits)||1||Aug 12, 2004 04:33 PM|