I ran a test with a dummy load on the foxtec tx, that means I DIDN'T have ANY antenna mounted on the transmitter,

Note that Vtx leak an appreciable amount of power from the case/wiring, in the -40/-30dbm range. That amount vary greatly with the position of the Tx so it may not give consistent results. Using a 30db attenuator and an antenna for a stable -7dbm emission is more accurate, but a longer walk

-Hugo

Im interested in 1.3

Originally Posted by nakelp86

Im interested in 1.3

actually 900 -1.3 are easy, It's hard to make them commercially viable...


www.fpvlr.com - your custom fpv antennas

well I am in need of REALLY tuned set, I have few from one of our antenna guru but they do not perform as they suppose to :-((
Need for low distance flying, what would be the best set?

Originally Posted by nakelp86

well I am in need of REALLY tuned set, I have few from one of our antenna guru but they do not perform as they suppose to :-((
Need for low distance flying, what would be the best set?

I have gone 12km with a set of 1280 pinwheels.... but your mileage may vary...

how far do you need to go? This way I can tell you if you are ok with omnis or you need a helical on the ground.

Also what is the area you fly in? Is it rural or urban? How high do you fly when going far?


www.fpvlr.com - your custom fpv antennas

Originally Posted by Hugeone

Note that Vtx leak an appreciable amount of power from the case/wiring, in the -40/-30dbm range. That amount vary greatly with the position of the Tx so it may not give consistent results. Using a 30db attenuator and an antenna for a stable -7dbm emission is more accurate, but a longer walk

-Hugo

I noticed it leaks RF I just didn't know how much, to be able to calculate what kind of attenuation I am getting with a dummy load, but all it takes is one other flight to make up a usable ratio...

Exciting times ahead. I am going to refine the Lindenblad and also a 5.8 phased array...

www.fpvlr.com - your custom fpv antennas

Hello Mr. F
your 10 sets with rg-58 coax and adjustable bends are pretty much ready, need to make 2 more
will be shipped out on monday!
Thank you for the large order!


WWW.FPVLR.COM - YOUR CUSTOM FPV ANTENNAS

Originally Posted by KondorFPV

I don't feel like spending 500$ just to get into the vendor's forum. I think there are other threads just like this, including circular wireless , dragon link, mfd tracker...just to name a few, and people here just like in those forums can share their opinion about these products and it's a way for fpvlr to keep in touch and provide customer service. After every post it takes just a couple hours and the thread gets bounced back in the second, third or fourth page. So I don't see it as a problem. Vendors need a bit of visibility, and you get NO visibility in the vendor's forums.
It's best to have only 1 thread with everything regarding fpvlr.com, which is development, new products, customer support, customers' questions, than have 100 threads with a little bit of info in each one...because that's what customers would resort to, writing a new thread for each question etc.... A thread like this is a way to keep things neat.

It's still against the rules. I'd imagine the vendors section was created for a reason. This thread was created by a vendor purely for commercial reasons. Anyway not my issue - just pointing it out. Here is the forum rule that pertains:

We allow one advertisement per week per forum per user. An advertisement is any content designed to sell or publicize an event, good, or service. Note that certain areas of the site (including the classifieds and vendor sections) are exempt from this rule.

Originally Posted by BrettAltea

It's still against the rules. I'd imagine the vendors section was created for a reason. This thread was created by a vendor purely for commercial reasons. Anyway not my issue - just pointing it out. Here is the forum rule that pertains:

I read the rule, and I will limit my advertisement to 1 per week as the rule states. Actually I thank you for pointing it out to me.

Frank,
3 sets of 1.2 heading your way!


WWW.FPVLR.COM - your custom FPV antennas

John, here are your 5 sets 5.8 rg-316 for you and your friends, heading to NY.



And with these, I am back on top of orders...

First come, first serve


WWW.FPVLR.COM - Your custom fpv antennas

How do you make a custom order? Flexible cable, rp-sma, etc

Originally Posted by Ceros007

How do you make a custom order? Flexible cable, rp-sma, etc

Hello Ceros, connectors and frequency can be chosen from the order window when adding to cart. But custom orders, like LHCP etc can be specified in the PAYPAL notes.....

Let me know if you have more questions.

Hello Miro972...
your 1320 mhz set is ready to ship --- on monday!

www.fpvlr.com - your custom fpv antennas

Hello Mike,
this 5.8 ghz set is heading to Virginia...
I have test flown the tx antenna to 9 +Km using a lowly 4.25 turn helix (all the way to the very edge of video link- video coming shortly) and it's performing as expected, so your set is heading to Virginia.


www.fpvlr.com - your custom fpv antennas.