Originally Posted by vhoward1122

When I started in RC, there were no computer radios. So you had to set every plane up properly mechanically as there were no model memories to remember trims and sub-trims.

Ditto. Maybe that's why we have "good luck" with the radio?

Originally Posted by exciter900rr

Ditto. Maybe that's why we have "good luck" with the radio?

Yup but if it was not for these radio's I would not have come back to the hobby, so yea I appreciate what you "old timers" have gone through to assist us newbies, and returning newbies in the hobby.

If it was not for you giving feedback to the manufactures, folks like us would not be where we are today!

Thank you!!!!

-S-

Originally Posted by Xnaron

Just upgraded my Aurora and module without any issues.

Mike - I'd like to get the deadband issue on my Aurora 9 fixed. Are we able to send them in for repair yet? I know Hitec was working on a solution and we were supposed to hold tight until it was announced.

thanks,
Brendin

Hi Mike,

I too am wondering if you can give us an update on the resolution of the deadband issue. I trust you guys are still working on it and it hasn't dropped off the radar? Myself, and at least 3 other flyers I know with A9's have the issue (to varying degrees), and they all come to me for updates on when a fix will be available.

My A9 mainly has the deadband on low throttle (Mode 1), about 3-4mm. While it is not stopping me from flying, it is definitely annoying (and a sourer point on an otherwise brilliant radio).

Thanks,
Steve

When we see in shops receiver's Hitec MINIMA 5 ??

I have noticed a remarkable problem after the last update to 1.07, and 2.0: My switches are out of order! I noticed this after flights yesterday, when I wanted to switch on the lights - no function! Ad home I tested it and found out, that the lights are on, if I give full left aileron! How could that be? Before the update everything worked fine.

I tested all the other switches - no function either!

Now I switch my lights on and off with a slider - that works. What happened? Do you have the same problem?

Udo

How bizarre! I have not noticed this on my setups.

May be a good idea to back up all models before running an update and then reloading them then rebind.

Originally Posted by udogigahertz

I have noticed a remarkable problem after the last update to 1.07, and 2.0: My switches are out of order! I noticed this after flights yesterday, when I wanted to switch on the lights - no function! Ad home I tested it and found out, that the lights are on, if I give full left aileron! How could that be? Before the update everything worked fine.

I tested all the other switches - no function either!

Now I switch my lights on and off with a slider - that works. What happened? Do you have the same problem?

Udo

Anyone else?

Glad I have not updated.

That is good and wacky udogigahertz, your A9 must have caught the same crazy 1.07 upgrade gremlins mine did!

I just have tried to get rid of that "bug" by doing the update again - start from the beginning with the new HPP-22-software (now it is version 1.02), before that I changed my computer settings to "English - USA", made all the updates again - no improvement, no switch is functional!

Maybe I should try to downgrade the software first?

Udo

realized my error in above statement...I have NOT seen this issue on my radio.

Originally Posted by angelfood

Anyone else?

Glad I have not updated.

Hey guys are you losing the programming on the switches, or have they stopped working altogether.
Apparently we are still having a few teething pains.
I am still on 1.06 and will stay that way for a while.
When I do upgrade I will backup my models.

Originally Posted by zero2444

Hey guys are you losing the programming on the switches, or have they stopped working altogether.

The last is the case ...... no switch works anymore!

Udo

No problems with the the upgrade. I only did the TX and Module, though. I updated the HP-22 software, first, and then did the firmware upgrades.

The values are not changing after the 1.07 upgrade, it seems the software has changed on how it interprets the data. My one sailplane the FLP2 servo reversed but my FLP servo the travel changed (not the EPA values). I used to have 140 up and 140 down EPA and I had to change it to 140 up and 87 down. I really don't trust what has happened and was planning on trying a new model to see where the travel actually ends up.

Originally Posted by udogigahertz

The last is the case ...... no switch works anymore!

Udo

Just a thought: did you try reprogramming the switches again to ensure that they are not in "null"?