 |
 |
|
 |
 |
 |
Oct 02, 2012, 05:59 PM
|
|
United States, WV, West Hamlin
Joined Nov 2006
155 Posts
|
Futaba 10CG Servo End Point help needed
Hello Everyone,
I need a little help on adjusting my "End Points" on my radio. I can find all the main channel adjustments but not on the Aux-Ch's, I have one of my Ch's set up on the lever switch (VR (E) ) but can't find where to adjust it, I've looked in the manual also. I can find them for the toggles and sticks but not knobs and lever switches. Thanks! |
|
|
|
|
|
Oct 03, 2012, 09:52 AM
|
||
|
Champaign
Joined Apr 2003
141 Posts
|
Are you in 7ch mode or 10ch mode in your transmitter?
Sincerely, Krysta Product Development & Support Specialist Futaba Service Center USA service@futaba-rc.com Quote:
|
|
|
|
|
|
|
Oct 03, 2012, 10:01 AM
|
||
|
United States, WV, West Hamlin
Joined Nov 2006
155 Posts
|
Quote:
|
|
|
|
Last edited by Rick~K; Oct 03, 2012 at 10:06 AM.
|
|
|
Oct 03, 2012, 12:29 PM
|
||
|
Champaign
Joined Apr 2003
141 Posts
|
On the main screen in the upper right hand corner directly below 2.4G, it should say either 7ch or 10ch.
But either way, in either 7 or 10 channel, when you go into the End point screen, toggle down to your Aux channel, it should show L or H, if you have that channel set to a dial. You should then be able to turn the appropriate dial or move the appropriate slider to adjust both sides of the end points. What are they set to in your Aux channel menu? Also, have you tried going into a blank model to see if you can set the end points in a completely new model? Sincerely, Krysta Product Development & Support Specialist Futaba Service Center USA service@futaba-rc.com Quote:
|
|
|
|
|
|
|
Oct 03, 2012, 02:08 PM
|
|
The Northeast Kingdom, Vermont
Joined Jun 2004
4,795 Posts
|
Rick,
Are you trying to use either channel 9 or 10 for this function? These channels do not have an endpoint or sub-trim adjustment, as they're only switched on/off channels. Pete |
|
|
|
|
Oct 03, 2012, 02:51 PM
|
|
|
United States, WV, West Hamlin
Joined Nov 2006
155 Posts
|
Ok, That worked.. Thanks!!! I was setting my Ch8 that was Aux8 on end point adjustment. I was thinking that was one of my NAZA gain adjustment ch's but they are Ch6&7. I'm new to this radio, my first Futaba since my J series in the 80's and I'm using it for UHF... love the Radio.
Thanks Again Krysta and Pete! |
|
|
|
|
Oct 09, 2012, 04:51 PM
|
|
|
United States, WV, West Hamlin
Joined Nov 2006
155 Posts
|
Krysta, or anyone
Is there a way to disable 2.4 transmit on the 10CG? I'm using it for EZUHF and the manual for UHF says to disable the transmitter (10CG) so both UHF and 2.4 is not transmitted at the same time. Thanks! |
|
|
|
|
Oct 09, 2012, 05:53 PM
|
|
|
The Northeast Kingdom, Vermont
Joined Jun 2004
4,795 Posts
|
It's covered on page 17 of the manual. It's the option just below the range test power down option
 Pete |
|
|
|
|
Oct 09, 2012, 05:54 PM
|
||
|
United States, WV, West Hamlin
Joined Nov 2006
155 Posts
|
Quote:
|
|
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Question Tail Servo Arm / Gyro / End-Points | Blade Crasher | Electric Heli Talk | 1 | Sep 28, 2012 07:28 AM |
| Question Hitec servo programming, center and end points | tb47 | Radios | 4 | Jun 24, 2012 07:30 PM |
| Discussion Need Help! Futaba 10CG 2,4 | hypstar | Radios | 7 | Jun 07, 2011 10:13 AM |
| Help! Futaba 10CG - problem with end point adjustment | Szymon Bartus | Radios | 0 | Sep 01, 2010 04:14 AM |
| Discussion Futaba 12FG: Relationship between Servo Travel and End Point | heliatom | Radios | 1 | Apr 04, 2010 10:04 PM |
|
|