|Oct 13, 2012, 04:31 PM|
Shielded NAZA and WKM GPS Protectors
I built this device after one of my LI-po Batts died in mid-air. The quad rolled over and landed directly on the GPS device and shattered the ant inside. I had to purchase another NAZA GPS to replace it for another $160 +-
Another thing that annoyed me was that the OEM stand had to be glued in place so if it ever broke I had to search all over to find a replacement. If you glued the device it was also a pain to rotate it when you moved to different geographical locations.
So I designed the GPS protector. This device provides protection for your WKM or NAZA GPS devices, Allows rotation up to 360%. Gives you a place to coil the wire that connects the GPS. Also is easily replaced and mounted (Only one mounting hole is needed)
2 inches high or more if requested
Due to numerous requests I have started offering copper shielding
Shown at -8% rotation
Only one bolt to mount the device
Replacement parts are only $5.00 each shipped in USA
I have versions for the NAZA gps and the WKM (Make sure you stipulate what version you want in your paypal payment)
$10.00 shipped in the USA for non-Shielded
$15.00 shipped in the USA for Shielded
Please use Goods for paypal payments
Patent Pending 61/705,406
|Oct 14, 2012, 03:34 AM|
Joined Dec 2010
Trader Rating: 10
That copper shielding around the sides very much affects the tuning of the GPS antenna in a bad way. You may only notice in frnge areas but you will notice. If the shielding were made such that it were only at the bottom of the antenna it would cause no ill affects and might help a little as far as RFI shielding goes. Shielding on the sides though not good.
Nice product otherwise. I'm planning on getting a couple.
|Feb 08, 2013, 02:15 PM|
Not being a smart ass I seriously want to know
|Feb 08, 2013, 02:33 PM|
No experimental evidence--just theoretical. I recently purchased a MR that came with the Naza GPS and this mount w/ copper. I removed the copper from it, though. I like the mount, otherwise.
The copper is a partial Faraday cage around the receiver, and GPS signals come in from angles as low as the horizon. Some of those signals will be blocked by the surrounding copper on the sides. As to how much this will affect real-world performance of the GPS, I don't know. But I don't see it helping. Since GPS operates in the 1.2-1.6GHz range, you're not going to get any interference from 2.4GHz radios, and the engine noise is very low frequency compared to the GPS so it's not going to cause any problems either.
|Feb 08, 2013, 02:39 PM|
My theory is that it will not help with our usual 2.4 or 5.8 RF but many are using lower freq like 1.2, 1.3 and one device I keep hearing about it helping with is the gopro. I cannot seem to find anything about what freq would be coming from it. I wouldn't think the gopro would cause any issues but enough people are saying it does to warrant a look
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|For Sale||DJI NAZA GPS Protector||wdelarme||Aircraft - Electric - Multirotor (FS/W)||145||Nov 09, 2014 07:35 PM|
|For Sale||DJI NAZA GPS Protector||wdelarme||Aircraft - Electric - Multirotor (FS/W)||13||Jan 25, 2014 07:20 PM|
|Poll||How many DJI (Naza or WKM) pilots fly primarily in ATT or GPS mode||Adidas4275||Multirotor Talk||30||Sep 10, 2013 10:36 PM|
|For Sale||New shielded NAZA GPS Protector||wdelarme||Aircraft - Electric - Multirotor (FS/W)||18||Dec 17, 2012 06:51 PM|
|For Sale||DJI NAZA GPS Protector||wdelarme||Aircraft - Electric - Multirotor (FS/W)||3||Sep 25, 2012 04:58 AM|