

Nov 30, 2012, 04:20 PM  
Joined Dec 2011
62 Posts

Shoe
Thanks for the pdf. It will take me some time to get a physical feeling for the effect of some of the symboles. I have been doing some crude "hand cranking" and found that "r/2' works all over the cylinder. I do not know yet if I have any starting point for the wing, I am still suggesting that using the Bernoulli equation in traditional streamlines is actualy interigating perpendicular acceleration pressure rather than calculating Bernoulli Principle flow. The velocity changes that we nomally use do not exist in the actual inertial flow. 
Dec 02, 2012, 02:23 PM  

Quote:
Multiplying the radial pressure gradient by "r/2" amounts to "bringing an algebra weapon to a calculus fight". Your approach works in this specific case, but only because multiplication by "r/2" transforms the expression for the radial pressure gradient into an expression for the dynamic pressure. For steady, irrotational, uniformdensity flow, the increase in dynamic pressure from one location to another is equal to the decrease in (static) pressure. Just because an analysis leads to an equation that accurately predicts the relationship between flow parameters (in this case the Bernoulli equation), that doesn't mean the analysis is correct. The are an unlimited number of ways you can arrive at the Bernoulli equation (monkeys with typewriters comes to mind), however, the reason the Bernoulli equation accurately predicts the relationship between velocity and pressure in a steady, irrotational, uniformdensity flow is because it can be derived from conservation of momentum. I have updated the .pdf in the post above to address the issues associated with analyzing the flow around an airfoil (or cylinder) from a reference frame where the airfoil is moving through otherwise still air. 

Dec 03, 2012, 11:43 PM  
Joined Dec 2011
62 Posts

ShoeDLG 
The pdf update is great. I have not seen a like presentation on the subject before. Eventully I may have a couple serious questions but with my limmited math skills I will probably miss some important subtle parts of the derivations. (You would be surprized at the amount of simple algebra I used in years of configurating airplanes !) 
Dec 05, 2012, 06:35 PM  
Joined Dec 2011
62 Posts

Quote:
Fluid texts all show the source/sink pattern and the simple formula for flow velocity relative to the surface. (ideal etc.) I reconsile this with the cylinder V and find the actual instantainious velocity relative to the remote still air. ( v is virtually never at right angles to v') At every location between the stagnation areas the velocity of the flow next to the surface is one V in its source/sink direction. In the direction of its path there is no acceleration and no change in speed. The V we see at the top of the cylinder indicates direction only and not a difference in speed. All pressure change must then come from normal accelerations. The primary acceleration for the cylinder is normal to the true flowpath. Lift is determined by acceleration normal to the surface which is a component of that primary acceleration. 

Dec 06, 2012, 01:02 AM  

Quote:


Dec 06, 2012, 02:39 PM  
Joined Dec 2011
62 Posts

Quote:
Each "e" path is unique to only one element . The following element has its own "e" path. What appears as separating when relative to the surface is the difference in location on their own "e" with different vectors. That difference is made up by the thinning of the larger element as in the continuity law. Bernoulli is only interested in the accelerations of individual elements. Conditions at the stag points is somewhat imaginary as there is convex flow to turn onto an off of the cylinder. The first part of http://svbutchart.com should help. 

Dec 07, 2012, 04:10 AM  

Crossplot,
Still not sure I completely understand where you are trying to go with this. Some additional thoughts: 1. Even though the speed of a particle remains constant (equal to V) on the surface of the cylinder (viewed from the reference frame where the remote air is still), the pressure on the surface (the pressure experienced by the particle) does vary with location. You just need to apply the proper form of the Bernoulli equation to relate the pressure to the velocity (in this case the unsteady form of the Bernoulli equation). This is shown in the attached .pdf. 2. There’s nothing imaginary about the “convex” flow near the stagnation point. Just as you can show that crossing “concave” streamlines to get to the top of the cylinder means the pressure is lower than ambient there, you can also show that crossing “convex” streamlines means that the pressure at the stagnation point is higher than ambient there. 
Dec 07, 2012, 02:33 PM  
Joined Dec 2011
62 Posts

Quote:
1. Pressure changes with the changing normal acceleration as the curvature tightens then relaxes in the "e". I am having trouble making the pdf work. It may just be just me and am needing a diagram!! 2. I was just trying to justify the use of "stagnation point to stagnation point". 

Dec 07, 2012, 03:09 PM  

Your train of thought is difficult to follow because you are mixing reference frames. I'm not sure what you mean by "Bernoulli can not apply", but the relationship:
total pressure = static pressure + dynamic pressure does not apply in an unsteady flow. Are you having trouble opening the .pdf? 
Dec 07, 2012, 05:32 PM  
Joined Dec 2011
62 Posts

Quote:
I plugged 45deg into the first still air equation and came up with zero. I do not believe that there is any way that calculus can squeeze pressure change out of fluid that is not changing velocity. 

Dec 08, 2012, 03:53 AM  

Crossplot,
I was sloppy with the .pdf in post 791. The first "still air equation" is wrong. The "one half" belongs in front of the "v squared" term inside the parentheses, not outside the parentheses. This equation should be the same as equation (57) from the .pdf file from post 781. Sorry about that. I've corrected the attachment. 
Thread Tools  
Similar Threads  
Category  Thread  Thread Starter  Forum  Replies  Last Post 
Discussion  Dymond D47 servo, Which version do you have on hand, how can you tell???  TDboy  Hand Launch  5  Apr 21, 2012 03:26 AM 
Discussion  Is there anything listed that you can't live without?  P51C  Life, The Universe, and Politics  44  Aug 05, 2011 03:55 PM 
Discussion  Fast food that you just can't do without.  Bilbobaker  Life, The Universe, and Politics  101  Aug 17, 2010 12:30 PM 
Joke  What Would You do to get that Aircraft You Can't Have ?  Chophop  Humor  10  Feb 09, 2010 08:00 AM 
Discussion  HELPIf you have a problem that can't be solved here  ccowboyearl  Beginner Training Area (HeliElectric)  2  May 14, 2009 01:31 PM 