New Products Flash Sale
Thread Tools
This thread is privately moderated by JimDrew, who may elect to delete unwanted replies.
Old Apr 05, 2014, 11:09 AM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
I use Artic Silver SCCE. This is a slow cure ceramic epoxy with very good W/mēK rating. But, more importantly is its high temperature handling. CPUs and such don't get to hundreds of degrees like a heat sink can with ESCs. The ceramic handles the heat transfer perfectly. Being ceramic, it's not electrically conductive at all. So, there is no danger of accidentally getting some on a PCB causing an issue.
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Sign up now
to remove ads between posts
Old Apr 05, 2014, 12:08 PM
theKM is offline
Find More Posts by theKM
↓↘→ + (punch)
theKM's Avatar
central PA.
Joined Sep 2004
20,770 Posts
a second for Arctic Silver. it's rather awesome.
theKM is offline Find More Posts by theKM
Reply With Quote
Old Apr 19, 2014, 04:20 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
New updater (updater45.exe) has been released! Includes new firmware for the Nano, Nano II, RFU, and X10+ to support long frame rates used by radios using PPM data with more than 12 channels.

Nano II also now uses the port based outputs instead of channel based outputs. This means that every output can be reversed and/or have an offset position from center.

Changes made for all updates is available on the downloads page, located here:

http://www.xtremepowersystems.net/xd...are%20Upgrades

Don't forget that you need to perform a RESET a device has had its firmware updated!
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Last edited by JimDrew; Apr 22, 2014 at 02:02 PM.
Reply With Quote
Old Apr 19, 2014, 06:06 PM
JuanRodriguez is offline
Find More Posts by JuanRodriguez
Registered User
The Villages, Florida
Joined May 2003
584 Posts
Quote:
Originally Posted by JimDrew View Post
New updater (updater45.exe) has been released! Includes new firmware for the Nano, Nano II, RFU, and X10+ to support long frame rates used by radios using PPM data with more than 12 channels.

Nano II also now uses the port based outputs instead of channel based outputs. This means that every output can be reversed and/or have an offset position from center.

Changes made for all updates is available on the downloads page, located here:

http://www.xtremepowersystems.net/xd...are%20Upgrades
Jim,

You're the best ! Nice work.....
JuanRodriguez is offline Find More Posts by JuanRodriguez
Reply With Quote
Old May 08, 2014, 01:06 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater46

New updater (updater46.exe) has been released! Includes new firmware for the Nano II, RFU, X10+, and JR transmitter modules (fix for Taranis). The firmware for the X10+ adds DMSS X-BUS support.

http://www.xtremepowersystems.net/xd...are%20Upgrades
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Old Jun 11, 2014, 03:56 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 48

A new version of the updater was released. This corrects a problem with SBUS2 mode with the X10+. Nothing else has changed.

http://www.xtremepowersystems.net/xdp/updater48.exe
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Old Jun 11, 2014, 09:22 PM
GBR2 is offline
Find More Posts by GBR2
Stress Be Gone
GBR2's Avatar
Snohomish, WA
Joined May 2000
3,423 Posts
Ran 4.8. Just to let you know it still says 4.7 at top of window.
GBR2 is offline Find More Posts by GBR2
Reply With Quote
Old Jun 12, 2014, 12:47 AM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Ok, I will look into that. It shouldn't!
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Old Jul 20, 2014, 09:02 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 49

This updater is a complete re-write for the Taranis' XJT mode support using our JR module. No other changes were made for other products.

http://www.xtremepowersystems.net/xdp/updater49.exe
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Last edited by JimDrew; Mar 03, 2015 at 02:50 PM. Reason: fixed link
Reply With Quote
Old Mar 03, 2015, 02:50 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 50

This updater adds support for Graupner's SUMD protocol with the X10+ board.
No other changes were made for other products.

http://www.xtremepowersystems.net/xdp/updater50.exe
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Old Mar 11, 2015, 05:32 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 51

Updater removed - do not use.
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Last edited by JimDrew; Mar 14, 2015 at 07:53 PM.
Reply With Quote
Old Mar 12, 2015, 12:00 PM
Liberty10 is online now
Find More Posts by Liberty10
Yin & Yang
Liberty10's Avatar
United States, VA, Sterling
Joined Jul 2011
5,183 Posts
sub'd
Liberty10 is online now Find More Posts by Liberty10
Reply With Quote
Old Mar 14, 2015, 07:54 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 52

This updater fixes the binding mode support for DSM2/DSMX binding with the X10+ board.

http://www.xtremepowersystems.net/xdp/updater52.exe
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote
Old Mar 30, 2015, 07:43 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Lake Havasu, AZ
Joined Jun 2005
16,528 Posts
Updater 53

This updater adds support for XBUS Mode A's failsafe packets. You can now change the failsafe settings from the transmitter and have them apply to the X10+ board.

http://www.xtremepowersystems.net/xdp/updater53.exe
JimDrew is offline Find More Posts by JimDrew
RCG Plus Member
Reply With Quote


Thread Tools