HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Feb 16, 2013, 01:35 PM
Registered User
Joined Jul 2012
17 Posts
I'm using the atmega 8 , the circuit diagram will not work for the atmega8 , you need to download the pin diagram for the atmega8 and install the xl and power ....risitors. ...and then it will work the schematic is for the 48 and the atmega8 pins do not match.

and the analog circuit works just fine too maybe not as good as microcontroller. need to take off a few parts and it's 1 work for 2 batteries not 3 and it works fine with 2s batteries
electrontube is offline Find More Posts by electrontube
Last edited by electrontube; Feb 25, 2013 at 11:20 AM.
Reply With Quote
Sign up now
to remove ads between posts
Old Mar 08, 2013, 08:34 PM
Registered User
Joined Oct 2012
224 Posts
hey Bruce abbot

I did successfully with atmega8 smd ( use crytal resonator )

I see ,LED on, when plug in output mtor brushed, LED off ,and when convert signal LED On ( version 0.6 )

Is it work that way?

pusle sinal is 1.1ms and 1.9ms ? why 50% joystick of tranmiter is motor start run , 100% jostick motor run 80% speed ?

I use esc brushless tunygy 30a .( I convert brushed to brushless for helicopter my f45 )

thank a lot
fantasy1988 is offline Find More Posts by fantasy1988
Reply With Quote
Old Mar 09, 2013, 12:39 AM
We want... Information!
Bruce Abbott's Avatar
Hastings, New Zealand
Joined Jan 2001
5,188 Posts
Quote:
Originally Posted by fantasy1988 View Post
I see ,LED on, when plug in output mtor brushed, LED off ,and when convert signal LED On ( version 0.6 )
The LED will be fully on when the PWM input is at zero volts. When the motor PWM is connected the LED will vary in brightness depending on the PWM ratio (0% PWM = off, 100% = full brightness).

Quote:
why 50% joystick of tranmiter is motor start run , 100% jostick motor run 80% speed ?
Perhaps the PWM signal is distorted and not being properly measured. Measure the PWM input voltage with a multimeter and record the values for different stick positions. What voltages do you get at:-

Low throttle?
50% stick?
100% stick?
Bruce Abbott is offline Find More Posts by Bruce Abbott
Reply With Quote
Old Mar 10, 2013, 09:18 AM
Registered User
Joined Oct 2012
224 Posts
thanks BRUCE

led on/off by PWM signal

I am set up esc min THR and max THR , it is work well

I will make two circuit for my helicopter f45
fantasy1988 is offline Find More Posts by fantasy1988
Reply With Quote
Old Apr 18, 2013, 02:56 AM
Registered User
Hasi's Avatar
Austria, Stmk., Graz
Joined Sep 2011
450 Posts
Hy Bruce!

Could you please also make a FW for the Atmega8 using the internal oscillator (8MHz)? It would be really helpful...

edit. I don't need it anymore, as it is possible to flash the escs.
Hasi is online now Find More Posts by Hasi
Last edited by Hasi; Apr 18, 2013 at 03:22 AM.
Reply With Quote
Old Apr 18, 2013, 10:11 AM
Registered User
Joined Oct 2012
224 Posts
Quote:
Originally Posted by Hasi View Post
Hy Bruce!

Could you please also make a FW for the Atmega8 using the internal oscillator (8MHz)? It would be really helpful...

edit. I don't need it anymore, as it is possible to flash the escs.
You should use external fluctuations, its stability

I met a lot of cases errors chip oscillator because frequency deviations


if you still want use internal oscillator 8mhz , yo need Fuse bit for atmega before load program
fantasy1988 is offline Find More Posts by fantasy1988
Reply With Quote
Old Oct 25, 2013, 11:27 PM
Registered User
Joined Nov 2012
130 Posts
hello Bruce
I can increase speed the conversion ? software currently speeds slow ,so it is suitable for convert Motor main .
But motor taill is need speed quick
where is command line change speed convert in code ? I am not yet understand
rc my life is offline Find More Posts by rc my life
Reply With Quote
Old Oct 27, 2013, 08:25 AM
We want... Information!
Bruce Abbott's Avatar
Hastings, New Zealand
Joined Jan 2001
5,188 Posts
Quote:
Originally Posted by rc my life View Post
hello Bruce
I can increase speed the conversion ? software currently speeds slow ,so it is suitable for convert Motor main .
But motor taill is need speed quick
where is command line change speed convert in code ? I am not yet understand
To improve the response speed you can increase the servo output pulse frequency in the source code. Most ESC's can handle 200Hz.

Code:
.EQU	FRAMETIME = 10000-1 ; Servo pulse repetition period (40000=20mS) 
                            ; Reduce this value to increase frequency, 
			    ; eg. 10000 = 200Hz (OK for Hobbywing ESCs)
Bruce Abbott is offline Find More Posts by Bruce Abbott
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion circuit to go from brush to brushless motor electrontube Multirotor Talk 2 Jan 25, 2013 05:43 PM
Discussion Is this the only ESC compatible with Brushless and brushed motors? Bigbond Electric Power Cars 7 Jan 23, 2013 01:54 PM
New Product Unique Walkera V400D02 / V370D05 and RX2614V Brushed to Brushless Motor Converter BlueHorizons Product Announcements 1 Nov 18, 2012 11:02 AM
Help! Converting from Brushed to Brushless Motor shah Electric Plane Talk 19 May 04, 2009 11:50 PM
can astro gearboxes be converted for brushless motors Joel K. Scholz Power Systems 5 Mar 19, 2005 01:51 PM