 |
 |
|
 |
 |
 |
Dec 16, 2012, 11:09 PM
|
|
Australia, VIC, Delacombe
Joined Oct 2006
877 Posts
|
No I understand them I was only going to get a 10c Li-Po and load test it against the standard Li-Lion to see if I get the same result, not change to 10c to fly with.
|
|
|
|
|
|
Dec 17, 2012, 01:52 AM
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:32 PM.
|
|
Dec 17, 2012, 06:11 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
9116 PCB Move
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:32 PM.
|
|
Dec 17, 2012, 07:27 PM
|
|
|
Australia, VIC, Delacombe
Joined Oct 2006
877 Posts
|
nice job Steve, why do you keep going through PCB's
|
|
|
|
|
Dec 17, 2012, 08:02 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:32 PM.
|
|
Dec 17, 2012, 08:26 PM
|
|
|
Australia, VIC, Delacombe
Joined Oct 2006
877 Posts
|
OK
 Now I can see why? I have only done 1 PCB and that was due to a faulty gyro that threw the heli FFF to the left and into a wall, which at first I thought was a servo issue so I got new ones but it was the gyro. Tried to re solder the gyro etc but it just kept doing it so I pulled out and old gyro from one of my old DH boards and it worked sort of ok but I knew that the gyro I had used had another problem so I replaced the PCB. |
|
|
|
|
Dec 17, 2012, 08:52 PM
|
||
United States, TX, Austin
Joined Dec 2012
319 Posts
|
Quote:
 off!!! 
|
|
|
|
|
|
|
Dec 17, 2012, 09:17 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
Titanium Horse
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:33 PM.
|
|
Dec 17, 2012, 09:45 PM
|
|
Canada, BC
Joined Apr 2012
1,079 Posts
|
Been there done that! Unfortunately the main shaft is too long. You have to cut that pin so that it doesn't interfere with the main shaft. I used this until my replacements arrived. I wasn't able to achieve perfect level on the pins so mine wasn't as good as the plastic ones.
|
|
|
|
|
Dec 17, 2012, 10:09 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:33 PM.
|
|
Dec 17, 2012, 11:05 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
9116 PCB Move
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:33 PM.
|
|
Dec 18, 2012, 12:17 AM
|
|
|
Australia, VIC, Delacombe
Joined Oct 2006
877 Posts
|
How close to the motor are your motor wires cos from the pic they look like they run down the side of the motor, if they do I would pull them away from it so the motor doesn't melt the shielding.
And I don't think I would like to have that Li-Po so close the the heat of the motor? Also what Battery are you using? |
|
|
|
|
Dec 18, 2012, 12:30 AM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:34 PM.
|
|
Dec 18, 2012, 12:33 AM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
9116 PCB Move (Results and Performance)
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:34 PM.
|
|
Dec 19, 2012, 09:30 PM
|
|
|
United States, WI, Beloit
Joined Nov 2012
1,985 Posts
|
9116 PCB Move (Results and Performance)
Deleted
|
|
|
Last edited by Steve_; Apr 20, 2013 at 03:35 PM.
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Discussion New Double Horse 9116 RC Helicopter 4 Channel 2.4Ghz RTF with Gyro | thercguy | Electric Heli Talk | 4 | Apr 16, 2013 03:13 AM |
| Question Double horse 9116 Heli | capo58 | Beginner Training Area (Heli-Electric) | 3954 | Dec 26, 2012 07:40 AM |
| Discussion New to Heli's - Double Horse 9116 or 9118 | kamma1124 | Coaxial Helicopters | 19 | Sep 28, 2012 10:08 PM |
| Question Starting with a new Double Horse 9116 | Scotticism101 | Beginner Training Area (Heli-Electric) | 3 | May 15, 2012 01:36 PM |
| Discussion 9116 Double Horse | Daza1964 | Beginner Training Area (Heli-Electric) | 1 | Mar 26, 2012 09:22 AM |
|
|