|Jan 21, 2010, 06:28 PM|
Ok everyone I took two great epp planes and made
a few changes to them and made what I think is a
even better plane!
I call it the SLoYak28
the plane was designed around the slofly28 designed
by Sloper Steve& Gene bond
to build this kit you need to download the 2 sets of plans
below "they are free of course"
print and tape together the 2 fuselage parts of both planes
and the tail section of the Yak55 (just the rudder piece)
also tape together the wings and the elevator pieces from the
slofly28 set of plans.
I used standard 8 1/2 x 11 typing paper.
(tip if you printer will take card stock use it as it makes
a better template)
Stay tuned a video will show you the basics of how I merge
the two plans to build one.
Parts used on plane kit
1 sheet 18 x 36 1.3# 9mm epp foam
2. 3mm x 1000mm carbon rods or tubes
1. blue wonder 1300kv outrunner From Hobby King.
1. 3mm prop saver
1. epp motor mount
1. 10 amp esc
3. blue bird 306 micro servos
1. gws 4 channel rec
1. gws 9050 prop
1. 7.4 volt 300-500 mah (20C) lipo (remember ligher is better) 250-350mah is what I like.
1. dubro Mini E/Z Connectors #845
2. dubro Micro Control Horn- Narrow #848
1. dubro Micro E/Z Link #849
1. dubro 30” Micro Pushrod System #852
1. 1/32 sheet of lite ply (used for control horn stiffners)
1. 5 minute epoxy
1. hot glue gun with low temp sticks
1. roll strapping tape (staples) the kind with fiberglass strings in it.
1. x-acto knife # 11 blades
1. medal straight edge ruler 18" or longer works best.
1. set wire cuters
1. 1. small screw driver set
Dremel with cutting tool or Soldering iron to cut groves in foam for carbon.
use what methods works best for you.
|Jan 22, 2010, 12:58 AM|
Here is The sloyak32 "Final Version"
This plane was created using google Sketchup I went with a larger wing 32" as i wanted a ligger larger wing area, I also moved the Elevator forward a little.
The Sloyak32 video
The plane in the video is using this setup.
Bluewonder 1300kv motor
GWS 9050 prop
2 cell 7.4volt 360-500mah lipo (20-25C) discharge
3 towerpro 5 gram servos
1 gws 4 channel rec
All dubro connectors and ez-connectors
10amp budget esc (brushless)
3.0 mm carbon for wing and fuselage + elevator
1.3# 9mm epp foam for plane
Hot glue for hinges
Hot glue for build
Strapping tape to hold servos and stuff in place
AUW with 2 cell pack Just 6.5oz
Download the Complete plane Plans below.
|Jan 22, 2010, 01:14 AM|
|Jan 23, 2010, 10:55 PM|
What I want to know Rob, is how you get everyone to move their cars out of the parking lot when you maiden and fly your planes
|Feb 03, 2010, 02:37 PM|
New Video From last weekend
I have not flown this plane in Awhile so I thought I would shoot a new video of me cranking it through a few flights.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|For Sale||Kontronik Fun 600-18, 4.2:1, and Jazz 55 10 32 used||davecee||Aircraft - Electric - Power Systems (FS/W)||4||Mar 24, 2010 06:14 PM|
|Discussion||strippers . . . and crimpers for 32 AWG||Kookaburra||DIY Electronics||8||Jan 12, 2010 05:16 PM|
|Sold||Du-Bro Sheet Metal Screws NIB 32 screws for $3.00 shipped||jodini||Aircraft - General - Miscellaneous (FS/W)||2||Jan 11, 2010 01:43 PM|
|Discussion||Plans needed for Eflite Power 32||Daddy-O||Foamies (Scratchbuilt)||7||Jan 10, 2010 01:41 AM|