|Mar 09, 2013, 08:43 AM|
And here is a weight report of the structures.
Rudder - 1.1 g
Fin - 0.7 g
H Stab - 2.1 g
Elevator - 2.9 g
Wing & Hatch - 24.5 g
Fuselage - 39.0 g
This totals to... 70.3 g (or 2 and a half-ish ounces).
The flying weight of my E-Flite Carbon Cub is 90 g. I still might be able to use a Park 180 size motor.
|Mar 13, 2013, 12:28 AM|
Tonight, I installed the receiver, 2 x servos (5g because I had them), a 10A ESC, a Park 180 2200Kv motor, and a 6030 prop. The front of the plane is quite large and masks some of the prop. I may have to make a streamlined nose piece, while I was hoping to make it look like a flat radiator, like the SE-5a.
The fuselage weight increased to 91.5 g... total now at 123.8 g.
A 2S 300 mAh battery runs about 15g... 140g
The carbon cub weighs in at 90g, so I probably need to up the motor and, perhaps, the ESC.
|Mar 13, 2013, 01:45 AM|
Joined May 2002
My, that is a good bit of weight for that motor to haul around, based on the numbers I've seen for it. Perhaps a Park250 would better serve your purposes? Just a thought... But it looks very good, I must say!
|Mar 13, 2013, 06:46 PM|
Thanks for the kind words... I wasn't thinking. When I thought about my Carbon Cub's 90 g, I knew better. I've ordered a Power Up 250 plus from HeadsUp RC that should do nicely. I had larger motors but no one in the 250-300 range.
My spreadsheet tells me that for:
-- 40 mph Vmax
-- 2S system
-- 200 g weight
-- 90 W/lb (so 40 Watt system)
-- 1400 Kv at 75% efficiency
-- 7 A Cmotor
--10 A ESC
That I can swing a 7x4 prop with 6 A on the motor. So I will put an 8040 on it and bench test it in case the efficiency is better. At 80% efficiency the 8040 prop should give 20% more power at 7 A. At lower efficiency the current goes up.
|Mar 19, 2013, 08:19 PM|
I finally got the motor I was waiting on. But, I don't have a prop adapter for a 2 mm shaft; and, the prop keeper I have won't hold the thrust I'm generating... fratzen ratzen, stinken winken...
|Mar 21, 2013, 03:08 PM|
I just got the motor rigged up with an EP 8040 and the 2S system draws 5 A and produces 35.5 Watts at WOT. Let me see if I have a 9040!
Edit: I put a 9047 on the motor and it puts out 44 Watts at 6.5 A... I need to adjust the math in my spreadsheet. Now to do some more covering...
|Mar 21, 2013, 07:28 PM|
Finished the basic covering...
To do list:
-- Wing struts and attachment fittings
-- Wing-fuselage attachment fittings
-- Pilot, which is also the after wing-fuselage attachment latch
-- Nose block
-- Vent in the electronics bay for cooling air exhaust
-- Landing gear
-- Control horns
-- Exhaust pipe
|Mar 22, 2013, 10:04 PM|
I built the wing-fuselage attach mechanism.
Weight so far is 180.4 grams.
Remaining weight will consist of:
-- landing gear
-- wing struts
-- nose block
-- control horns
|Mar 22, 2013, 10:07 PM|
|Mar 22, 2013, 10:52 PM|
The covering looks good David! You are getting close to your maiden, very fast build! This plane looks like it should be a gentle flyer.
|Thread||Thread Starter||Forum||Replies||Last Post|
|Build Log BBCC-1 Blackburn Skua, #20 Free Flight to RC Flight Kitbash Contest, davidterrell80||davidterrell80||Balsa Builders||127||May 23, 2013 11:07 AM|
|Sold 2 JR DS 188 Digital High Speed Servos MOC $40||gva1956||Aircraft - General - Radio Equipment (FS/W)||2||Feb 11, 2013 12:00 AM|
|Rave White Knight / Space Ship One||foamflyer||Foamies (Kits)||10||Aug 03, 2005 08:59 AM|
|Rave Scaled Composites White Knight / Space Ship One||foamflyer||Scale Electric Planes||4||Jun 04, 2004 01:44 AM|