|Apr 30, 2010, 05:12 AM|
GWS Receiver ch 48 two different frequencies???
OK I know GWS receivers are crap...
Having said that I have had a 6 channel pico Fm 72 mhz ch 48 in my shock flier for 5 years without a glitch. I recently bought a similar kit and cheaped out and bought another GWS. This time it is a 4 ch pico 72 mhz ch 48.
It's rock solid until I move a control service, then the whole planes shakes like it is cold...
Here's the wierd part.
#1. The new receiver with my old CC 10 brushless controller plugged into it from my shockflyer arms normally and the motor runs normally. When I plug in the 8amp Great Planes brushless controller than came with the Rimfire 250 reccomended for the new kit, the motor won't arm and doesn't run. I put in the old 6 channel GWS receiver and it arms and works normally. WTheF??
#2. The channel listed on my old receiver's crystal is 72 MHZ CH 48 73.205. The new receiver with a GWS crystal ordered with it 72 MHZ CH 48 72.750. Why are the numbers different?
Shouldn't they be the same number?
|Apr 30, 2010, 07:12 AM|
73.205 minus 72.750 = .455
That's what's called the intermediate frequency (IF) of the receiver. The receiver crystal is always different from the frequency being received -- it's the difference that the receiver processes.
Some crystals show the actual frequency of the crystal, some show the frequency of the channel. Just look at the channel number and stop worrying about this point. It has nothing to do with any problems you might be having.
Do the problems you report go away if you move the transmitter farther away from the receiver? As I recall the GWS receiver may be subject to swamping.
|Apr 30, 2010, 02:05 PM|
It appears that at some point during the recent testing my transmitter died.
No matter what I switched around on either plane I couldn"t get any servo response or get the esc to arm.
I decided to throw a battery in my extra to double check the radio and sure enough I have the exact same problem with that model.
Do the Spectra modules on Hitec Eclipse 7's burn out, or did the radio die?
Worth ordering a standard ch 48 module to check the radio?
I have had it for probably 10 years and I fly alot, but treat it very well and keep it in a hard case....
|Apr 30, 2010, 07:42 PM|
Joined Aug 2002
Then re-check the arrows are actually pointing to 4 & 8 in correct order.. Just reseating pots may resolve problem.
(Have seen Spectra "problems" where operator had reversed the channel numbers.)
If TX battery is good withTX antenna scewed down firm and a problem still exists after above, suggest contact Hitec service information direct.
Alan's Hobby, Model & RC FAQ Web Links
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Idea||DX7 binding a receiver to two different transmitters||jib||Radios||9||Apr 23, 2010 10:29 AM|
|Sold||GWS R-6N II/H Receiver Ch 36||Gleber||Aircraft - General - Radio Equipment (FS/W)||2||Apr 07, 2010 10:24 AM|
|Sold||gws naro 6 ch FM parkflier receiver for futaba ch 40 includes crystal||grfcon||Aircraft - General - Radio Equipment (FS/W)||3||Feb 23, 2010 12:34 AM|
|Sold||GWS GWR-4P RX ch 30 two for $20||Greg Gimlick||Aircraft - General - Radio Equipment (FS/W)||0||Nov 01, 2009 10:12 AM|
|Wanted||Wanted: JR Receiver Crystal CH 24 & 48||slopensoar||Aircraft - General - Radio Equipment (FS/W)||0||Aug 30, 2009 05:29 PM|