SMALL - Telemetry SMALL - Radio
Thread Tools
Old Jun 08, 2013, 02:29 PM
GallopingGhostlr is offline
Find More Posts by GallopingGhostlr
Vintage Aircraft Lover
GallopingGhostlr's Avatar
United States, NM, Clovis
Joined Jan 2013
712 Posts
Depends on your field's elevation above sea level, engine and fuel you are using. With the SureStart, I'd try all 3. You'lll find one that is optimal. With a Black Widow, there wasn't much difference between a 5-1/4x4 and a 6x3 at sea level, but at 6,500 feet (1981 m) elevation, the plane flew on the 6x3 but barely crawled along with the 5-1/4x4. This was on 25% nitro fuel.
GallopingGhostlr is offline Find More Posts by GallopingGhostlr
Reply With Quote
Sign up now
to remove ads between posts
Old Jun 08, 2013, 02:51 PM
colibriguitars is offline
Find More Posts by colibriguitars
Registered User
Joined Mar 2011
1,476 Posts
ok, well, im flying at 2600 mts over sea level, with 25% nitro...
colibriguitars is offline Find More Posts by colibriguitars
Reply With Quote
Old Jun 08, 2013, 04:35 PM
GallopingGhostlr is offline
Find More Posts by GallopingGhostlr
Vintage Aircraft Lover
GallopingGhostlr's Avatar
United States, NM, Clovis
Joined Jan 2013
712 Posts
I'd give it a shot with a 6x3 and a 6x4 and compare.
GallopingGhostlr is offline Find More Posts by GallopingGhostlr
Reply With Quote
Old Jun 08, 2013, 07:29 PM
Balsabird is online now
Find More Posts by Balsabird
Balsadustus Producerus
Escondido, CA USA
Joined Jan 2001
1,104 Posts
Not exactly sure which current Cox you're running, but when I was a kid flying single channel stuff it was normal procedure to disassemble the Bee tank and reposition the fuel pickup tube to the tank bottom. Engine is assembled at the factory with the idea it will be flown in a control line airplane, so the fuel pickup tube is on the right side of the tank (with the needle valve knob pointing up). If the tube is too short, any silicone or vinyl tube of correct size will work if you cut it a bit longer than the original. Angle cut the end of the new line so it won't get closed off if it contacts the tank inside wall. I would reinstall the little anti-kink spring inside the pickup tube so it won't kink on reassembly.

If, during removal of the old fuel pickup line you find it is stiff or hard from exposure to fuel, don't just pull harder--you might break off the nipple at the venturi. Either heat it up with a covering heat gun or carefully cut it off with an X-acto.

A Cox black 6x3 should do the job in a fine fashion. Or something close if another brand.

More flying reports, please
Balsabird is online now Find More Posts by Balsabird
Last edited by Balsabird; Jun 08, 2013 at 07:36 PM.
Reply With Quote
Old Jun 08, 2013, 08:46 PM
GallopingGhostlr is offline
Find More Posts by GallopingGhostlr
Vintage Aircraft Lover
GallopingGhostlr's Avatar
United States, NM, Clovis
Joined Jan 2013
712 Posts
colibriguitars is using a Cox .049 SureStart engine, which does not have an attached tank. What you express Balsabird is standard procedure for all Cox attached metal tank engines. In my rebuild, I'm going to a TT GP-07 with a 1 oz. external slant tank and throttle.
GallopingGhostlr is offline Find More Posts by GallopingGhostlr
Reply With Quote
Old Jun 09, 2013, 01:57 AM
colibriguitars is offline
Find More Posts by colibriguitars
Registered User
Joined Mar 2011
1,476 Posts
Hi Guys, another video, hope you enjoy!!
Q-Tee rc, with Cox ShureStart (4 min 8 sec)
colibriguitars is offline Find More Posts by colibriguitars
Reply With Quote
Old Jun 10, 2013, 12:02 AM
kpriddle is offline
Find More Posts by kpriddle
Slow 'n Steady...Grease 'r In
kpriddle's Avatar
Maine
Joined Oct 2008
1,288 Posts
Nice flight! You sure are confident with your landings, aren't you.

KP
kpriddle is offline Find More Posts by kpriddle
Reply With Quote
Old Jun 10, 2013, 09:34 AM
GallopingGhostlr is offline
Find More Posts by GallopingGhostlr
Vintage Aircraft Lover
GallopingGhostlr's Avatar
United States, NM, Clovis
Joined Jan 2013
712 Posts
Really nice flying there, colibriguitars, brings back memories.
GallopingGhostlr is offline Find More Posts by GallopingGhostlr
Reply With Quote


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Found Q TEE kit sst2000 Aircraft - Fuel - Airplanes (FS/W) 9 Mar 18, 2013 08:08 PM
Discussion Airtronics Q-tee, The Original Park Flyer Alard Parkflyers 36 Mar 14, 2013 02:37 PM
Discussion Airtronics S-Tee conversion from Q-Tee ? turbojoe Balsa Builders 5 Feb 27, 2013 02:48 AM
Mini Q-Tee Build Thread Matt Chester Scratchbuilt Indoor and Micro Models 42 Jan 01, 2005 10:17 PM
67% Q-Tee build thread Matt Chester Parkflyers 3 Dec 22, 2004 07:27 AM