Engine selection for a 3 meter twin boom plane
I am currently planning on scratch building a 3 meter wingspan, twin boom, twin rudder cargo plane.
The overall length will be about 2.17 meters, with the main fuse about 1.10.
Main fuse will have four wheels, and the 2 front wheels will be steerable.
Booms, together with the tail feathers shall be detachable just at the aft of the engine nacelles. I will use telescoping aluminum tubing for that section.
The plane will have twin engines, mounted on the wings.
Construction will be plywood, balsa, CF tubing, aluminum tubing, an aluminum skeleton for the wing center section + engine mounts and depron.
Rudders will be pull-pull on a single servo, elevator will be operated with a pushrod.
All servos will be in the main fuse for CG considerations.
The wing will be three pieces, center section will be permanently attached on the fuse, with outer sections (just outside the engine mounts - nacelles) mounted via CF tubing and plastic screws. (Wing center section will have a removable cover do do the joining)
Wing chord will be 46 Cm, tapering after the engine mounts, down to 34 Cm at the wingtips. Leading edge will be straight, all taper shall be at the trailing edge.
There will be ailerons and flaps.
The wing, elevator and rudder will be plywood sandwiched in foam, and the wing will be reinforced with CF tubing and spruce spars. I will use wing struts, as well.
Also, wing leading edge will be CF tubing, to minimize damage.
Do you guys see any problems with the idea please?
What sort of a target weight should I be aiming at?
Also, the big question is, I am planning on using 2 ASP .52 engines for this plane.
Do you think I will have enough to get it going?
(Or, should I resort to a JATO setup for take offs )
Thank you for your responses..
This plan is getting more and more complicated every day.
I just want to try things I have never done from scratch before on this one.
I am now designing a custom retract system where I will pull the wheel trucks on the fuselage straight in, and the wheel bulges will open, and close once the wheels are tucked in for a clean look.
I just did a quick inventory, and came up with 15 servos total. (Servos and retracts will have their respective dedicated batteries)
Airfoil will be the classic Clark Y, flat bottom, with about a 2 degree angle of attack.
Wings will have 2.5 degree dihedral, midwing setup.
Looks like I will need "more engine", after all.
How about going with four engines then?
Also, can I mix and match the engines? (2 inboard ASP .61 engines on the wings, and 2 ASP .51s further out.)
That SHOULD get the plane up in the air, but do I have to have all four engines identical?
You have a point about gas engines, but I live in Istanbul, Turkey.
Gas is about $10/gal over here..
Plus, I can get nitro engines form Hobbyking for about 50-70 bucks, gas engines are about a grand a piece.
Also, I am very much used to glow stuff, andI actually like them.
United States, OR, The Dalles
Joined Apr 2011
Super Tigre 3250 maybe, then?
Nothing wrong with glow, but here glow fuel can run $20 a gallon, where gas around $3, plus gas engines burn less.
If glow is cheaper there, or if you just prefer glow, go for it. I just think you need to be looking at bigger engines.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Sold||Graupner 3.3 Meter Grob G 103 Twin Astir Sailplane AS-IS||gva1956||Aircraft - Sailplanes (FS/W)||1||Oct 20, 2014 10:38 AM|
|Discussion||New twin boom pusher plane for $149||Canada Goose||Aerial Photography||7||Sep 09, 2014 03:59 PM|
|Discussion||Ideas/ ratios for a twin boom pusher plane||boaterguy||FPV Aircraft||0||May 27, 2014 02:16 PM|
|Discussion||Looking for twin boom pusher plane||Canada Goose||FPV Aircraft||4||Dec 30, 2013 06:44 PM|
|Discussion||big 3 meter twin boom pusher just crashed||red_gol||UAV - Unmanned Aerial Vehicles||20||Jul 03, 2007 12:01 AM|