Hi Riahut,

Thank you very much for you're help! I really apreciate that.

Yesterday I tried everything I could but I dont get the " sand-icon" Also, I can't enter the menu. If I press Reset the screens gets black, just as lang I kee pressure at the button.

I only get " pigeon OSD V2". Also de led doesn't get green (or flashing). It just don't do anything.

Help..I really want to fly FPV with my wooden thermal FPV glider with L1D vario. Damnit

Ps, how is the service from justgorc? Anyone have experience with it?

I have what's maybe a stupid question. When I get my OSD all wired in, if I leave the OSD board unpowered(no 12v in), will the video still work, or does the OSD NEED to be turned on for the rest of the system to work?

Originally Posted by Bugman Jeff

I have what's maybe a stupid question. When I get my OSD all wired in, if I leave the OSD board unpowered(no 12v in), will the video still work, or does the OSD NEED to be turned on for the rest of the system to work?

Signal passes through the OSD so it has to be powered on, plus OSD powers camera as well.

Thanks for the confirmation. My system uses a 5v camera powered from the Vtx, so the video signal is the only wire passing through the OSD.

New version Suppo "Piegon" OSD v2.3 avaible on www.bambucopter.com

• Selectable Unit mode for meter/KM or feet/mile added
• Molex connector on GPS module

Manual





540 TVL Sony CCD Camera

just a minor update on the issues I have had with the Suppo. Turns out when I tested it, the OSD stays visible in the goggles for the whole flight ... but the recording on the FPVJapan DVR does not always show the OSD. It sometimes disappears from the DVR recording for maybe a minute or two. Really strange to me, though less of an issue than I thought.

Originally Posted by Widelec

New version Suppo "Piegon" OSD v2.3 avaible on www.bambucopter.com

Is there a way to flash the V2 with the V2.3 firmware? Being English/metric selectable without having to buy a whole new unit would be nice.

Originally Posted by Bugman Jeff

Is there a way to flash the V2 with the V2.3 firmware? Being English/metric selectable without having to buy a whole new unit would be nice.

I had asked to manufacturer " is the firmware update possible for v2.0 owners"
And answer is " Sorry , we do not provide firmware"


would be nice, if opensource or upgradable.

Originally Posted by Widelec

New version Suppo "Piegon" OSD v2.3 avaible on www.bambucopter.com[LIST][*]Selectable Unit mode for meter/KM or feet/mile added [*]Molex connector on GPS module

seems the only option in checkout is for V2, how do I purchase V2.3 ?

Originally Posted by greedyg76

seems the only option in checkout is for V2, how do I purchase V2.3 ?

sending v2.3 for all orders.
only v2.3 in stock now.

Originally Posted by Widelec

sending v2.3 for all orders.
only v2.3 in stock now.

thanks, just placed my order

Originally Posted by greedyg76

thanks, just placed my order

will be shipped morning.

I'm pretty sure, but want to verify, is the V2.3 a direct plug for plug swap for the V2, or is some rewiring needed?

Originally Posted by BCSaltchucker

just a minor update on the issues I have had with the Suppo. Turns out when I tested it, the OSD stays visible in the goggles for the whole flight ... but the recording on the FPVJapan DVR does not always show the OSD. It sometimes disappears from the DVR recording for maybe a minute or two. Really strange to me, though less of an issue than I thought.

I finally have a DVR that records through static, and Aiptek Mpvr +CB. My OSD behaves just as you describe. It's always visible in the goggles(FS Predators in my case), but the OSD overlay flickers in and out on the recording. It stays on or off for minutes at a time, it seems like it switches when I hit static in my downlink reception. I suspect, based on no evidence, that it has something to do with the refresh rate of the OSD. Any other suggestions as to what could cause this?