New Products Flash Sale
Thread Tools
Old Jun 27, 2012, 02:59 PM
hog2soar is offline
Find More Posts by hog2soar
Registered User
hog2soar's Avatar
Central California
Joined Jan 2010
1,140 Posts
Maiden flight of my semi scratch built Sig Riser 100

I finally got around to flying my Sig Riser 100 that I call "Mulligan" seeing how I used a golf shaft for the Boom.

What a great flying plane. It's going to make a great ALES Bird.

After building my Oly III last winter,I needed to have another project. So I bought a Sig Riser 100 kit,but decided to do my own modifications.

After building the wing,I decided to change the tips and make it a little sleeker looking. So I added 6" to each wing tip and added a little flair to them. Then I decided I didn't like the looks of the fuselage,and I thought the tail moment was a little to short. So I went out in the garage and got one of my old Golf shafts and decided to make a Pod and boom type fuseelage for it. I decided to design the pod after the Bubble Dancer. So I drew up a plan based on the Bubble Dancer Pod and built a balsa Pod,then fiberglassed it. I then determind the length of boom I wanted so I removed the grip and cut the head off the shaft. Then I epoxied it to the Pod.

Next I designed and built the tail feathers.I added a little flair to them also.

Now it was time to install the servos and linkage for the rudder and elevator. I was going to run the linkage inside the boom, with the servos inside the pod,but figured I would probably screw that up. So I cut a notch inside the boom under the horizontal stabilizer and installed a Dymond D60 servo in the notch for the elevator,and installed another D60 in the base of the Vertical stabilizer for the rudder. That way the linkage was only a couple inches for each. The wires run down the middle of the boom to the Rx.

Next I made firewall out of plywood and glassed it.

For power I used a Hyperion 2218-12 motor with a 13x6.5 Aeronaut prop. It has plenty of power to make 200 meters in less than 30 seconds. I needed to add a ounce and half of weight to get it to ballance. I may remove a ouarter of an ounce. It's all up weight is 60 ounces using a 3S 2200 Lipo.

I covered the wing in Ultracote Orange and Purple. It really shows up in the sky.

I really wasn't sure how it was going to fly,with all the changes I made. But I couldn't be happier it's one sweet flying plane. My first hand throw it went straight as an arrow and about 100 yards,hands free landing. So I powered it up,added a couple clicks of trim,and had one great day flying. It signals thermals very well and just want's to float.

I really did not expect this plane to be as good as it is. I LOVE IT.

hog2soar is offline Find More Posts by hog2soar
Reply With Quote
Sign up now
to remove ads between posts
Old Jun 27, 2012, 08:07 PM
whitefox545 is offline
Find More Posts by whitefox545
Registered User
whitefox545's Avatar
United States, PA, Canonsburg
Joined Apr 2011
53 Posts
Very Nice Job Mr. Hog !!! It's always nice when a plan comes together and even better when it woorks as well as it looks!! Cool colors also!! Anyone can build it stock but it takes a real Man to cut one up and make it work better!! Jeff L.
whitefox545 is offline Find More Posts by whitefox545
Reply With Quote
Old Jun 28, 2012, 12:58 AM
enyaws is offline
Find More Posts by enyaws
papa smith
enyaws's Avatar
United States, OR, Waldport
Joined Dec 2007
102 Posts
Very Nice Build Eddie: Most anybody can throw together a kit but you have some real imagination and a great looking plane. Glad it flies well for you. I think there is more skill than luck going on here. I can't quite place you from photo on your bio page, but hope to cross paths with you someday and learn a thing or two. Enjoy, Wayne
enyaws is offline Find More Posts by enyaws
Reply With Quote

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Video - Maiden and Second flight of my newly built Hexacopter chargenut Aerial Photography 15 Jul 15, 2012 06:51 PM
Video Volus 100 inch scratch built ourbluehorizon Sailplane Talk 0 Jun 11, 2012 12:48 PM
Build Log My new scratch built rc edf jet: the Falcon 70 (w/ build and maiden flight video) j3tman Scratchbuilt EDFs 13 Jun 22, 2011 10:19 AM