If you read the first post in this thread, KK mention being able to set it in 0.1v increments... Maybe I misunderstood...?

Originally Posted by LazyZero

There is only stated about acoustic signal when arm/disarm board.
Can't read anything about low bat alarm.

Christian

Read below in red color

Originally Posted by kapteinkuk

Hi all, I designed this one to be easy to use for the noobs, and still be better than the KK1.

The gadgets-freaks will not pitch a tent over this one, It is the same, tired old AVR-chip. (Sorry TC ) However, it runs on a 20MHz crystal, so output resolution and jitter is better than before.

Some improvements:

-No confusing potmeter directions.

-No gyro reversing needed since the FW is for a fixed HW setup.

-Self-leveling. It uses acc tilt-angle measurement. Later I will try to add a full AHRS algorithm like the big boys use since it is better. (less delay)

-No PC necessary. All adjustments and multicopter type selecting is done with the LCD and buttons.

-The transmitter setup can be checked before first test. (channels and direction)

-low drift gyros.

-graded low-voltage-alarm, adjustable in 0.1V increments.

-motor numbering and propeller direction is visible on the LCD.

-Custom mixer.


It will become open source when the first update is available. But beware, it is still written in Evil Assembly!!


Here is a buddycode, get it for $19:
http://www.hobbyking.com/buddy.asp?c...2-7C1628251969

Yes you are right. But where to attach?

The 2 pins for buzzer?I don't believe those 2 pins only for sound of arming/disarming the board.Somehow is a nonsense.

Does the aeroplane mode also include autolevelling? or is that only available for copters?

I put one of backorder. Wonder how long it'll take HK to restock... I know I won't hold my breath

Originally Posted by kapteinkuk

The gadgets-freaks will not pitch a tent over this one, It is the same, tired old AVR-chip. (Sorry TC ) However, it runs on a 20MHz crystal, so output resolution and jitter is better than before.

Hi, kapteinkuk! Good to see that it has a 20MHz crystal and an ESC calibration mode! I'd probably want to add CPPM input mode so that we can just buy a simple receiver and only connect the one signal wire. It needs reordering support for some radios, but it's not that difficult otherwise.

Are the lines drawn between the motors not quite perfect in the picture, or is that just bad image scaling?

me too. hope they have it asap

Here's another buddy code for those of you who what to get a discount on your back orders:

http://www.hobbyking.com/buddy.asp?c...8-CE1EDE08EF6F

This one is from my account and hasn't been used yet. Remember, you have to be logged in first before you click on the link. It drops the price to $18.54 US.

Cheers!

Anyone else have a buddy code? I can't seem to get the lower price.

Originally Posted by Hasher66

Here's another buddy code for those of you who what to get a discount on your back orders:

http://www.hobbyking.com/buddy.asp?c...8-CE1EDE08EF6F

This one is from my account and hasn't been used yet. Remember, you have to be logged in first before you click on the link. It drops the price to $18.54 US.

Cheers!

the buddy codes did not work ...
and they have now limited it to 1 unit PER SALE !!!
that mean if u want 2 units u will have to make 2 orders
more shipping revenue for them
great ... no working buddy codes & 1 unit per sale

Originally Posted by brettwal

Anyone else have a buddy code? I can't seem to get the lower price.

Sorry about that. Somebody must have already used it. I checked it to make sure it was working before I posted it. It appears to be dead now.

Appearently they removed the buddy codes for kk2.

ow, good for me. i was able to order with buddy code

They're going to make a lot of these boards and they will offer discount again. Let's just hope it works right :-)