OSD pro with guardian issue

sidewinderFSK · Jan 30, 2013, 04:02 PM

When I turn on the Stabilization / Elevn Mixing On the plane ailerons will deflect when the wings angle changes, only problem is turning to the LT is good. Turning to the RT the ailerons start to deflect in the correct direction until the wing dips approximately 10%,,, at this time the servos will move to full travel in the opposite direction. This would cause a uncontrollable decent straight to the ground.

Under the guardian menu I can not get heading hold to work.

The manuals are wonderful, but to extensive. On one page you need,
Connect this here,
place this there,
turn this on,
If it doesn’t work read here! (Ladder troubleshooting) not surf the forums. I have no doubt that someone had my RTH problem, but finding it.

And gee-whiz guys why didn’t you make room for heading hold / RTH activation via an aux channel or am I missing something. Navigation of your menus while flying sucks. If I was flying at 10000 ft no problem, but at 300 ft, only seconds to the ground? Or am I missing something. Create a serial device to control function using aux channels. Right now as far as I understand the OSD Pro, with the guardian has 2 AUX input to control the OSD extensive table of contents. Switching between these menus while flying takes hours of practice and removing the pilot’s attention from what matters, flying!

The OSD is functioning correctly, I have too much invested in the support equipment, (video) If I can't get some real tech support the eagletree is coming out and will find the FPV system that works as advertized!

billpa · Jan 30, 2013, 04:34 PM

Hi Sidewinder, & sorry you're having an issue with the stabilizer.

Let's first focus on getting that resolved, then I want to get more feedback from you about how we can improve the manual and the menuing.

Can you please follow the below steps. As a shortcut, you could first follow step 3, and if that doesn't work, also do steps 1 and 2. However, I suspect doing step 3 will resolve the issue.
1) If you are not running version 10.43 of our software already (indicated by clicking "Help, about" in the software), please install version 10.43 from here.
2) Open the OSD configuration page in the software, and click "Factory Reset," which will clear out your prior config. Then configure the OSD's display settings as desired, and click OK.
3) At this point, run the Servo Analysis Wizard either on the PC, or from the OSD's menu.
4) Confirm the problem is resolved.

Please let me know what you find.

Jan 30, 2013, 04:02 PM	#1
sidewinderFSK Registered User United States, TX, Lubbock Joined May 2007 37 Posts	OSD pro with guardian issue When I turn on the Stabilization / Elevn Mixing On the plane ailerons will deflect when the wings angle changes, only problem is turning to the LT is good. Turning to the RT the ailerons start to deflect in the correct direction until the wing dips approximately 10%,,, at this time the servos will move to full travel in the opposite direction. This would cause a uncontrollable decent straight to the ground. Under the guardian menu I can not get heading hold to work. The manuals are wonderful, but to extensive. On one page you need, Connect this here, place this there, turn this on, If it doesn’t work read here! (Ladder troubleshooting) not surf the forums. I have no doubt that someone had my RTH problem, but finding it. And gee-whiz guys why didn’t you make room for heading hold / RTH activation via an aux channel or am I missing something. Navigation of your menus while flying sucks. If I was flying at 10000 ft no problem, but at 300 ft, only seconds to the ground? Or am I missing something. Create a serial device to control function using aux channels. Right now as far as I understand the OSD Pro, with the guardian has 2 AUX input to control the OSD extensive table of contents. Switching between these menus while flying takes hours of practice and removing the pilot’s attention from what matters, flying! The OSD is functioning correctly, I have too much invested in the support equipment, (video) If I can't get some real tech support the eagletree is coming out and will find the FPV system that works as advertized!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cool Guardian stabilization module for your OSD Pro - $54.99!	billpa	Video Piloting (FPV/RPV)	1909	May 08, 2013 10:10 AM
Sold Eagle Tree OSD Pro with Guardian Stabilizer	Mattsrcking	FPV/RPV - Equipment and Vehicles (FS/W)	4	Oct 21, 2012 12:31 PM
Sold OSD Pro Pkg with V4 100A eLogger and GPS / Guardian (((SOLD)))	bah7566	FPV/RPV - Equipment and Vehicles (FS/W)	5	Aug 21, 2012 05:36 AM
Help! Problem with OSD Pro + Guardian	MatthiasC	Eagle Tree Systems	16	Aug 11, 2012 07:24 AM
Sold OSD Pro Pkg with 100A eLogger/Integrated Connectors and GPS and Guardian Stabilizer	Nick_P	FPV/RPV - Equipment and Vehicles (FS/W)	1	Jun 16, 2012 11:45 AM

RCG Sites

About RCG

Features

Tools

Media

Topics

Jan 30, 2013, 04:34 PM	#2
billpa Registered User Joined Nov 2003 4,787 Posts	Hi Sidewinder, & sorry you're having an issue with the stabilizer. Let's first focus on getting that resolved, then I want to get more feedback from you about how we can improve the manual and the menuing. Can you please follow the below steps. As a shortcut, you could first follow step 3, and if that doesn't work, also do steps 1 and 2. However, I suspect doing step 3 will resolve the issue. 1) If you are not running version 10.43 of our software already (indicated by clicking "Help, about" in the software), please install version 10.43 from here. 2) Open the OSD configuration page in the software, and click "Factory Reset," which will clear out your prior config. Then configure the OSD's display settings as desired, and click OK. 3) At this point, run the Servo Analysis Wizard either on the PC, or from the OSD's menu. 4) Confirm the problem is resolved. Please let me know what you find.