|Feb 17, 2011, 12:26 AM|
Joined Jun 2003
New Ritewing Roket motors
Hey guys I am bringing these back with some mods,they are billet pollished for better heat transfer.
The shafts have ben modified to 4 mm on the 28 40 series and the 28 56 series.
And the 12 mm motors have a new larger 2 mm shaft
Here is a pic of a 12 mm 4000 kv, 28 32 1900 kv, 28 40 2500kv ,an 28 56 1900 and a 36 50 880 kv
Here are the spex on the whole line of motors,I will mostly be carying the 28 series but I can get any of them orderd if you need one that I dont have.
I am building my stock now,it this market its a little rough,but if you want one of the best inrunners ever made then you are in the rite place.
Prices are subject to change, but here is the prelim numbers
28 /56/1900 kv with 4 mm shaft 95.00 $ good for Demon 6s and tl 50 or 48 lightning on 3s or 4s
props vary from 6/4 sport to7/5E
28/40/2500 kv 4 mm shaft 85.00 $ good for Demon on 4s or tl 50 on 4s or 36'' lightning 48 lightning on 3s and 4s
28/32 1900 kv 3.2 mm shaft 75.00 $ iyf on 7/5 apc slowfly ,or lite 36 lightning on afew diff props
12/30 4000 kv 2 mm shaft 50.00 $ small wings or micro pylon
12/30 5300 kv 2 mm shaft 50.00 $ same
|Feb 17, 2011, 02:28 AM|
That big honker is a 36-70-880, rite?? Not 36-50?
Love that polished surface. Should give good heat transfer to a heat sink and/or clamshell heatsink mount.
Sure is nice to have these motors back and available again. With some improvements, even!
I bet some 450 heli guys will jump all over the 28-32 series.
3400kv will be rippin' hot on strong 3S and hard 3D
2400kv for 4S and hard 3D.
|Feb 22, 2011, 07:54 PM|
Received 28/40/2500 today,,,,Looks VERY nice with that 4 mm shaft.
My Demon blunt is ready to go but unfortunately there's still a foot and a half of snow on the ground.
Landing a wing in that gets kinda messy.
Suggestion for a Rokett promotional image
|Feb 26, 2011, 06:43 PM|
The 28 56 1900 has a 4mm shaft and 16mm/19mm spacing on the mounting holes?
The shiny metal finish makes these the only ones even my wife would consider buying... Great!
|Mar 03, 2011, 09:27 AM|
I flew my new Rokett 26-56-1900 this past weekend.
My KV testing of the motor showed
2172kv on 3S and
2143kv on 6S.
(important to note that the Medusa motors were spec'd with a loaded KV, not unloaded like most mfg. When ordering, plan on 10%-20% higher true KV than spec'd unless CK says the specs have been changed to match true KV.)
6S 4000mah 45-90C
APC 6x4 Sport prop
CC ICE 100 ESC
In-flight in a level pass got:
That puts the motor at 83% of loaded KV. Outside temp was 80F and I was burning around with quite a bit of WOT. Motor came down about 100F so I feel comfortable saying the 1900 is a good 6S setup on the 6x4 prop.
|Mar 14, 2011, 12:35 AM|
Joined Jun 2003
I placed an order for 90 motors last week, they are plnned to be here for seff,
I told hance today that he needed the 12 mm for the micro fly he was flying today.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Sold||New: RiteWing SPORTSTER 30" Wing + Lamifilm = 35$ Shipped or trade for micro gear||samolot||Aircraft - Electric - Airplanes (FS/W)||23||Jan 12, 2011 12:35 PM|
|Sold||1 NEW and 1 like new Alfa Fan Units w/Motors and High Performance Rotors||Kevin Greene||Aircraft - Electric - Jets (FS/W)||2||Sep 24, 2010 12:52 PM|
|Sold||Ritewing TL50 Kit - New in Box - $70||PlusRC||Aircraft - Electric - Airplanes (FS/W)||1||Sep 14, 2010 12:34 AM|
|For Sale||NEW AND LIKE NEW PZ BRUSHLESS Charger, ESC, Motors!!!||Kevin Greene||Aircraft - Electric - Power Systems (FS/W)||0||Sep 12, 2010 06:41 AM|
|Sold||RiteWing Demon Lite 40 built by Chris Klick wil also trade for a fast rc speed boat||mechengineer03||Aircraft - Electric - Airplanes (FS/W)||3||Sep 09, 2010 06:55 PM|