|Jul 21, 2007, 09:55 AM|
USA, KS, Wichita
Joined Sep 2002
Arming Switch Question
I am just getting started in electrics and I have a question about how people are doing their arming switches. Having flown gliders for my entire time I have flown RC I get a little nervous around the business end of these electrics. Not sure if the power system makes a difference on how you do the arming switch so I will describe the two systems I am currently using.
Motor: Neu 1105-2.5Y/4.41
Controller: Phoenix 35
Battery: TP2100 3S Prolite
Motor: Neu 1112-1.5D
Controller: Phoenix 80
Battery: TP3300 3S
Any help you guys can give will be greatly appreciated.
|Jul 21, 2007, 04:53 PM|
Letchworth, Great Britain (UK)
Joined Jul 2004
I've only got an arming switch on one of my models, and that's because access to the battery connection is too close to the prop for comfort. I put a 4mm gold connector into one of the power leads, with the female half glued into, and poking through, the fuselage side, and the wire with the male part on poking through the side too. To energise, I just plug the male into the socket.
On all my other models my battery connectors (Deans Ultra) are my arming switch.
|Jul 21, 2007, 06:30 PM|
Joined Jul 2007
Re: Arming switch
If anyone can post a picture or 2 of the MPI Arming switch part # 6970 showing how you have it hooked up I sure would appreciate it. I'm new to EPower and thought the MPI would be a simple install I have been looking for pictures showing how it is hooked up I assume one set of the switch goes to the power leads and the other to the ESC wires?
|Jul 21, 2007, 06:53 PM|
Try not to post the same subject in two forum, hard to keep track what is going on.....
Brian, an EAJ
|Jul 21, 2007, 08:02 PM|
What is the wire loop with the spade connectors for?
Does it replace the fuse for measuring current with a clamp on type of meter?
What about the thing inset on the top right of both pictures?
|Jul 21, 2007, 09:16 PM|
That charging connector can handle the high current of charging? 3-4 amp?
Problem may be over charging the battery, voltage drop cross the connector may fool the charger to sensor a lower voltage than the pack is actually at, thus over charged the pack. Specailly bad for lipo. Not so for nicad and Nimh, they only sense the voltage peak regardless of the voltage.
Pat MacKenzie, The wire loop replaces the fuse in the system to check the current draw with a clamp meter.
Brian, an EAJ
|Jul 22, 2007, 08:08 AM|
Iíve used 35amps fuse to 30 & 40 to 35; for nearer 40 I made the shorting plug Ė only use it now.
The loop of 14ga wire is a shunt; lets me measure installed current w/o breaking into the wiring via multimetter -- precise .01ohm resistor, each .01 volt = 1amp.
With voltmeter plugged into the charging jack you can also get loaded volts; so then watts too!
Iíve had no problems pumping 6amps through the jack.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Question||Arming Switch Question||pmccleave||High Performance||50||Jul 29, 2007 09:57 PM|
|JR 8103 flap/throttle mixing with gear switch question||bfraser||Electric Sailplanes||0||Aug 30, 2002 07:50 PM|
|Can an arming switch on esc be bypassed?||omega blood||Power Systems||4||Feb 22, 2002 03:03 PM|
|Arming switch - charge jack||KatManDEW||Power Systems||4||Dec 03, 2001 07:09 PM|
|Can I put an arming switch in a signal wire?||Capt. Dave||Power Systems||3||Jul 03, 2001 05:15 PM|