 |
 |
 |
|
May 13, 2011, 12:12 PM
|
|
|
Durango Colorado
Joined Sep 2001
5,476 Posts
|
Nice photo, I see what you mean. Basically you have one of the ESC's + and - leads going into the Rx then ONE (like throttle) of your Rx to FC is a complete three pin connection, everything else is only a signal pin.
|
 |
Latest blog entry: FPV mQX
|
|
|
|
May 13, 2011, 12:21 PM
|
|
|
Clearwater, FLorida !
Joined Sep 2009
2,032 Posts
|
you got it.
picture of rx side. I use any open port to power the rx. Aux1 for the batt port is free for binding. ( you can bind with USB POWER ONLY , which is nice )  
|
|
|
Last edited by witespy; May 13, 2011 at 12:30 PM.
|
|
May 13, 2011, 01:45 PM
|
|
United States, WI, Milwaukee
Joined Jan 2011
791 Posts
|
If I wanted to use this board for a Y6 would I just add pins here? Or is it not possible...
What motors would connect in what order? (and of course modify the multiwii config and re-upload to the board) |
|
|
Last edited by Dolby; May 13, 2011 at 01:53 PM.
|
|
May 13, 2011, 01:58 PM
|
||
|
Durango Colorado
Joined Sep 2001
5,476 Posts
|
Quote:
|
|
|
|
Latest blog entry: FPV mQX
|
|
|
May 13, 2011, 06:46 PM
|
|
|
Hawaii
Joined Feb 2003
5,330 Posts
|
Paul,
Can the board handle a Y4 configuration? |
|
|
|
|
May 13, 2011, 07:31 PM
|
|
Boston, MA
Joined Jul 2010
924 Posts
|
My Quadrino arrived late this afternoon, first chance I got I swapped out the KK blue board on the VC-20 430mm Gaui frame, hooked the board up to the computer to verify settings, then out in the backyard to try it out.
Seems to have a severe case of the wobbles, if this were a KK or Gaui controller I'd just lower the gain setting(s) till it calmed down and go fly. Not so quick and easy apparently with the MultiWii variants, time for some PID tuning. I made a few small changes before it got dark and not in the right direction, looks like this is going to take a lot of trial and error to get it right. Can anyone give a quick rundown of which settings are the right ones to change to tame wobble and in which direction? |
|
|
|
|
May 13, 2011, 08:56 PM
|
|
|
South Carolina
Joined Mar 2009
3,806 Posts
|
RTRyder , Wanna sell your KK board?
|
|
|
|
May 13, 2011, 09:11 PM
|
|
|
Clearwater, FLorida !
Joined Sep 2009
2,032 Posts
|
Increase value for P until oscillations start, then back of slightly.
 on a VIC450 frame 3.2 is a good number to start with . lower the autolevel strength too |
|
|
|
|
May 13, 2011, 09:32 PM
|
|
|
Joined Dec 2009
1,510 Posts
|
you have a pm Paul
|
|
|
|
|
May 13, 2011, 10:20 PM
|
|
United States, TX, Midland
Joined Apr 2003
292 Posts
|
Come on Dad, let me fly!!!
|
|
|
|
|
May 13, 2011, 10:25 PM
|
|
|
South Carolina
Joined Mar 2009
3,806 Posts
|
Last year she flew my slow stick. she did pretty good. I think I will wait a few years before I let her fly the quad
|
|
|
|
|
May 13, 2011, 11:16 PM
|
||
|
Boston, MA
Joined Jul 2010
924 Posts
|
Quote:
I have a previous generation red board from Minsoo Kim I might part with though... |
|
|
|
|
|
|
May 13, 2011, 11:20 PM
|
||
|
Boston, MA
Joined Jul 2010
924 Posts
|
Quote:
|
|
|
|
|
|
|
May 13, 2011, 11:25 PM
|
|
|
South Carolina
Joined Mar 2009
3,806 Posts
|
RTRyder, PM sent.
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Help! need new flight controller recommendations | n3m1s1s | Multirotor Talk | 115 | Jan 09, 2012 09:38 AM |
| Article Subsonic's Motrolfly Plug and Play Power System: Motor, Controller & Battery Review | Michael Heer | Power Systems | 27 | Dec 16, 2010 12:36 PM |
| Data Plug 'n Play separates: An Esky CP2 with an E-flight 2 in 1... | elan | Micro Helis | 3 | Mar 19, 2010 08:51 AM |
| Discussion Air Hogs Plug n'Play Flight Deck Simulator | trust416 | Micro RTF | 14 | Aug 05, 2007 10:44 AM |
| Article Hangar 9's Piper J-3 Cub 40 Plug-N-Play PNP Plug N Play Evo 46NT Powered ARF Review | tailskid2 | Scale Fuel Planes | 6 | Dec 02, 2006 12:34 AM |
|
|