HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Aug 18, 2014, 09:04 AM
kha
openLRSng haxor
Finland, Espoo
Joined Mar 2011
2,008 Posts
Quote:
Originally Posted by obion View Post
Hi, trying to make TX woking as RX.
Flashed RX firmware without problems, can connect and configure module, too.
I'm getting problems to get out PPM output of it.
Enabled PPM output in configuration, then soldered a wire via 1k resistor to Port1 from atmega pin according schematics of 4ch/6ch receivers, attached it to the ppm configured arduplane autopilot and reaction to sticks is inadequate.
When I do full right with stick - then servo moves to its limits.
It moves only on full input, and nothing between center and full input.
Looks like it lacks something to work properly.
Any ideas?
I am afraid you need to do a bit more than load RX firmware on the TX.

firstly which TX unit you are hacking ?
kha is online now Find More Posts by kha
RCG Plus Member
Reply With Quote
Sign up now
to remove ads between posts
Old Aug 18, 2014, 09:16 AM
Registered User
Joined Jun 2013
13 Posts
Uhh, I thought that could be quite easy
Hawkeye 1W.
obion is offline Find More Posts by obion
Reply With Quote
Old Aug 20, 2014, 10:16 AM
Registered User
Joined Jun 2013
13 Posts
No ideas about making Hawkeye 1W JR TX working as RX?
obion is offline Find More Posts by obion
Reply With Quote
Old Nov 01, 2014, 09:55 PM
Registered User
juanej's Avatar
Joined Sep 2013
451 Posts
Can anyone tell me the differences between the DTF UHF DeluxeTX and the HawkEYE openLRS UHF?
juanej is online now Find More Posts by juanej
Reply With Quote
Old Nov 02, 2014, 06:34 AM
kha
openLRSng haxor
Finland, Espoo
Joined Mar 2011
2,008 Posts
Quote:
Originally Posted by juanej View Post
Can anyone tell me the differences between the DTF UHF DeluxeTX and the HawkEYE openLRS UHF?
You need to be a bit more specific as hawkeye makes dtfuhf versions too.

https://github.com/openLRSng/openLRS...-feature-table
kha is online now Find More Posts by kha
RCG Plus Member
Reply With Quote
Old Dec 02, 2014, 02:06 PM
Registered User
Joined May 2013
20 Posts
Hello,
I adapted a Futaba Hawkeye LRS 1W to a Hitec Aurora 9 but now, I want to know the firmware version of the TX and update it.. but I don't know how!? Please, do you have a manual to see the pinout? I have a 5V FTDI, and a USBasp ....

In this picture, you can see the pinout: http://www.fpvmodel.com/img/433-hawk...hz-HawkEYE.jpg
What is the function of the right 4 pins: GND, SDA, SCL, VCC ? Can I flash the module through this pins?

Here, my FTDI: http://gallery3.mikrokopter.de/var/a...g?m=1409747879

Regards.
flyergz is offline Find More Posts by flyergz
Last edited by flyergz; Dec 02, 2014 at 02:50 PM.
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion The Official Teen Chit Chat Thread Part 2 (Always Off Topic) Park_aviator Chit Chat 10225 Today 09:48 PM
Discussion 2013 NEAT Fair, the official start-up thread. Shinhopple, NY Sept 12-15th Tom Hunt NEAT Fair 2013 125 Sep 10, 2013 11:40 PM
Official LMR Sailplane Contest thread rcjunkie SEFF 2013 9 May 06, 2013 08:57 PM
Discussion Official Naza Thread-Post your issues AND solutions here FixedWing172 Multirotor Talk 1 Apr 23, 2013 05:40 PM