|Nov 12, 2004, 02:21 PM|
looking for suggestions
Ok guys I've read alot of post and I'm ready for my first helli.
I have a JR 652 tx.
a couple of gws pico 4 rcv.
some micro servos
ics 300 esc
I was thinking of going with the gws dragonfly em300 airframe and
the pg-03 gyro.
Will I need anything else to get started?
I also have a bunch of J250 motors I would like to find a use for so
something compatible with those would be nice.
Any better suggestions for a setup.
I've been reading so much I think I'm a little shellshocked.
Also I've been practicing with R.F. g2 off and on so I hope that will
|Dec 16, 2004, 01:54 PM|
Joined May 2003
does the jr tx do Revo mixing ? If so, how many points does it have. My JRx378 only has a 2 point revo curve which really sucks. you should have at least 3, ideally 5.
if you only have a 2 point curve, or no revo mixing at all, then you will need :
a feda/hummingbird mixer that will mix tail and main throttle and work with a pg03.
your j250 will be fine, but you'll need a tail motor like the gws edp50xc
you could get 2 escs (2 and 5 amp)
Heading Hold Gyro (futaba gy240)
and the motor/s
Using the second method is not only better, it means you don't have to worry about any mixing. The only catch is, the gy240 goes for about $100us
|Dec 16, 2004, 08:08 PM|
Thanks for the input guys but uh... I posted this back on 11/12. I currently have
Ozzie your right my 652 does have revo but only a 2 point curve best I can tell.
I've got it to hold the tail ok with the stock century gyro but couldn't figure out
why I could't get it trimmed. It always wants to lean and takes alot of throw to correct. After close inspection last night I noticed that one of the arms has borken on my swash. So I guess it's time for an upgrade.
Any suggestions on which one or from whom?
I can only guess what Coaxial was talking about??? lol
|Dec 16, 2004, 08:25 PM|
Dont waste money on an aluminum swash plate. Get a GWS swash plate and add a ball in swash mod. Dont know how you broke it, but they are not a commonly broken item, and the aluminum swashplates offer no improvement in control.
|Dec 16, 2004, 10:06 PM|
I don't think I broke anything actually. It looks looks like a link is missing
from the swash to the timing yoke. I don't have it here but I will check in the A.M.
I baught this used about a month ago and I am still trying to figure it out.
Thanks for the info on the alum. swash. I am going to order a ball in swash from
|Dec 17, 2004, 01:56 AM|
The swash from the 2004 GWS Dragonfly 300D is a ball-in swash. The part number is still FD008, so make sure you don't receive the old one (thanks Kellets!)
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Looking for suggestions||rcnutt||Foamies (Kits)||1||Apr 09, 2004 01:03 PM|
|Looking for suggestions on electric sailplanes||Jeff Skory||Electric Sailplanes||17||Sep 02, 2002 12:16 AM|
|still looking for suggestions||pval3||Parkflyers||1||Aug 23, 2002 10:00 PM|
|Looking for suggestions on motor/gear setup for Kyosho Stratus 1600||PDX Slope Pilot||Electric Sailplanes||3||Aug 21, 2002 09:50 PM|