Espritmodel.com Telemetry Radio
Reply
Thread Tools
Old Jun 24, 2013, 05:33 AM
Registered User
China, Guangxi, Guilin
Joined May 2013
35 Posts
Discussion
FY-PANDA II autopolit installation and debugging

hello , eveyone ,We are Guilin Feiyu-teh, thank you very much!
We will install PANDA II on the X8 airplane.
We share some pictures to everyone . you can refer to it install your PANDA II .
Then we send a video about panda II flight route.

1, bruless moter : power, Yinyan EMAX 925KV outer rotor brushless motor GT3520/05.

2, ECS: hobbywing, UBEC 60A,

3, paddle: propeller, 13*6.5 folding propeller;

4, servos: 17g-20g, 2.8KG-3.6KG GWS customization.

5 4S 14.8V 5200mah 15C, battery, lithium polymer battery


Name: 1.jpg
Views: 70
Size: 155.0 KB
Description:

Name: 2.jpg
Views: 102
Size: 153.3 KB
Description:

Name: 3.jpg
Views: 74
Size: 201.1 KB
Description:

Name: 4.jpg
Views: 84
Size: 116.9 KB
Description:

Name: 5.jpg
Views: 75
Size: 255.6 KB
Description:

Name: 图像183.jpg
Views: 83
Size: 151.0 KB
Description:

Name: 未命名2.jpg
Views: 105
Size: 101.6 KB
Description:
feiyu_tech is offline Find More Posts by feiyu_tech
Last edited by feiyu_tech; Jun 24, 2013 at 05:39 AM.
Reply With Quote
Sign up now
to remove ads between posts
Old Jun 29, 2013, 05:16 AM
Registered User
Joined Dec 2010
38 Posts
hello,guys, I send a video for everyone , it is fighting route about PANDAII.

PANDA II飞行轨迹 (5 min 56 sec)
hotfly163 is offline Find More Posts by hotfly163
Reply With Quote
Old Jul 04, 2013, 10:27 PM
Registered User
China, Guangxi, Guilin
Joined May 2013
35 Posts
hello ,everyone. Thank you very much for attention on our FEIYU TECH.
We share some pictures for you . Aircraft formation of X5.

Name: IMGSRC_20130705110326_54.jpg
Views: 48
Size: 144.8 KB
Description:

Name: IMGSRC_20130705110328_26.jpg
Views: 43
Size: 147.4 KB
Description:

Name: IMGSRC_20130705110329_69.jpg
Views: 41
Size: 152.6 KB
Description:

Name: IMGSRC_20130705110616_64.jpg
Views: 54
Size: 306.1 KB
Description:

Name: IMGSRC_20130705110552_4.jpg
Views: 40
Size: 310.3 KB
Description:

Name: IMGSRC_20130705110558_94.jpg
Views: 45
Size: 313.1 KB
Description:

Thank you very much!
We will take more efforts for everyone . We will make more comfortable produces for you.
feiyu_tech is offline Find More Posts by feiyu_tech
Reply With Quote
Old Jul 09, 2013, 01:46 AM
Registered User
China, Guangxi, Guilin
Joined May 2013
35 Posts
We share 5 videos, in this videos, we can see X8 airplane was controlled by FY-PANDA II. it was so stability and excellent.

X8 airplane was controled by FY-PANDA_II 1 (1 min 53 sec)


X8飞机由PANDA II 控制的飞行视频2 高清 (0 min 22 sec)


X8飞机由PANDA II 控制的飞行视频3 高清 (0 min 46 sec)


X8飞机由PANDA II控制的飞行视频 高清4 (1 min 6 sec)


X8飞机由PANDA II 控制的飞行视频5 高清 (0 min 24 sec)
feiyu_tech is offline Find More Posts by feiyu_tech
Last edited by feiyu_tech; Jul 09, 2013 at 03:30 AM.
Reply With Quote
Old Jul 24, 2013, 10:12 PM
Registered User
Joined Dec 2010
38 Posts
Turn control PID parameters adjust instruction
If autopilot fly under "NAVIGATION" mode, assume the flight from A to B, if occur the 4 phenomenon, please modify corresponding settings according to the instructions below, in order to get a better flying result.
(GCS 2D 4.0----“Param1”----“PID Control”---“Turn Ctrl”)
(1)In the 1st condition, the plane fly a long "S" way along the line, like the picture below, please modify the GCS4.0 settings "parameter1" -> "PID control" -> "turning control" the 1st and 3rd settings, increase the corresponding settings.
Name: 1.jpg
Views: 43
Size: 38.6 KB
Description:

(2) In the 2nd condition, the plane fly a small "S" way along the straight line, like the picture below shows ,please modify the GCS4.0 settings "parameter1" -> "PID control" -> "turning control" the 1st and 3rd settings, decrease the corresponding settings; if the issue still exist, please fine tune the 3rd item again, increase it at first, then tune it smaller if the "S" remained.

Name: 2.jpg
Views: 38
Size: 38.3 KB
Description:

(3) In the 3rd condition, the plane always deviate from the center of the line, please modify the FT-GCS4.0 settings "parameter1" -> "PID control" -> "turning control" the 2rd item, increase the corresponding data.

Name: 3.jpg
Views: 40
Size: 31.3 KB
Description:

(4) In the 4th condition, the plane wave along the line (with very small deviation to the center of the line), please modify the FT-GCS4.0 settings "parameter1" -> "PID control" -> "turning control" the 2rd item, decrease the corresponding data.

Name: 4.jpg
Views: 38
Size: 39.1 KB
Description:
hotfly163 is offline Find More Posts by hotfly163
Reply With Quote
Old Jul 14, 2014, 09:41 AM
RC Aircraft Noob Since 01-2012
Philippines, Davao Region, Davao City
Joined Dec 2011
90 Posts
Greetings! Where can I Get Mapmaker?

Greetings! I have recent;y purchased the FY Panda2 and am just setting it up. I would like to know where I can get the MAPMAKER software.

Please reply.

Thank you
magetpr is offline Find More Posts by magetpr
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion FY-Panda II saabguyspg UAV - Unmanned Aerial Vehicles 68 Jul 22, 2014 12:23 AM
Discussion FY-41AP autopilot & OSD installation and debugging feiyu_tech FPV Equipment 873 Jul 21, 2014 11:11 PM
Discussion FY-41AP autopolit & OSD for Multiaxis feiyu_tech Multirotor Talk 8 Jul 10, 2014 03:50 PM
Discussion FY Panda UAV system saabguyspg UAV - Unmanned Aerial Vehicles 63 Oct 22, 2013 01:15 AM
New Product FY thread: FY20A/FY21AP/FY3ZT/FY31AP/FY90Q/FY91Q/FY-Frame/FY-GCS/FY-OSD/FY-Dataradio yiny0730 FPV Talk 316 Sep 19, 2011 01:30 PM