New Products Flash Sale
Thread Tools
Old Jun 20, 2011, 10:48 AM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
I'd just like to make a few quick notes about the build as of the maiden flight.

Because I was worried about rolls being too sensitive I decided to install control horns only on the bottom ailerons even though I've hinged all four ailerons. The top ailerons are temporarily fixed in place by a few bits of 6mm foam and double sided tape.

I also installed a small fiberglass spar on the upper wing. I originally intended the design to be sparless because I had great success with other 24 inch sparless designs. But in the end I chickened out and installed a spar anyway.

The final hardware for the maiden are:

Battery: either 2S 370mAh or 2S 610mAh (swapping between the two didn't require much trim changes, just a couple of clicks on the elevator).
Motor: AX 1806N 2100kv 19g brushless.
ESC: Hobbyking 15-18A SS series.
Prop: 6x4.3

The CG is roughly towards the rear of the cabanes. I'll update the plans later to indicate CG directly in the template so you can mark it as you build.

The elevator is trimmed almost neutral with just a couple of clicks up. Of course, angle of incidence between the wings and horizontal stabilizer is zero.

Amazingly, with zero dihedral on both wings she flies perfectly fine with just rudder and elevator. I actually have my transmitter set up so that I can change from ailerons to RET at the flick of a switch and for the maiden I mostly fly her in RET mode.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Sign up now
to remove ads between posts
Old Jun 20, 2011, 11:05 AM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
I decided to add a few more finishing touches. I made a spinner out of a block of foam by tacking the block onto a small wooden dowel with hotglue and then attaching the whole thing to a drill to make a simple lathe. I then formed the foam using a metal file and a block of sandpaper.

I stole the idea of how to attach the spinner from another build thread (sorry, can't find it right now). I used a plastic tube that fits snug on the motor shaft to extend the shaft and then installed the spinner onto the tube.

I also made a pair of spats (wheel pants) for the wheels. It's built up from 3mm depron. if anyone's interested I can post the template for them.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Old Jun 20, 2011, 07:36 PM
soulreaper is offline
Find More Posts by soulreaper
Registered User
Joined Nov 2005
715 Posts
I will start my build this week. This is going to be fun!!!
soulreaper is offline Find More Posts by soulreaper
Reply With Quote
Old Jun 20, 2011, 08:52 PM
dz1sfb is online now
Find More Posts by dz1sfb
Slipping the Surly Bonds
dz1sfb's Avatar
Attica, MI
Joined Dec 2006
11,418 Posts
Very attractive build!

Ken
dz1sfb is online now Find More Posts by dz1sfb
RCG Plus Member
Latest blog entry: Mini H Quad Project
Reply With Quote
Old Jun 20, 2011, 09:15 PM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
Updated the plans to include CG location. I'd say it should be safe to shift the cg up to 2 cm forward and 1 cm back. She flies well with quite a wide range of CG.

Also included a template for the wheel pants. Should fit any 2 inch wheels. If not, scale it to fit.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Old Jun 20, 2011, 09:41 PM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
Quote:
Originally Posted by soulreaper View Post
I will start my build this week. This is going to be fun!!!
I'm looking forward to it.

I was tempted to build another just to see if there are any bugs with the current plans since I built mine based on the old incomplete and uncorrected plans. Please do inform me if you find any errors or need any clarifications.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Old Jun 21, 2011, 09:59 PM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
Added a firewall template as promised. See first post.

I don't use a firewall for my motor installation so the template is untested but I don't see anything wrong with my measurements.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Old Feb 13, 2014, 04:16 PM
vinnieg is offline
Find More Posts by vinnieg
Registered User
vinnieg's Avatar
United States, NJ, Edgewater
Joined Feb 2012
218 Posts
DTF Pitty

I have the pitty mostly built. Here are a few pics of the plane so far.
vinnieg is offline Find More Posts by vinnieg
Last edited by vinnieg; Feb 13, 2014 at 04:25 PM.
Reply With Quote
Old Jun 28, 2015, 03:22 AM
AuzzieBob is offline
Find More Posts by AuzzieBob
Registered User
AuzzieBob's Avatar
Australia, QLD, Hervey Bay
Joined May 2014
6 Posts
Hi guys......this is my scaled down and modified version of slebetman's Pitty.
Scaled down to 525mm wing span and made out of 6mm depron (it was all I had in my stock 3mm would have been better).....powered with a Park 250 2200kv, GWS 7x3.5 prop, 10amp esc, 3xHK 0S361 servos, R410X Rx and a 300mah 35-70c battery.
All up flying weight 132g.......fly’s beautiful…..planning on using it for a bit of fun indoors as we now have a venue here at Hervey Bay down under!

Thanks for the inspiration everyone........Cheers Rob
AuzzieBob is offline Find More Posts by AuzzieBob
Reply With Quote
Old Jun 29, 2015, 10:59 PM
slebetman is offline
Find More Posts by slebetman
Registered User
slebetman's Avatar
Malaysia, Selangor, Kajang
Joined Jun 2009
1,548 Posts
Nice! Glad to hear it's well-behaved. Mine's not flying anymore. I think it's time I build this again. Maybe a micro version.
slebetman is offline Find More Posts by slebetman
Reply With Quote
Old Jul 02, 2015, 01:00 AM
AuzzieBob is offline
Find More Posts by AuzzieBob
Registered User
AuzzieBob's Avatar
Australia, QLD, Hervey Bay
Joined May 2014
6 Posts
Yes a Micro would be cool even though 525mm is getting there!
Received some 3mm depron today to have a go at something lighter.
Fitted a Lemon Rx with stabilizer yesterday and WOW.... what a difference that makes flying on a windy day......also a spinner for looks!

Below are size comparisons between the UMX Beast and Pitts 1-1S......the Pitty out performs both by far for both 3D and slow flight it does everything.....its quite unbelievable how this thing fly’s. (will get a vid up shortly)

Flew it today at the local field.....the guys were amazed how well it tracks and handles the wind..........the big 50cc gasses were grounded but this Pitty was doing 3D as if there were no wind at all! Have had three people offer to buy it as everybody has fallen in love with it especially when they see it fly!

Thanks again slebetman

Cheers Rob
AuzzieBob is offline Find More Posts by AuzzieBob
Reply With Quote
Old Jul 07, 2015, 10:30 PM
AuzzieBob is offline
Find More Posts by AuzzieBob
Registered User
AuzzieBob's Avatar
Australia, QLD, Hervey Bay
Joined May 2014
6 Posts
Ok........built the micro version of the Pitty Mod scaled down to 420mm wing span and using 3mm depron rather than 6mm.
Modded plans are attached plus all the info and gear that was used are in the pic descriptions.
We have a indoor coming up on the 15th of this month will get some video and post it up!!

Cheers Rob
AuzzieBob is offline Find More Posts by AuzzieBob
Reply With Quote


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Shorts Skyvan 24 inch - test flight video gklein Scratchbuilt Indoor and Micro Models 65 May 01, 2011 09:51 AM
Found Cowl from HobbyKing Pitts-EP 42 inch ARF djmoose Aircraft - Electric - Airplanes (FS/W) 2 Apr 04, 2011 10:28 PM
Wanted WTB Herr 24" Pitts plans swapinthedark Aircraft - Electric - Airplanes (FS/W) 1 Mar 30, 2010 01:02 PM
Wanted WTB plans for the Herr 24" Pitts bipe. swapinthedark Aircraft - Electric - Micro & Indoor Airplanes (FS/W) 0 Mar 29, 2010 09:00 PM
Discussion 24, 30, or 35 inch shoestring kit or plans? paulatgis Sport Planes 4 Nov 01, 2009 05:32 PM