Just to make it clear i will offer a coplete Flyduino KIT.
You will get the Flyduino plus some rows of pinheaders.
All hard to solder SMD parts are soldered you only need to solder those regular trough hole pinheaders which are supplied in the KIT.

Originally Posted by Goofy23

For everyone who is not able to solder the pinheaders, i will do that in the Beta batch.
No Problem.

Hey RCPILOT this sounds good, thanks!

Ken, i will do that, no problem

Also please put me on the list for the next batch...

Alan

this a copter, lets say "flying" with the Flyduino and some BMA020 and a WMP IDG655 Clone.
I am not a skilled Pilot, this one of my first flights.
Bad Setting , Bad flying skills, uncalibrated RC, Bad copter hardware configuration, Bad Video all combined in this this non edited Video
but you see the technical side is working very well, even the crashes where no problem, and i had a lot of them
(the older vids are not with my flyduino)

http://vimeo.com/20148477

Hi Paul,

Put me on the next batch for one unit.

Thank you.

Originally Posted by Goofy23

this a copter, lets say "flying" with the Flyduino and some BMA020 and a WMP IDG655 Clone.
I am not a skilled Pilot, this one of my first flights.
Bad Setting , Bad flying skills, uncalibrated RC, Bad copter hardware configuration, Bad Video all combined in this this non edited Video
but you see the technical side is working very well, even the crashes where no problem, and i had a lot of them
(the older vids are not with my flyduino)

http://vimeo.com/20148477

Paul:

Don't beat yourself up too much. We have all been there. Based on what I saw the stability was not that bad. I have seen and experienced much worse. I am really looking forward to trying your new board. Now if Jussi will get the next gen of the FFIMU ready, then I will be ready.

This is the design of my new Flyduino Quad.

WMP and BMA020.

Still in development and assembly phase.

Hi Mariano,
thanks for the picture, looks very promissing.
It seems you made everything right.
Yo choose the d12 pin which goes over a 3.3V voltage regulator, perfect for the sensor combination you choose.

Here are pictures of the Flyduino Mega on my folding prototype Xframe....

Setup:

KDA 20-20L/18A Plush/1047 APC slofly
G10/Delrin frame with 450 heli booms for arms!
Flyduino Mega and FreeFlight IMU V1.1
Orange RX and HK lipo alarm

AUW is 928 grams with 2200 3S Nano-tech

Oh Jussi, i really like to see this combination flying on this beautifull frame.
Looking forward for it.
NICE

Originally Posted by 420RcPilot

Here are pictures of the Flyduino Mega on my folding prototype Xframe....

Setup:

KDA 20-20L/18A Plush/1047 APC slofly
G10/Delrin frame with 450 heli booms for arms!
Flyduino Mega and FreeFlight IMU V1.1
Orange RX and HK lipo alarm

AUW is 928 grams with 2200 3S Nano-tech

Fantastic folding system, do you have detailed plans?

Excellent looking folding frame you have built there Jussi!


David

sos

Originally Posted by mgros

fantastic folding system, do you have detailed plans?

+1

+2 for me

Update
volver 1 49$ plus 3.50$ shipping paid
Tahoe Ed 49$ plus 6$ shipping paid
whiteturbo 49$ plus 3.50$ shipping paid
blindflight 49$ plus 6$ paid
modesigner 49$ plus 6$ shipping paid
bjornez 49$ plus shipping paid
bas10an 49$ plus shipping paid
alvarepja 49$ plus shipping paid

All have paid for Beta, many Thanks, that was fast.
Also many thanks for paying the fees.
I found your shipping informations in the paypal mails or in the PM´s, will check that when the PCB´s are here.
The Parts are allready on their way to the manufactorer.
He will take a bit longer for the production of the PCB´s, he says 6-7 working days for the Beta Series cause he will do E-tests on every PCB.
But he said he will imediatly start to produce when the PCB´s are good and ready.
I think i can not expect a delivery before end of next week from him.

For all interessted there will be a next batch and a new list.