|Jul 06, 2013, 07:17 PM|
First Flight attempt
Thanks for all the kind words, I'm happy with the way it came out
Well the first flight attempt was less than stellar. Take off was fine, though a bit low on the power. I noticed the motor was louder than usual, that should have been my wake up call. But it was hot and I wanted to get the maiden done. Something happened with the speed controller, as you can see it did not fair well. On the first pass I noticed the smoke coming out of the plane, then on the turn the motor got quiet and it was belly land time. Some minor damage to the rudder was about all the damage to the plane. The plastic Cowl got melted a bit too.
So I took it apart and tested out the motor it was fine. Then I put the SBhobbies spinner pack on and noticed that there was alot of vibration on the motor. So the SB hobbies spinner gets tossed aside for now.
I did end up with a nice weathering effect behind the cowl thought
Time to try again next week I think.
|Jul 11, 2013, 04:57 AM|
Ken , interesting thing .
I have the same spinner on an eflight 110. on the same plane .
I did not like the static testing on the ground and the larger two blade prop leave little room for error .
I so just this week I order two aluminum spinners from http://www.hobbylinc.com/ one for this plane and one for a Seafury .
They are not to bad in the scale shape department and when painted black they wont be far off but they will allow you to cut for what every prop you want to use from two to 5 blades .
Obviously I am going for three and they were relatively inexpensive vs comp spinners .
I hope the problem was not in the ESC, that is a good brand name and they need to deliver on quality especially when your paying more for the expected brand quality !
|Jul 11, 2013, 08:34 AM|
I really believe it was the spinner being out of balance and causeing some addtional load on the motor.
It was a tried and true ESC that I have had for many years, so I dont think it was a controller issue. It was only a 13x10 prop, on 8S so not that big a load on its own.
I tried to put the SBhobbies spinner on a prop balancer but its too large to fit the ones I have.
I have an old P-51 spinner that has been painted black for inital flights. Once the plane gets flight tested then I'll proably get a 3 blade prop and cut the PICA spinner I have for this plane. And maybe even a new cowl
|Jul 27, 2013, 02:29 PM|
Got 3 good flights on the plane today.
The eflite power 90 on 8S is plenty of power. Take offs are quick.
was well behaved in the air.
The split flaps work pretty well, the plane balloons a bit when the flaps are put down, I need to put some down trim in with the flap. Flaps don't seem to slow down the plane all that much, it floats down the runway.
My last landing was a bit hard and I can see a split in the top of the wing where the gear mount is.
I think the prop adapter on the motor is bent just a tad as it makes a bit of noise at the higher end, so I think I'll replace that.
All in all a nice plane added to the collection
|Sep 27, 2014, 12:18 PM|
Well I've had a number of flights on the 190
Its a pretty smooth flying plane and the 8S power 90 is plenty of power
Some in flight shots
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Discussion||Alfamodel focke wulf 190 d9 dora||GGRN||Micro Ready-to-Fly||7||Jul 11, 2012 11:26 PM|
|Sold||Pica Focke Wulf FW-190 D9 kit with extras||jjscott||Aircraft - Fuel - Airplanes (FS/W)||5||Apr 03, 2012 06:08 PM|
|Discussion||Alfa Fw-190 D9 Dora||sperry||Electric Warbirds||22||Jun 19, 2007 02:25 PM|
|Video||Fw-190-D9 "Dora" Maiden Flight||Hans-Joachim||Electric Plane Talk||0||Jan 07, 2007 12:58 PM|
|Discussion||Top Flite FW-190 D9 Dora||andernamen||Fuel Warbirds||3||Oct 28, 2006 11:10 PM|