|Nov 25, 2012, 06:21 PM|
HK250GT 6Ch from a DH9116
My first CP heli, moving from a Double Horse 9116. It's a pretty big
jump, and thought I would share if someone is thinking of moving up.
My next heli would have been an MJX-F45 if it had not been for a
generous donation from another forum member (Thanks Balr14 !!).
I got it mostly assembled, just needed to install electronics.
I spent a ton of time getting the belt drive and tail to operate smoothly.
But now, she spools up like a dream. Smooth and silent. My 9116 sounds like
a dying lawnmower by comparison.
The one-way bearing is awesome to hear spool down, it spins for
quite a while. The belt drive took an hour to adjust, but now you don't
even know it's there.
The head speed is insane. I was scared to put it past 60%
Before I get heavy into the manuals and start setting it up, is there anything
that looks out of place?
|Nov 25, 2012, 08:13 PM|
I would make sure the pin moves very freely up and down inside the anti-rotation bracket. I noticed a lot of the openings in the HK250GT needed some sanding and filing.
|Nov 26, 2012, 04:47 AM|
United Kingdom, England, Witham
Joined Feb 2011
|Nov 27, 2012, 08:26 PM|
Joined May 2011
Why not use a 3s(3 cell) li-po ? Will your canopy fit with the esc mounted side-ways? It looks like you will have to remove your gyro every time you replace your tail boom.(to get to the screws) The HK tail boom is super thin and super fragile.
|Nov 28, 2012, 12:37 PM|
First hover today. I'm so freakin' happy. Took me forever to figure out the
setup / pitch / throttle curves / and every other thing I knew nothing about. LOL.
I have a decent beginner set I made (can still go wild 3D with
When you kick that in (idle-up).... OH MY !!! Freakin AWESOME !!!
(I only did it on the ground). And with the curve, that was only 80% throttle.
This thing is wicked. Very tricky to hover, even with a super docile custom setup.
Of course, it would be easier without the 8 Mph shifting breeze...
If anybody buys a 250GT and uses a SKY-703 radio, and Skyartec head lock gyro, you are welcome to my
setup, posted here. It's a good starting point at the very least.
It took me several hours to figure all the settings out, and this might save
you some time.
|Nov 28, 2012, 01:12 PM|
of power. Idle-up is scary
As far as the gyro, I have a huge roll of servo tape. No big deal if I have to
The only place the canopy is tight is at the battery, as I have it way forward
to try to balance it.
|Nov 28, 2012, 03:01 PM|
Joined Apr 2010
|Nov 28, 2012, 04:03 PM|
You are doing great! But, don't shift in to idle up mode on the ground. You want to be in the air at neutral throttle; much less stress on the equipment. You should probably get used to using throttle hold, rather than cutting the throttle in a crunch situation. When you cut throttle quickly you induce negative pitch, so you come down faster. There are two ways to offset this: use a pitch curve that has very little negative pitch or raise throttle trim. The downside of doing this is it reduces your ability to fight wind. But, if you use throttle trim, you can reduce it with a flick of a finger. The use of throttle trim to control flight characteristics is standard operating procedure on the Thunder Tiger Innovator. It works quite nicely on quads, too.
|Nov 28, 2012, 05:30 PM|
It doesn't get light on the skids at the curve I set until around 2 or 3 deg, so even if I completely cut the throttle it won't pancake. When I enabled idle-up mode I made sure I was at zero or very little pitch. It makes a quick 180, then sits there screaming happily
|Nov 29, 2012, 11:08 AM|
I'm sure that will change once I get used to the completely different flight behavior.
The high head speed makes gyroscopic forces 10 times greater on the 250GT.
The HK250GT handles wind far better than the 9116. It's just harder to fly
because I suck at it.
|Nov 30, 2012, 04:38 AM|
Broke my first part on the 250GT today. I was sliding sideways about a foot
off the ground and a gust made it dip and catch the skid.
Only broke 1 leg, so I can still fly it. But if I had been 2 feet up all
would be good. Stupid.
It can get away from you SOOO FAST... just a nudge on the sticks for a split
second is all you can give it unless you want it taking off like a freakin' rocket.
I need to get a radio with programmable rates and epa's so I can tone it down a
little while I learn.
When it starts to get out of shape, you set it down NOW.
If you have to think about it, it's too late... you've already bit the dust.
All you can do is cut the throttle and hope the blades "bounce" off the blacktop.
This thing is pure evil. Devil bird from hell, I'm not kidding.
I equate it to trying to balance a marble on top of a bowling ball.
I can't believe I have not totaled it already.
But it is so satisfying to fly... the sound, the snappy movement.
The way it holds it's position if you are on the sticks right.
It is just soooo smooth.
The spin rate of this thing is completely nuts.
The tail can spin around so fast it's a blur.
|Nov 30, 2012, 08:10 AM|
If you tipped with enough force to break a skid leg, you should check the feathering shaft. They are always the first thing to bend. When you disassemble the head, pay very close attention to the order of the bushings, bearings, rings, etc. Lots of beginners overlook this. Going from a DH9116 to a 250 clone has to be the biggest jump I've ever heard of. Ranks right up there with starting with the old Walkera 4#3B.
|Nov 30, 2012, 09:14 AM|
until I went to power down.
I was going sideways at a good clip and just nicked a crack in the blacktop.
If it wasn't for that crack, all would be well
The heli kept flying as if it weighed 200Lbs. Didn't even twitch.
Like I said, I didn't even know I broke anything until post flight.
I've ran a pack through since, and it seems ok, nothing different that I can
tell. Still smooth and snappy at the same time
I've got it sitting waiting to see if CA will bond it back together but I doubt
it, they are just too flexible.
|Nov 30, 2012, 09:33 AM|
Glue with CA, warp the break area with dental floss or fine thread and soak with CA. Even if it doesn't hold, you have effectively created a receptacle that you can put hot glue in.
|Nov 30, 2012, 09:37 AM|
On a different note, the 9116 is totaled... Kid was flying, got it too far away.
I took over but it was already too late, couldn't see it.
Had to throttle cut, and this time it needs battery, PCB, head, frame,
and other stuff. Not even sure I want to fix it.
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Sold||Hk250gt||Black_heart||Aircraft - Electric - Helis (FS/W)||2||May 18, 2012 03:30 PM|
|For Sale||HK250gt , Beastx, Satellite||daveapplemotor||Aircraft - Electric - Helis (FS/W)||7||May 09, 2012 04:26 PM|
|Sold||HK250GT with upgrades||newheliguy81||Aircraft - Electric - Helis (FS/W)||3||Mar 20, 2012 10:10 PM|
|Sold||FS/FT HK250GT w/spares||RobDog||Aircraft - Electric - Helis (FS/W)||1||Mar 03, 2012 08:07 PM|