Just starting my Fun Cub build ... Took a bit longer than expected to finish and maiden the XB-70 and YF-23.

Ordered the Fun Cub accessory kit and floor stiffner kit from MorganMill RC.
http://morganmill.com/RC/FunCub_Parts.html
Ordered online on Sept 13, parts arrived cross country today Sept 15th ! Couldn't ask for better than that. Very impressed with the product and service.

Already have landing gear from cublandinggear.com.

Curious how different Zacki CA is from Zap medium CA, so I bought a bottle with my last Multiplex radio gear order. Will give it a try and see.

Used some of my bride's 50% off coupons from Michael's and AC Moore, so I think I have the paint all set ... Still working on a scheme and what to paint before assembly rather than after.

Still not sure if I will install my Multiplex lighting kit on the Cub (shown on box). Trying to work out running wire up to top of rudder without routing it on the outside. Might try drilling up thru rudder for wire....

Hoping to have this one built before the flying season ends.....

Is it a good idea over time to replace the plastic motor mount to an aluminum by Multiplex?

Originally Posted by Bluhammer

Has anyone seen or used on a FunCub, the U shaped metal, plastic, or CF type landing gear found on many planes? Seems like an obvious thing to try. I just dont want to be the first

Blu

Check the first 500 posts or so. Someone used one and posted a picture of it. Sorry to be so vague but yes, someone has.

Here it is

[QUOTE=ltc;22742227]Just starting my Fun Cub build ... Took a bit longer than expected to finish and maiden the XB-70 and YF-23.QUOTE]

Itc - Believe me, I understand taking a bit longer than expected!
It sounds as if your off to a good start! Relax, enjoy the build, and if you get stuck, this is the best place to ask questions!

As far as the lighting - Start the 'tunnel' down the vertical fin with a drill (make sure it's straight), then take a length of brass or aluminum tubing the same size as your drill and file some teeth in one end, you can then hand twist it into the foam using your drilled hole as a guide to complete the tunnel! - Best of luck on your build! ~ Robin

Thanks.
I am planning on using the Fun Cub as a test bed for some new Multiplex 2.4GHz telemetry sensors (battery voltage, current and capacity in real time) in addition to their AntiSpark module and magnetic / LED professional safety switch.

And of course to be a fun plane to just fly, maybe off skis.

Amazing how things have changed in RC since the 70's. My wife laughed the first time she saw me working on a "foamie" rather than a traditional construction plane!

Also going to try a 3 blade prop to see if it helps with the reported resonance/ vibration. Purchased Multiplex power kit.

Originally Posted by ltc

Also going to try a 3 blade prop to see if it helps with the reported resonance/ vibration.

Iv tried that already... doesnt do a thing.

Originally Posted by Slope P

Is it a good idea over time to replace the plastic motor mount to an aluminum by Multiplex?

Slope P,
Search previous posts on this thread and YouTube clips for the Fun Cub.
It is generally recognised as an ideal upgrade.

I bought a Fun Cub recently and it had a metal mount not a plastic mount.
If you are planning on buying a kit check what mount comes with it.

If you already have a kit with a plastic motor mount and want to fit a metal mount send me a PM. I may be able to help you out.
Tony

When I recently pulled my Himax HC3516, I noticed the wire insulation had interfered with the spinning can. I'm replacing with the EMax GT2812/10 which is also a 35mm diameter motor.

Any motor wire routing tips/pictures to make certain of no interference?

Thanks

Aerotony,

Thank you for the reply.

Do they come with either metal or plastic mounts?

My Cub should be here in a few days. Will let you know if I need one when it gets here.

Thanks

LP

Originally Posted by marksp

When I recently pulled my Himax HC3516, I noticed the wire insulation had interfered with the spinning can. I'm replacing with the EMax GT2812/10 which is also a 35mm diameter motor.

Any motor wire routing tips/pictures to make certain of no interference?

Thanks

I put some heat shrink around the wire bundle, which tends to make it want to go straight out. When installed, that tendency causes the bundle to be pushed up against the wall of the airframe. No problem since then on a 37 mm motor.

Originally Posted by Slope P

Aerotony,

Thank you for the reply.

Do they come with either metal or plastic mounts?
My Cub should be here in a few days. Will let you know if I need one when it gets here.

Thanks

LP

Newer produced kits will have the metal mount.
If yours comes with plastic, it was produced before the change over.
Ron

Originally Posted by Woody_99

I put some heat shrink around the wire bundle, which tends to make it want to go straight out. When installed, that tendency causes the bundle to be pushed up against the wall of the airframe. No problem since then on a 37 mm motor.

Super, thanks! I'll give that a try.

Originally Posted by marksp

When I recently pulled my Himax HC3516, I noticed the wire insulation had interfered with the spinning can. I'm replacing with the EMax GT2812/10 which is also a 35mm diameter motor.

Any motor wire routing tips/pictures to make certain of no interference?

Thanks

I cut a hole below the motor down into the air scoop area and feed the motor wires down through and back to my ESC.
Blu

Originally Posted by A Rdnek

Newer produced kits will have the metal mount.
If yours comes with plastic, it was produced before the change over.
Ron

FWIW, I just purchased FC #2, which was ordered through local Hobbytown USA. Still included plastic mount. Of course, I have no idea from which distributor they order and how long it has been in the channel.

Originally Posted by Bluhammer

I cut a hole below the motor down into the air scoop area and feed the motor wires down through and back to my ESC.
Blu

Did you do this before or after joining the fuselage? Thanks