HobbyKing.com New Products Flash Sale
Reply
Thread Tools
Old Jan 25, 2013, 05:39 PM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
Discussion
i have 3 helis one im not sure of other 2

so far i have figered out the other 2 are raptor 30s the one with the fule tank in frount and has a single tail boom brace,can any one tell me what it is im going to put all 3 back in order,is there any newer kits that use the same parts,and are these a 550 size,



bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Sign up now
to remove ads between posts
Old Jan 25, 2013, 07:09 PM
Registered User
Denver, CO
Joined Dec 2005
6,373 Posts
The 30 size usually runs 550mm blades. Can use other blades close in size, but not as common. The Raptor 30 shares many of the Raptor 50 parts, as well as many cloned parts (like from the Klone 50). So they should be easy to get parts for.
Roto Rob is offline Find More Posts by Roto Rob
Reply With Quote
Old Jan 25, 2013, 07:51 PM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
cool,so like the hobbyking 50 parts would fit, if all posible could i get a list of parts that will mix or a list that wont fit if easer thanks i did hapen to figer out the heli it a jr vencher
bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Old Jan 26, 2013, 12:10 AM
Registered User
Denver, CO
Joined Dec 2005
6,373 Posts
Original, and reproduction parts here, for the Raptor.
http://www.helikraft-rchelicopters.c...-v2-parts.html
They also sell the Klone 50. To mix, and match from other helicopters its best to ask about a single part. To many posibilities, some may need other parts to go along with it.
Not sure what a Hobbyking 50 is. They sell an Aeolus, and a JZ. Very different than the Raptors, so entire assemblies would have to be used.
Roto Rob is offline Find More Posts by Roto Rob
Reply With Quote
Old Jan 26, 2013, 03:10 AM
Registered User
Australia, NSW, Eungai Rail
Joined Dec 2012
8 Posts
Venture 30

The heli in front in the first photo is a jr venture 30, finding parts for the ventures is getting harder. What engine does it have?
Chris56 is offline Find More Posts by Chris56
Reply With Quote
Old Jan 26, 2013, 09:22 AM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
roto thanks for the web site, the jr mite be easy to get going being its ccpm if thats the term alot of clone,and aline parts will fit like complete head and tall parts,im going to start getting parts for them, im no pilot so,they mite not leave the ground for a long time,one thing that im not sure on is the expense worth the bild, i would like to run a 4 stroke on at least one,if you guys have parts that will fit these birds, let me know, thanks
bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Old Jan 27, 2013, 12:36 AM
Registered User
Australia, NSW, Eungai Rail
Joined Dec 2012
8 Posts
I would think that raptor parts would be alot easier to source, making them the logical choice for restoration, maybe make one out of two?. if you do find other align parts that work on a venture let me know, I have my doubts thow.
Chris.
Chris56 is offline Find More Posts by Chris56
Reply With Quote
Old Jan 27, 2013, 12:45 AM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
rite know im having trouble finding a radio i would like a 7 ch fm that later i could go to 2.4 and set of blades,main rotor and shaft and 3 motors, linkages
bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Old Jan 27, 2013, 03:17 AM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
ok got the radio,know i need parts,anyone have some there willing to trade out let me know thanks
bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Old Feb 04, 2013, 12:22 PM
Harold
bigfoot3387's Avatar
United States, OK, Davis
Joined Feb 2010
132 Posts
here a update i took apart the motor on the 30 and got it running i took elec tape and taped the blades up all was rusted pretty good little time spent and got all freed up,so yesterday i gave it a try with really bad blades and a prier i gave it a try,for the first time i had a heli lift off and stay in the air lol and i was so happy then the worst thing happened it ran out of fuel, it went down slowly and just stopped i went back to get some more fuel no more in the can if it will fly with blades that have pecis missing and have been crashed then im sure i will have lots of fun, first time hover,i was nerviness i could not think right for 5 min best experience ever with a heli
bigfoot3387 is offline Find More Posts by bigfoot3387
Reply With Quote
Reply


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Gaurdian: I do not have a 3 position switch METATRON12 Eagle Tree Systems 1 Jan 07, 2013 03:48 PM
Discussion I'm thinking of getting a heli but not sure i should take the chance on one from HK Jack Daniels Coaxial Helicopters 9 Dec 17, 2011 11:53 PM
Discussion Help! I have a Vario Silence heli and not sure what motor this is? Ghia Electric Heli Talk 22 Jun 22, 2007 10:55 AM
Discussion not sure if im in right forum, but?? Tbone4life Electric Plane Talk 7 Dec 06, 2006 01:37 PM
need part number for hornet II autorotation kit not sure if im right falcon41176 Micro Helis 3 Dec 21, 2004 12:18 AM