HobbyKing.com New Products Flash Sale
Reply
Thread Tools
This thread is privately moderated by kinderkram, who may elect to delete unwanted replies.
Old Aug 03, 2010, 02:02 PM
OS Sponsor
kinderkram's Avatar
Germany, NRW, Dusseldorf
Joined Jun 2010
5,226 Posts
Build Log
ArduPirates build

The original ArduCopter is a project of the DIY drones team.

The original ArduCopter has gone commercially now...




Meanwhile a very international and very active community used this blog to fill the gaps in the "original" project.

NOTE: The further development of the "official" Arducopter NG code was taken over by the Pirates!
ArduPirates are now teaming up and joining forces with the Arducopter Team.

Read DIYDrones founder Chris Anderson's blog announcement here:
http://diydrones.ning.com/profiles/b...-taken-over-by





Our Group is called ArduPirates



We started a Google Code project which can be found here:
http://code.google.com/p/ardupirates/


Pirate Bastien recently updated the ArduPirates' Wiki

You will find most informations to set up your ArduCopter there.




Pirate Menno aka joebarteam offers a great tutorial on PID tuning


Step-by-step instructions with videos!
Not only applicable for MegaPirates but for every multirotor aircraft needing tuning of the PIDs.

http://www.rcgroups.com/forums/showthread.php?t=1521520






What the Pirates have to offer:

Working Sparkfun Magnetometer, GPS hold, altitude hold with Barometer and Sonar and also automatic camera leveling plus an automatic camera trigger!
Even more: Hein's code applies to Hexa builds. Our Octocopters are using standard ESCs!






Hein demonstrating waypoint Navigation using AC2.0.23 code:

Hexa Waypoint test.wmv (2 min 44 sec)



Greg demonstrating different flight modes

http://vimeo.com/27649497





New! Dani's Universal Ardu Online Configurator for NG code



http://ardupirates.net/config/APNG_Config.php





Ahoi, Pirates!

I installed a new discussion Group on Google:

http://groups.google.com/group/ardupirates



The aim is to speed up the discussion and exchange of news, ideas and new developments faster than before.

If you want to join the Pirates, send me a PM with your google mail address and I'll add you to both the wiki/trunk and the group.

The ArduPirates' Group is open to everyone willing to share experiences on the ArduCopter/ArduPirates project.

Non-members can read the posts but only members can post.

Happy Pirating!





Hooray! Norbert (not me) aka Norf started a Facebook FanPage for the ArduPirates!



All aboard! We're sailing for new harbors!





Norf also started a Build Log for Hexa copters

ArduPirates Hexacopter First Flights (2 min 12 sec)


The unstoppable Norf also created a Vimeo Video Group for Arducopter Pilots:

http://vimeo.com/groups/acp









DIYdrones now supports full installations of the ArduCopter Configurator!



Download the complete installation file for the Configurator 1.22 here.
Install it - all necessary NI runtimes and drivers for your Win OS will be included!

IMPORTANT NOTE!
If you're a non-English user you'll have to change the "regional settings" of your Windows to "English/US" or otherwise your settings will not be saved properly!







HOW TO LOAD THE PIRATES' CODE - by CAPT
Loading ArduPirates code from REV527 zip file (6 min 55 sec)



JANI'S MAGNETOMETER OFFSET CALIBRATION:
ArduCopterNG Magnetometer offset calibration (9 min 51 sec)








VERY IMPORTANT WARNING!!!



When you plug in the USB make sure you don't have your ESCs and motors connected.
Otherwise you will blow your outputs!
References: http://aeroquad.com/showthread.php?6...lot-and-Oilpan
http://diydrones.com/forum/topics/did-i-blow-my-outputs

There are two methods to prevent blowing your outputs:
1. Disconnect all power lines coming from the ESCs before you plug in the USB
2. Connect lipo first before you plug in the USB - and make sure to unplug the USB fisrt before you disconnect the lipo


Atm. the official development is at public beta 2.0 stage.
So please be careful as you might face unwanted and surprising impacts on your setup as the software might be very buggy at some stages!

One of the first official releases will be The ArduCopter Quad. All available informations will be collected there:
http://code.google.com/p/arducopter/...rduCopter_Quad







Interesting Reads:
Dedicated RCG thread for the ArduCopter development:
http://www.rcgroups.com/forums/showthread.php?t=1255371
Another thread here at RCgroups dealing with different Ardu branches:
http://www.rcgroups.com/forums/showthread.php?t=1066119
Jesolin's Mega Index (a must!):
http://www.rcgroups.com/forums/showthread.php?t=1097355





Links:
DIYdrones arducopter page:
http://diydrones.com/profiles/blogs/...arducopter-the
DIYdrones forum:
http://diydrones.com/forum/categorie...istForCategory
AeroQuad forum:
http://aeroquad.com/showthread.php?4...AV-Multicopter!
ArduCopter Wiki:
http://code.google.com/p/arducopter/wiki/ArduCopter







Parts list:

Ardu Pilot Mega (flight controller)

ArduPilot Mega IMU Shield/OilPan (sensor board)

Pin Headers (you need 2 or 1 x 16 rows)

Con Headers (you need 2)

Servo cable (4-8pcs. needed, recently 6 - to connect your rx)

Magnetometer & Cable

GPS & Cable

You can purchase most parts from the AeroQuad store, Sparkfun in the USA, FahPah Shop in Asia, Coolcomponents in the UK or Lipoly and Watterott in Germany (if available).








Software/Firmware*:
*You should give my new Arducopter Installer & Updater Software a try.
See info below.


Note: The public alpha sketches and libraries are available for download herehttp://code.google.com/p/arducopter/downloads/list

Unfortunally the alpha 1.0 isn't represented in the trunk so it might get a bit confusing for beginners.

Instructions for manual setup:

Depending on your OS you may need some drivers for the USB-port of the shield.
http://www.ftdichip.com/Drivers/VCP.htm

Arduino Software needed to upload the firmware to the board:
http://arduino.cc/en/Main/Software
Arduino troubleshouting:
http://arduino.cc/en/Guide/Troubleshooting

ArduCopter Configurator:
Sorry, this fine piece of software won't be further developed by Ted Carancho any longer (see message above)
http://code.google.com/p/arducopter/...tor/Executable

ArduCopter-Libraries:
http://code.google.com/p/arducopter/...runk/libraries
Installation instructions for the libraries:
http://code.google.com/p/arducopter/...nk/Install.txt

ArduCopter firmware:
http://code.google.com/p/arducopter/...unk/Arducopter
You need to download all files, put them into a folder i.e. named "ArduCopter" within the given path of the Arduino software.


See more pics of the Arducopter Configurator in the attachements.

The configurator is also a great resource when it comes to training your thumbs. You can see any reaction when moving the sticks and use it like some kind of "flight commands simulator".
That's how I found out that my yaw-stick-thumb has to be trained a lot more ...





Always in mind to make the whole software stuff easier and faster, here comes the latest release of my
ArduCopter Installer & Updater Software.

I decided to split the installation and the update process.

You'll need to download these 2 files:

The Kinderkram Quad Installer:
http://www.board-portal.de/ArduCopte...-Installer.exe

Only needed if you DIDN'T already use my setup program.



New: The Arducopter Quad Updater
http://www.board-portal.de/ArduCopte...er-Updater.exe

Only 6,5MB file size. Will automatically load the Arducopter sketches. You only need to press the Upload button in Arduino.



The recent version 1.0 contains
- Arducopter sketches & libraries from the public alpha 1.0
- Arduino 0021
- Configurator 1.1 (Important: Install it to C:\Arducopter\ArducopterConfigurator !)



After the installation in C:\Arducopter you can easily upgrade the Configurator to version 1.22 manually. Just press the "Update" button.
If you bump into any problems, have a look into C:\Arducopter\sketches\Arducopter. If there's a Arducopter_alpha_RC1.pde - delete it!
And please check if all settings apply to your setup, i.e. COM-Ports , Baudrates etc.

Always download new updates from my server to C:\Arducopter\Updates

You can download installation instructions as PDF here (65KB):
http://www.board-portal.de/ArduCopte...structions.pdf






I also made a small tutorial for the use of SVN for easy semi-automatic updates of upcoming releases directly from the Arducopter trunk:
http://www.rcgroups.com/forums/showthread.php?t=1317685



Here's a short How-To:

After the installation of Tortoise SVN (http://tortoisesvn.net/downloads)

1. SKETCHES: right-click on the C:\Arducopter\sketches\Arducopter folder. As "URL of Repository" put in http://arducopter.googlecode.com/svn/trunk/Arducopter When you click "OK" all previous files will be overwritten.

2. LIBRARIES: right-click on the C:\Arducopter\arduino\libraries folder. As "URL of Repository" put in http://arducopter.googlecode.com/svn/trunk/libraries

3. CONFIGURATOR: right-click on the C:\Arducopter\ArducopterConfigurator folder. As "URL of Repository" put in http://arducopter.googlecode.com/svn...tor/Executable



Please report all bugs here and Have Fun!





Software repository for ArduCopter:
http://code.google.com/p/arducopter/...unk/Arducopter

Build instructions (official ArduPilot Mega manual):
http://code.google.com/p/ardupilot-mega/wiki/home?tm=6






The above image shows the abilities of the 2 boards connecting sensors. This sketch is ment for quadrocopters.



Setup for the X-mode (image of +-mode see attachments)














Jakub's Frame:
http://www.kkmulticopter.com/index.p...rame-by-jakubj



Jakub is a nice guy from Krakow in Poland. He sells his standard quad frame for 59$ plus decent shipping fees worldwide.
His brand new store offers a large amout of different frames (from Tris to Hexa) now: http://www.quadframe.com

Some samples:




He's also very active in the RCG forums and you can read a thread about his new creations here:
http://www.rcgroups.com/forums/showthread.php?t=1310314


Video of Jakub's frame assembly:
Foldable quadcopter frame assembly manual (4 min 25 sec)




Motors:
http://carancho.com/AeroQuad/store/i...products_id=50

Escs:
http://carancho.com/AeroQuad/store/i...products_id=51

Of course you can use other frames, motors and escs.

A great resource for informations on motors is Old Man Mike's regularly updated thread:
http://www.rcgroups.com/forums/showthread.php?t=1006721








COSTS

Motors 4 x 20$ = 80$
ESCs 4 x 20$ = 80$
Frame = 70$ - 150$
APM = 60$
IMU = 160$
CON/PIN HEADERS = 10$
CABLE = 10$
CONNECTORS = 10$
SUM = 480$ - 560$

COMPASS = 40$
GPS = 35$
CABLE = 5$
SUM = 80$

+SHIPPING ~ 10$ - 60$

COMPLETE ~ 570$ - 700$

Depending on what you want - you could build your own cheap frame, buy cheaper components - you can get away with less than 400$ for a standard version with triple axis gyros, accs and pressure sensor.

Complete costs may vary if you add shipping, tax and customs.
For European customers the overall costs will be around 600 - 700€ atm.





I. SOLDERING

If you don't have any experience in fine soldering and/or are not willing to learn - forget it!
You better look for someone who does the soldering for you. You can ask tv or radio repair shops or any company dealing with reparation of electronic parts in your hometown.
A skilled solderer should complete this within around 30mins or less.
List of video tutorials for those who want to learn soldering:
http://www.google.de/search?hl=de&cl...ed=0CHEQlAYwAA

It's already been discussed to sell pre-soldered and pre-configured kits in the future. So keep an eye on the mentioned forums and threads.

If you're willing to give it a try you should buy some low-cost tools. These are:
- a fine soldering iron with 1mm tip
- magnifying glasses with a stand
- of course some 1mm soldering wire
- a clean sponge for cleaning the tip








Assembly Tutorial for the APM/APM shield:
http://code.google.com/p/arducopter/wiki/APM_IMU






ArduPilot Mega - Assembly (0 min 16 sec)






II. HANDLING OF THE FIRM- & SOFTWARE*
*You should give my new Arducopter Installer & Updater Software a try.
See the info above.

[IMG]IMG]http://arducopter.googlecode.com/svn/images/warning_rc_connection.png[/IMG][/IMG]


Recommended read: The ArduCopter Wiki "Programming ArduPilot Mega"



1. Copy the arduino-0021 folder onto your harddisk.
Follow the setup instructions from the Arduino-0021-README.txt
Some of the necessary libraries are already included.
In case of problems, consult the Arduino Trouble Shooting (http://arduino.cc/en/Guide/Troubleshooting)

2. Install the USB Serial Drivers if necessary. When you plug in the Megashield (oilpan), you might be asked for the drivers (not needed on Win7 and Mac OS 10.5x).
Point the installer to the "USB Serial Drivers" folder.

3. Upload the ArduCopter firmware to the APM.
- plug the board into the USB
- start arduino.exe from the arduino-0021 folder
- go to -> File -> Preferences and set the location for your sketches. Choose the folder that resides above the "ArduCopter-firmware" folder
- go to -> Tools -> Board and choose the "Arduino Mega" as your board
- go to -> Tools -> Serial Port and choose the port that was previously set up after you installed the USB Serial Driver (usually COM3)
- go to -> Tools -> Serial Monitor and set the port speed to 115200 baud
- go to -> File -> Sketchbook -> ArduCopter
- click on the "Upload"-button. Then the arduino software compiles the firmware and uploads it afterwards. You should get the message "Done Uploading"

4. Install the Arducopter Configurator by starting the setup.exe
After installation start the Arducopter Configurator software
- choose COM3 als serial port (if it's the desired port - see above)
- type 115200 baud for the "Baud Rate", set the timeout to 30 sec
- click on Connect

IMPORTANT NOTE!
If you're a non-US user you'll have to change the "regional settings" of your Windows to "English/US" or otherwise your settings will not be saved properly!


5. Configure your copter
- go to "Initial Setup" and click on "Initialize EEPROM"
- in the status bar it should say "Initializing done"
- Go to the "Calibration" screen and set the following values:

You only need to adjust the PID values for the accels.
Leave the others untouched for now.

To set the values you'll have to choose "Calibration" from the upper right drop down menu. You can lower or higher the values on the right hand side and press "Update" each time.

Lower Pitch = Lower Values
Lower Roll = Higher Values
Lower Z Axis = Higher Values


Accel Roll & Pitch have to be near zero, while Accel Z should be near 408.
Also check the artificial horizon. If the gyros are playing rollercoaster it's time for a rrreeesssettt. But disconnect from the Configurator first or it will hang.

- Go to "Transmitter Adjustment" and check if your commands are displayed correctly


See more images for a step-by-step configuration in the attachements below.






A NOTE OF WARNING!!!
The firm- and software is at alpha stage. That means there are still several bugs in the code that have to be ironed out!





III. CALIBRATING ESCS and getting the MOTORS working

Usually all calibration will be done through the configurator. For now you can only initialize the EEPROM and calibrate your tx/rx within the version 1.21.



So you'll have to do the calibration manually:
Plug each ESC attached to the motors into the throttle channel of your rx.
Switch on your tx and go to full throttle. Plug in the lipo for the motors. You'll here 2 series of beeps confirming the correct calibration.
Then pull your throttle back to zero and wait for the beep code. When done unplug the lipo, switch the tx off, plug the lipos again and switch on the tx again.

Do this for each ESC you want to calibrate.

After the calibration is done you can plug all cables in place and try to arm the motors by pushing the throttle stick to the lower right position.
To disarm the motors push it to the lower left.



ArduCopter Quad uses 4 motors in total and they are named as:

+ Configuration
OUT0 = Right motor (CCW)
OUT1 = Left motor (CCW)
OUT2 = Front motor (CW)
OUT3 = Rear motor (CW)


X Configuration
OUT0 = Front/Right motor (CCW)
OUT1 = Back/Left motor (CCW)
OUT2 = Front/Left motor (CW)
OUT3 = Back/Right motor (CW)

CCW = Counter Clock Wise rotation (eg backwards) CS = Clock Wise (eg forward like clock does)





Aaron's Tutorial for the Ublox GPS


http://www.rcgroups.com/forums/showthread.php?t=1339624





Here's a description on how to set up the latitude:

In the "Position Hold" settings of the configurator you need to change the value for the "Geo Correction Factor". Where GCF = cos(latitude).
You can find the value of your current latitude via Google Maps or Google Earth and use a simple cosinus calculator like this:
http://www.in-screen.de/swf/sinusrechner.html

- Go to Google Maps
- Search for your location
- Click the right mouse button on the marker and choose "what is here"
- Then it writes the values into the search field
- The first value is your Latitude



Check "DEG." and put in the latitude value (in my case 51.2), then press "cos".
In my case the resulting 0,626 is the value you need for the Geo Correction Factor. Press "Update" in the configurator afterwards.





BUILD LOG IS NOT YET FINISHED! EXPECT MORE TO COME!!!


Started by Norbert Machinek aka kinderkram
Düsseldorf, Germany 08/04/2010


kinderkram is offline Find More Posts by kinderkram
RCG Plus Member
Last edited by kinderkram; Oct 15, 2011 at 04:44 AM.
Reply With Quote
Sign up now
to remove ads between posts
Old Aug 03, 2010, 05:54 PM
Tokyo, Japan
Tokyo, Japan
Joined Jun 2010
52 Posts
Hi, kinderkram

I am very intersted in this project.
I am one of a UAV fans in Japan. Now I own one 330X and one home-made
octo with a brain of GU-344.
I want to upgrade my Octo to a brain of Arducopter.
Is it possible?
If possible, at least What parts should I buy from the Ardu store?
I want functions on my Octo at least the followings:
1. Position hold
2. RTH
3. Altitude hold
Could you give me some infos?
masao1310 is offline Find More Posts by masao1310
Reply With Quote
Old Aug 03, 2010, 08:05 PM
Clyde, Ca. USA
Clyde, Ca. USA
Joined May 2007
2,382 Posts
Kinderkram You are updating this thread very quickly.
Thank you for all the info on this Arduino quad.
After putting all the parts together did you have to program or download anything to get started?
john339 is offline Find More Posts by john339
Reply With Quote
Old Aug 03, 2010, 08:35 PM
OS Sponsor
kinderkram's Avatar
Germany, NRW, Dusseldorf
Joined Jun 2010
5,226 Posts
Hi Masao,
all the parts needed are listed above.

The sensor shield comes with triple axis Invensense gyros, triple axis accelerometers and a Bosch absolute pressure and temperature sensor.
For RTH/AH/PH and waypoint navigation you need the magnetometers/compass and the Mediatec 10Hz GPS which comes as a nice pluggable breakout board.

Note that these functions are still in development and even the hardware could change in the next few months. But I'm quite sure that octos will be just a matter of programming.

I've already seen a flyable hexacopter in another branch of the Ardu development scene.
Dunno if octos with 8 independently controlled motors is as easy to set up.
kinderkram is offline Find More Posts by kinderkram
RCG Plus Member
Reply With Quote
Old Aug 03, 2010, 08:39 PM
OS Sponsor
kinderkram's Avatar
Germany, NRW, Dusseldorf
Joined Jun 2010
5,226 Posts
Quote:
Originally Posted by john339 View Post
Kinderkram You are updating this thread very quickly.
Thank you for all the info on this Arduino quad.
After putting all the parts together did you have to program or download anything to get started?
Hi John,
I'll bundle a nice package for starters. Promised.
But that'll take some time. I'll try not to stress your patience...
kinderkram is offline Find More Posts by kinderkram
RCG Plus Member
Reply With Quote
Old Aug 03, 2010, 08:49 PM
Tokyo, Japan
Tokyo, Japan
Joined Jun 2010
52 Posts
Thanks, kindeKram
I read some Wiki pages and thought this Arducopter can be applicable to my case.
I ordered the parts you kindly listed. But some of parts are out of order now, for example, MediaTek MT3329, 3x8 Right Angle Pin Headers.
I hope those will soon be available.
One question:
It is uncertain on the chart you listed avobe that which numbers (from 0 to 7) I should use when connect 4 ESCs of quadcopter to the ArduPilot Mega board.
masao1310 is offline Find More Posts by masao1310
Reply With Quote
Old Aug 03, 2010, 09:14 PM
Tokyo, Japan
Tokyo, Japan
Joined Jun 2010
52 Posts
I think I should wait until starter kit is released.
masao1310 is offline Find More Posts by masao1310
Reply With Quote
Old Aug 04, 2010, 11:06 AM
Clyde, Ca. USA
Clyde, Ca. USA
Joined May 2007
2,382 Posts
Kinderkram I believe I can attempt this now that you have so graciously set up the steps and what is needed.
I ordered the frame from Jakub and will order the brain and oilpan next.
I have a DX6 and hope it will work OK with this brain.
I went to purchase the oil pan and it says it now comes with pin headers.
Does that mean I can skip ordering the pin headers and con headers?
Do I need to order a cable to let the brains talk with my computer?
I ordered a USB cable too.
All ordered now but I had to go to diffrerent places to get all the stuff. Is this a popular design and are there a lot of them flying?
Thank you.
John
john339 is offline Find More Posts by john339
Last edited by john339; Aug 04, 2010 at 12:45 PM. Reason: more questions
Reply With Quote
Old Aug 04, 2010, 02:37 PM
Registered User
Hoofddorp, Netherlands
Joined Sep 2004
3,917 Posts
Great work, Norbert !!! This is really an example build thread and should certainly help me get and ArduCopter based APMk in the air once I have received the last connectors !
Arthur P. is offline Find More Posts by Arthur P.
Reply With Quote
Old Aug 04, 2010, 03:51 PM
Registered User
Bill Glover's Avatar
United Kingdom, Bracknell
Joined Nov 2000
11,642 Posts
Quote:
Originally Posted by kinderkram View Post
I'll bundle a nice package for starters. Promised.
Sounds good!
Bill Glover is offline Find More Posts by Bill Glover
Reply With Quote
Old Aug 04, 2010, 05:18 PM
Registered User
Michigan
Joined Dec 2008
2,007 Posts
Nice

Hey there nice job hard to keep up with you keep the good work up
tom6696950 is offline Find More Posts by tom6696950
Last edited by tom6696950; Aug 04, 2010 at 05:28 PM.
Reply With Quote
Old Aug 04, 2010, 05:47 PM
Registered User
Michigan
Joined Dec 2008
2,007 Posts
going to be fun will start ordering more Thursday need to spend some time with the boss (ak Wife) will check back later kinderkrams look what you have started
tom6696950 is offline Find More Posts by tom6696950
Last edited by tom6696950; Aug 16, 2010 at 10:12 AM. Reason: spell
Reply With Quote
Old Aug 04, 2010, 07:04 PM
Tokyo, Japan
Tokyo, Japan
Joined Jun 2010
52 Posts
I ordered all the parts required except GPS board out of order.
The shop who sells ArduPilot Mega board is now on vacation.
So all package will be reached in 2 weeks.
I am looking forward to having all the parts on my DIY octo.
I will report on making my octo.
masao1310 is offline Find More Posts by masao1310
Reply With Quote
Old Aug 04, 2010, 08:35 PM
Clyde, Ca. USA
Clyde, Ca. USA
Joined May 2007
2,382 Posts
tom6696950 Good to see you here. I needed more brain power for a quad and the MK is too expensive.
This quad seems to have the right brains and I can afford to work with it.
If all goes well, I can save up for the GPS next.
john339 is offline Find More Posts by john339
Reply With Quote
Old Aug 05, 2010, 06:04 AM
OS Sponsor
kinderkram's Avatar
Germany, NRW, Dusseldorf
Joined Jun 2010
5,226 Posts
Quote:
Originally Posted by john339 View Post
I have a DX6 and hope it will work OK with this brain.
Yes, a 6ch. TX/RX is minimum for the ArduCopter at this stage (4 channels for flying and 2 AUX to switch the modes). In future you'll need 8 channels to conduct all the features that come along with this aircraft.

Quote:
I went to purchase the oil pan and it says it now comes with pin headers.
Does that mean I can skip ordering the pin headers and con headers?
Do I need to order a cable to let the brains talk with my computer?
I ordered a USB cable too.
The oilpan comes with all it's headers but need to be soldered anyway. The other pins I mentioned in the list are for the flight controller.

Quote:
All ordered now but I had to go to diffrerent places to get all the stuff. Is this a popular design and are there a lot of them flying?
Thank you.
John
Atm there's only the DIYdrones and the Aeroquad store that have all the parts needed in stock. Due to availability I had to order my stuff from 3 different stores and one local shop. Hopefully there will be kits offered in the near future and bundles for ARF/RTF builds.
This project is still in development. That's why you can't go into a shop and buy the whole stuff at once.
kinderkram is offline Find More Posts by kinderkram
RCG Plus Member
Last edited by kinderkram; Aug 05, 2010 at 06:20 AM.
Reply With Quote
Reply

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log What to Build??? O What to Build????? helidude2 Micro EDF Jets and Power Systems 10 Jul 10, 2014 10:14 AM
Discussion ArduCopter Project Update km28104 Multirotor Talk 176 Apr 18, 2011 11:56 AM
Poll Tamiya Wild One- To build or not to build? peacekeeper94 Off-road Cars 11 May 29, 2010 05:05 AM
Discussion Build Log: Monogram "build'n fly" DHC-2 Beaver lw_hughes Scratchbuilt Indoor and Micro Models 9 Nov 17, 2009 08:01 PM
Question AMD Phoenix (Wingeron) Build Questions, Build, and Pics Greygoosegregg Slope 82 Sep 11, 2009 04:40 PM